Reaim BY01-HBE User manual

ELECTRIC PRESSURE WASHER
INSTRUCTION MANUAL
WARNING: Do not use the appliance without reading the instruction manual.

-1-
CONTENT
3. PRODUCT OVERVIEW
1. Water inlet coupling
2. Electrical plug
3. Water outlet
4.
Switch
5.
Nozzle storage
6.
Wheel
7. High pressure hose
8. Trigger gun
9. Trigger lock
10. Lance
11. Adjustable nozzle
12. High pressure detergent bottle
13. Turbo nozzle (optional)
14. Angle nozzle (optional)
15. Brush (optional)
1. APPLICATION
Your electric pressure washer has been
designed for outdoor cleaning.
Cleaning of: machines, vehicles,
structures, tools, facades, terraces,
gardening tools…
WARNING: Read this manual and
general safety instruction carefully
before using the appliance, for your
own safety. Your power tool should
only be passed on together with these
instructions.
16. Patio Cleaner (optional)
2. TECHNICAL DATA
Mo
Brush
Max. pressure
1500PSI
Max. flow
1.50GPM
Current
11A
Voltage
120V/60 Hz
Max. water
temperatur
e
40°C
Chapter
Page
1.Application
1
2.Technical data
1
3. Product overview
1
4. Safety instructions
2
5. Operating instructions
4
6. After use instructions
7
7. Environmental protection
7
8. Maintenance, cleaning, repair
7
9. Trouble shooting
9
10. WEEE - Waste of electric and
electronic equipment
10
11. Warranty
10

-2-
4. SAFETY INSTRUCTIONS
• The appliance is designed solely for
outdoor private use and NOT for
commercial use. Please keep it
away from heat, direct sunlight,
moisture and rain, frost and sharp
edges.
• Do not let people who have not
been trained in the use of a high
pressure washer nor read the
instruction manual operate the
machine!
• Electric pressure washers shall not
be used by children or untrained
personnel.
• Children should be supervised to
ensure that they do not play with
the appliance.
• Before starting up your machine
please check it carefully for any
defects. If you find any, do not
start up your machine and contact
your local distributor.
• Check especially the insulation of
the electric cable should be
faultless and without any cracks. If
the electric cable is damaged, an
authorized local service centre
should replace it.
• WARNING: High pressure jets can
be dangerous if subject to misuse.
The jet must not be directed at
persons, live electrical equipment
or the appliance itself.
• WARNING: Do not use the appliance
within range of persons unless they
wear protective clothing.
• Do not direct the jet against
yourself or others in order to clean
clothes or foot-wear.
• Hold the spray lance firmly with
both hands.
• The operator and anyone in the
immediate vicinity of the site of
cleaning should take action to
protect them from being struck by
debris dislodged during operation.
• Wear goggles and protection clothes
during operation.
• WARNING: This appliance has been
designed for use with pressure
washer detergent only.Using
other cleaning products or chemical
products may affect the safety of
the appliance.
appliance.
• Disconnect from electrical power
supply before carrying out user
maintenance.
• To ensure appliance safety, use
only original spare parts from the
manufacturer or approved by the
manufacturer.
• Do not use the appliance if a supply
cord or important parts of
appliance are damaged, e.g. safety
device, high pressure hose and
trigger gun.
• Do not use the appliance with wet
hands. If the appliance is humid or
wet, unplug it immediately. Do not
put it in water.
• Tires and tire valves may be
damaged by the high-pressure jet
and then burst.
• Never use the machine in an
environment where there could be
a danger of explosion.
• It is not allowed to clean asbestos-
containing surfaces with high
pressure.
• This Electric pressure washer must
not be used at temperatures below
0°C
• WARNING: High pressure hoses,
fittings and couplings are important

-3-
for the safety of the appliance. Use
only hoses, fittings and couplings
recommended by the manufacturer.
• WARNING: Inadequate extension
cables can be dangerous. Cables on
reels should always be completely
unwinded to prevent the cable from
overheating.
• If an extension cable is used, the
plug and the socket must be
waterproof and comply with the
below-mentioned requirements for
length and cable dimensions.
• 1.0mm² max. 12.5m
• 1.5mm² max. 20m
• If the electric cable is damaged, it
must be replaced by the
manufacturer or his service agent
or similarly qualified person in
order to avoid a hazard.
MAINS POWER CONNECTION
The following should be observed when
connecting the electric pressure
washer to the electric installation:
• The electric supply connection shall
be made by a qualified electrician
and comply with IEC 60364-1
• It is recommended that the electric
supply to this appliance should
include either a residual current
device that will interrupt the supply
if the leakage current to earth
exceeds 30 mA for 30 ms.
WATER CONNECTION
• Connection to the public mains
according to regulations.
• Inlet hose can be connected to the
water mains with a max. inlet
pressure of 10 bars.
This high pressure washer is
in Europe only allowed to be
connected with the drinking
water mains, when an appropriate
mains backflow preventer has been
installed, Type BA according to EN
1717. The length of the hose between
the backflow preventer and the high
pressure washer must be at least 10
metres to absorb possible pressure
peaks (min diameter ½ inch).
Operation by suction (for example
from a rainwater vessel) is carried out
without backflow preventer.
As soon as water has flown through the
BA valve, this water is not considered
to be drinking water any more.
IMPORTANT!
Only use water without any impurities.
If there is a risk of sand particles in the
inlet water (i.e. from your own well),
an additional filter should be mounted.
SAFETY DEVICES
• The unloader valve can reduce
pressure if it exceeds pre-set values.
• Locking device (12) on trigger gun
(11) (see illustration at the
beginning of this manual): The
trigger gun (11) features a locking
device (12). When the knob is
activated, the trigger gun (11)
cannot be operated.
THERMAL SENSOR
A thermal sensor protects the motor
against overloading. The machine will
restart after a few minutes when the
thermal sensor has cooled.

