RDM EC9100i series User manual

EC9100i and EC9600i
Series Scanner
User Guide
January 2016

EC9100i and EC9600i Series Scanner User Guide Copyright
©2016 RDM Corporation Page 2
Copyright
Copyright ©2016 by RDM Corporation.
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or
transmitted, in any form or by any means, electronic, mechanical, photocopy, recording, or otherwise,
without the prior written permission of RDM Corporation.
Trademarks
RDM, ITMS, Simply Deposit, Simply Deposit Mobile, Dynamic Decisioning Portal, DepositWatch+, In-Line
MICR Verifier, EC6000i, EC7000i, EC7500i, EC9000i, EC9100i, and EC9600i are trademarks or registered
trademarks of RDM Corporation. All other brands and their products are trademarks or registered
trademarks of their respective holders and should be noted as such.
Disclaimer
RDM Corporation makes no warranty with respect to the adequacy of this documentation, programs, or
hardware that it describes for any particular purpose or with respect to the adequacy to produce a
particular result. In no event shall RDM Corporation be held liable for special, direct, indirect, or
consequential damages, losses, cost, charges, claims, demands, or claim for lost profits, fees, or
expenses of any nature or kind.
RDM Corporation
www.rdmcorp.com
End-User/Customer Agreement
Please read the end-user/customer agreement regarding software license and warranty terms during
the installation of the application.

EC9100i and EC9600i Series Scanner User Guide Compliance statements
©2016 RDM Corporation Page 3
Compliance statements
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
Warning: Changes or modifications not expressly approved by RDM could void the user’s authority to
operate the equipment.
All units covered by this manual have no user-serviceable parts inside. In the event repairs are ever
needed to any RDM product, they should be performed by RDM Corporation or an authorized
representative of RDM Corporation. For information please contact RDM Corporation,
619A Kumpf Drive, Waterloo, Ontario, Canada N2V 1K8, at 1-800-567-6227, or RDM’s US service agent
below.
US Service Agent
William Buser
[phone]
[e-mail]

EC9100i and EC9600i Series Scanner User Guide Contents
©2016 RDM Corporation Page 4
Contents
Copyright....................................................................................................................................................... 2
Compliance statements ................................................................................................................................ 3
FCC Compliance Statement....................................................................................................................... 3
Contents........................................................................................................................................................ 4
Introduction .................................................................................................................................................. 7
About this guide........................................................................................................................................ 7
Requirements............................................................................................................................................ 7
Recommendations .................................................................................................................................... 8
Models and features ..................................................................................................................................... 9
Your scanner ...........................................................................................................................................10
Application button ..................................................................................................................................10
EC9100i and EC9600i series scanner (most models) .............................................................................. 11
EC9100i and EC9600i series scanner with printer ..................................................................................12
Internal components...............................................................................................................................13
Inside the front cover - side view........................................................................................................ 13
Inside the front cover - back view....................................................................................................... 14
Inside the front cover and endorsement printer cover - top view.....................................................15
Connection ports..................................................................................................................................... 16
Setting up your scanner ..............................................................................................................................17
Choosing a location................................................................................................................................. 17
Unpacking the shipping box.................................................................................................................... 17
Connecting the power cord .................................................................................................................... 18
Disconnecting the power cord............................................................................................................18
Installing cartridges and paper roll ......................................................................................................... 18
Drivers and applications..........................................................................................................................18
EC9600i scanning application requirements.......................................................................................19
Connecting the EC9600i network scanner..............................................................................................19
Operating the scanner ................................................................................................................................22
Preparing documents..............................................................................................................................22

EC9100i and EC9600i Series Scanner User Guide Contents
©2016 RDM Corporation Page 5
Feeding documents................................................................................................................................. 22
Single-feed (SF) models....................................................................................................................... 22
Auto-feed (AF) models........................................................................................................................ 23
Swiping magnetic stripe cards (optional) ............................................................................................... 23
Imaging identification cards.................................................................................................................... 24
Understanding light signals.....................................................................................................................24
EC9100i series signals ......................................................................................................................... 24
EC9600i series signals ......................................................................................................................... 25
Maintaining your scanner ...........................................................................................................................26
Removing the covers...............................................................................................................................26
Front cover.......................................................................................................................................... 26
Endorsement printer cover................................................................................................................. 26
Franker and endorser inkjet cartridges .................................................................................................. 27
Installing the franker cartridge ...........................................................................................................28
Installing the endorser inkjet cartridge............................................................................................... 28
Replacing the inkjet blotter ................................................................................................................29
Replacing the paper roll for the printer.................................................................................................. 30
Cleaning the scanner............................................................................................................................... 31
Cleaning the outside cabinetry ...........................................................................................................31
Cleaning the inside of the scanner unit .............................................................................................. 31
Cleaning the image sensor.................................................................................................................. 31
Troubleshooting.......................................................................................................................................... 32
Scanner does not respond ...................................................................................................................... 32
Card transactions do not function properly ...........................................................................................32
Printer does not print ............................................................................................................................. 32
Can’t connect to EC9600i network scanner............................................................................................32
EC9600i network scanner dashboard .........................................................................................................34
Testing the EC9600i network scanner ....................................................................................................35
Specifications ..............................................................................................................................................37
Part Numbers.......................................................................................................................................... 40
Scanners .............................................................................................................................................. 40

EC9100i and EC9600i Series Scanner User Guide Contents
©2016 RDM Corporation Page 6
Additional parts................................................................................................................................... 41
Warranty Information.................................................................................................................................42
LIMITED WARRANTY: .............................................................................................................................. 42
WARRANTY SPECIFICS:............................................................................................................................ 43

EC9100i and EC9600i Series Scanner User Guide Introduction
©2016 RDM Corporation Page 7
Introduction
The RDM EC9100i and EC9600i series scanners provide affordable functionality in a compact, efficient
design. Featuring RDM’s industry leading Progressive MICR Method and imaging technology, the
EC9100i and EC9600i series scanners deliver optimum MICR read rates and image quality.
With several models and feature options to choose from, the RDM EC9100i and EC9600i series scanners
are an ideal fit for payment applications such as remote deposit capture, check cashing, teller capture,
healthcare POS, retail POS, and walk-in bill payments. Scanners are available in single-feed and auto-
feed models, with speeds up to 90 documents per minute on some models.
Additionally, the EC9600i series network scanners provide IP addressability and increased connectivity
options. Embedded software enables easy one-time, web-based configuration, eliminating the need for
installation on a PC. The EC9600i network scanner can be used as a shared resource that works with
workstations, terminals, or tablets; can be used with Windows, Mac OS X, and Linux operating systems;
and is compatible with Citrix and other thin client environments.
About this guide
This guide describes the EC9100i and EC9600i series scanners, some basic operations, and how to
maintain your scanner. For instructions on how to use your scanner to scan documents with your
computer, contact your solution provider.
Requirements
The scanner is for indoor use only. Keep the scanner dry; avoid areas of high humidity.
Do not remove any parts from areas that are not described in this guide. Removing parts from areas not
described in this guide will void the warranty.
When you are working inside the scanner, such as when you are replacing the franker cartridge, make
sure the scanner’s power is disconnected.

EC9100i and EC9600i Series Scanner User Guide Introduction
©2016 RDM Corporation Page 8
Recommendations
Record all distributor contact information for future reference.
Save the original box and packing material. Reuse them if the unit must be shipped to a new location or
returned for service.
Position the unit so that the operator has easy access to the document path and a clear view of the LED.
Do not put the unit close to a heat source, in direct sunlight, or close to any device that can emit
electromagnetic interference, such as a computer monitor or power adapter.

EC9100i and EC9600i Series Scanner User Guide Models and features
©2016 RDM Corporation Page 9
Models and features
The RDM EC9100i and EC9600i series scanners are available in several optional model configurations. All
models include an integrated ID card imager and a franker.
All scanner models can also be licensed to perform optical character recognition (OCR) on documents
with machine printed text (remittances, pay stubs). This can be used with different applications such as
walk-in bill payment. You can tell if your scanner is licensed for OCR by the label on the bottom or back
of the scanner.
The following table lists the available EC9100i and EC9600i models. A complete list of models, options
and part numbers can be found in the Part Numbers section at the back of this guide.
Model Description
EC9103f Auto-feed scanner with endorser. (30dpm and 90dpm models available)
EC9104f Auto-feed scanner with endorser and MSR. (30dpm and 90dpm models available)
EC9107f Auto-feed scanner with endorser and receipt printer. (30dpm and 90dpm models
available)
EC9108f Auto-feed scanner with endorser, MSR, and receipt printer. (30dpm and 90dpm models
available)
EC9111f Single-feed scanner.
EC9112f Single-feed scanner with MSR.
EC9603f Auto-feed network scanner with endorser. (30dpm)
EC9604f Auto-feed network scanner with endorser and MSR. (30dpm)
EC9607f Auto-feed network scanner with endorser and receipt printer. (30dpm)
EC9608f Auto-feed network scanner with endorser, MSR, and receipt printer. (30dpm)
EC9611f Single-feed network scanner.
EC9612f Single-feed network scanner with MSR.

EC9100i and EC9600i Series Scanner User Guide Models and features
©2016 RDM Corporation Page 10
Your scanner
There is a label on your scanner that includes the following details about your scanner:
•The scanner’s model number
•MAC address (EC9600i models only)
•The scanner’s serial number
•The speed of your scanner (30 documents per minute in the example below)
•Whether the scanner is licensed for OCR (the example below is licensed for OCR scanning)
You can locate your scanner’s label on the bottom or back of your scanner.
Application button
This button is located on the front right of the scanner. The light indicates the status of the scanner. For
more information, see Light signals and beeps on page 24.
Third-party applications can configure the application button to perform
a variety of functions. These functions might include opening a
document, launching a website, or starting an application. Not all
applications use the application button.
Developers can find information about programming the application
button in the help file that is included with RDM’s application
development kit (ADK). Developers can obtain the ADK by contacting RDM.
Note: The application button is not supported on some scanner models. The LED is supported on all
models.
Model number
Scanner speed
OCR license
MAC address

EC9100i and EC9600i Series Scanner User Guide Models and features
©2016 RDM Corporation Page 11
EC9100i and EC9600i series scanner (most models)
Exit pocket
Exit extension
Insertion extension
Endorsement printer cover
Front cover
Application button and
scanner status LED
Insertion
hopper

EC9100i and EC9600i Series Scanner User Guide Models and features
©2016 RDM Corporation Page 12
EC9100i and EC9600i series scanner with printer
Application button and
scanner status LED
Front cover
Endorsement printer cover
Exit pocket
Insertion
hopper
Printer door release button
Printer door
Printer paper feeder
Pocket stop

EC9100i and EC9600i Series Scanner User Guide Models and features
©2016 RDM Corporation Page 13
Internal components
Inside the front cover - side view
Document feeder
Insertion hopper
Image sensor
(closed)
ID card entry slot

EC9100i and EC9600i Series Scanner User Guide Models and features
©2016 RDM Corporation Page 14
Inside the front cover - back view
Franker cartridge
latch
Franker
cartridge
Metal Plate
(aligns with slot in
franker cartridge)
ID card entry slot

EC9100i and EC9600i Series Scanner User Guide Models and features
©2016 RDM Corporation Page 15
Inside the front cover and endorsement printer cover - top view
Exit pocket
Magnetic
stripe reader
(MSR)
Document track
Franker
Back
Front (extensions retracted)
Insertion hopper
Image sensor
and panels
(closed)
ID card entry slot
Scanner LED
Metal post for top cover
Metal post for
top cover
Endorsement printer
(select models)

EC9100i and EC9600i Series Scanner User Guide Models and features
©2016 RDM Corporation Page 16
Connection ports
EC9100i
EC9600i
Note: Not all scanner models include every item shown in the diagrams.
Connector Description
USB hub
(Auto-feed models only)
You can use these ports to connect peripheral devices.
Note: You cannot connect the scanner to your computer with these ports.
USB High-speed 2.0 (480 Mb/s). Use this port to connect to a computer. You
must use the USB A to B cable.
Power Connect the power adapter to this port.
K-Slot The K-Slot or Kensington® Security Lock lets you secure the unit with a cable
(not provided) that locks into the slot. Cables can be purchased from your
local computer supply store.
Ethernet
(EC9600i only)
Use these ports to connect the scanner to your network with an Ethernet
cable.
EC9603f, EC9604f, EC9607f, and EC9608f scanners include a two-port
Ethernet hub.
EC9611f and EC9612f scanners have one Ethernet port.
USB hub
USB
Power
K-slot
USB
Power
Ethernet
Ethernet
USB hub

EC9100i and EC9600i Series Scanner User Guide Setting up your scanner
©2016 RDM Corporation Page 17
Setting up your scanner
To set up your scanner:
•Choose a location.
•Unpack the shipping box.
•Inspect the scanner’s features.
•Insert the franker cartridge (if your application franks documents).
•Insert the endorser inkjet printer cartridge (sold separately).
•Insert the receipt paper roll, if one is included with your scanner.
Choosing a location
Locate your scanner in a place that:
•Has a flat surface, such as a counter top or table.
•Is convenient for the scanner operator.
•Offers adequate ventilation and protection from elements such as heat, dust, oil, or moisture.
•Is close to the application computer. Depending on your scanner model, a USB 2.0 high speed or
Ethernet connection is required.
•Is close to an electrical outlet.
Unpacking the shipping box
1. Open the top of the box.
2. Remove and unwrap the items. Lift the scanner out of the box from the bottom of the scanner.
3. Save the box and packing material for future use.
The shipping box includes the following items:
•Scanner
•USB cable (A to B)
•Ethernet cable (network models)
•Power adapter
•Franker cartridge (auto-feed models)
•5-pack inkjet blotter (models with endorsement printer)
•3” thermal receipt paper roll (models with receipt printer)

EC9100i and EC9600i Series Scanner User Guide Setting up your scanner
©2016 RDM Corporation Page 18
Connecting the power cord
1. Align the flat side of the power connector so that it is facing up.
2. Insert the round end of the power cord into the power port on the back of the scanner.
When the cord is pushed in completely, it clicks into place.
3. With the power cord connected to the power adapter, plug the other end of cord into an
electrical outlet.
Disconnecting the power cord
Caution: Disconnecting the scanner from a power source while the scanner is processing a transaction
might cause data loss.
The power cord has a sleeve on it that secures it to the unit. The security sleeve prevents the power
cord from being pulled out of the unit accidently.
1. Hold the unit in place with one hand to prevent the unit from falling.
2. With your other hand, slide the power cord security sleeve back and pull the power cord free of
the scanner.
Installing cartridges and paper roll
For installing the franker cartridge, see Replacing the franker cartridge on page 28.
For installing the endorser inkjet cartridge, see Replacing the endorser inkjet cartridge on page 28.
For installing the paper roll, see Replacing the paper roll for the printer on page 30.
Drivers and applications
There are many applications that support the RDM EC9100i and EC9600i scanners. Most are available
from third-party vendors. If you are not sure where to acquire your check scanning application, check
with whoever provided your scanner.
The drivers for RDM EC9100i series scanners are installed on your computer when you install your check
scanning application.

EC9100i and EC9600i Series Scanner User Guide Setting up your scanner
©2016 RDM Corporation Page 19
EC9600i scanning application requirements
The EC9600i series network scanners do not require that you install any drivers on your computer.
However, depending on your scanning application, there might be some additional setup required for
the application to connect to the scanner. For example, you might need to:
•Install a security certificate on your computer.
•Make changes to your browser’s security settings.
•Configure or select your scanner in the scanning application.
For more information about EC9600i setup requirements, see your scanning application’s
documentation.
Connecting the EC9600i network scanner
The EC9600i network scanner can connect to your computer via a USB cable or over the network. There
are three ways to hook up the scanner:
•Scanner and computer have separate connections to the network.
•Computer is connected to the network through the scanner. (EC9603f, EC9604f, EC9607f, and
EC9608f only.)
•Scanner is connected to the computer using USB.
Option 1: Scanner and computer have separate connections to the network
To hook up:
1. Plug an Ethernet cable into one of the Ethernet ports on the back of the scanner (marked in red
below).
2. Plug the other end into an Ethernet network jack.

EC9100i and EC9600i Series Scanner User Guide Setting up your scanner
©2016 RDM Corporation Page 20
In this setup, the scanner connects to the network using an Ethernet cable. You need to have an
Ethernet network jack available for the scanner. That means that if you are also connecting your
computer into the Ethernet network jack, you will need two Ethernet network jacks.
This setup allows multiple workstations to access the scanner.
Option 2: Computer is connected to the network through the scanner
Note: This setup option requires two Ethernet ports and so is only supported on EC9603f, EC9604f,
EC9607f, and EC9608f scanners.
In this setup, you connect the scanner to the network. You then connect your computer to the network
through the scanner.
To hook up:
1. Disconnect the Ethernet cable that is plugged into your computer and connect it to the scanner
in one of the two Ethernet ports (marked in red below).
2. Using the Ethernet cable that is included in your scanner box, connect one end to the Ethernet
port on the back of your scanner (marked in red below) and the other end into the Ethernet port
on your computer.
Like option 1, this setup allows multiple computers to use the scanner, but it requires only one Ethernet
jack for both the scanner and your computer.
Note: The computer that is connected to the network through the scanner is limited to a 100MB/s
connection.