-4-
5. OPERATION INSTRUCTIONS
5.1 Mounting of wheels
Click the wheels (6) into the machine
5.2 Mounting of Patio Cleaner
1. Insert the extension lance into to
the housing
2. Fix the extension lance with the
two screws to the housing
3. Insert the rotor arm into the
extension lance
4. Insert the U-pin to fix the rotor arm.
NOTE: Make sure the rotor arm is
properly fixed to the extension
lance with the U-pin
5.3 Connection of garden hose
1. Screw the water inlet coupling (1)
tight on to the water inlet
Note: The inlet filter must always
be fitted in the water inlet pipe to
filter out sand, lime stone and
other impurities as these will
damage the pump valves.
Caution: Failure to fit the filter
will invalidate the guarantee.
2. Connect the garden hose with a
standard quick coupling
5.4 Mounting of high pressure hose
1. Attach the high pressure hose (7) to
the trigger gun (8) and machine.
2. Detach the high pressure hose by
pressing the pawl (A) or button (B)
A
B

-5-
5.5 Mounting of lance and nozzle 5.7 Start/stop of the machine
1. Push the lance (10) into the trigger
gun (8)
2. When inserted turn it.
Caution: Make sure the lance (10) is
properly fixed to the gun (8)
3. Attach the nozzles (11-16).
Caution: When attaching the nozzle
(11-16) the button (A) on the nozzle
(11-16) should come out again.
Check before activating the trigger
that the nozzle (11-16) is properly
fixed.
5.6 Water connection
IMPORTANT! Only use water without
any impurities. If there is a risk of sand
particles in the inlet water (i.e. from
your own well), an additional filter
should be mounted.
1. Let the water run through the water
hose before connecting it to the
machine to prevent sand and dirt
from penetrating the machine. Note:
Check that the filter is fitted in the
water inlet pipe and that it is not
clogged up.
2. Connect the water hose to the
water supply by means of the quick
connector (inlet water, max.
pressure: 10 bar, max. temperature:
40°C).
3. Turn on the water.
The trigger gun (8) and lance (10) is
affected by a thrust during operation -
therefore always hold it firmly with
both hands.
IMPORTANT: Point the nozzle at the
ground.
1. Check that the machine is in
upright position. NOTE: Do not
place the machine in high grass!
2. Release the trigger lock (9)
3. Activate the trigger of the trigger
gun (8) and l et the water run until
all air has escaped from the water
hose.
4. Press the Start/stop switch (4).
5. Activate the trigger of the trigger
gun (8).
6. Always adjust the distance and thus
the pressure of the nozzle to the
surface, which is to be cleaned.
Do not cover the machine during
operation or use it in a room without
adequate ventilation!
NOTE: If the machine is left or not
used for 5 minutes, it must be
switched off on the start/stop switch
(4) "O":
1. Press the start/stop switch (4) "O".
2. Disconnect the electrical plug (2)
from the socket.
3. Shut off the water supply and
activate the trigger of the trigger
gun (8) to relieve the machine of
pressure.
4. Lock the trigger gun (9)
When releasing the trigger of the
trigger gun (8), the machine
automatically stops. The machine will
2
A
1
3

-6-
start again when you re- activate the
trigger gun (8)
5.8 Adjustable Nozzle
The pressure can be adjusted by
turning the adjustable nozzle (11).
WARNING: Do not do this under
operation to avoid that the hand hits
the jet.
5.10 Angle Nozzle (optional)
The angle nozzle (14) can b e used for
many applications e.g. cleaning the
underbody of a car, underneath a lawn
mover without being splashed back
with debris, etc.
After attaching the angle nozzle (14) ,
be aware of the moment on the lance
trigger gun (8) and lance (10) as the
jet is coming out perpendicular to
these.
5.9 High pressure detergent bottle
5.11 Patio Cleaner (optionalÿ
The patio cleaner is a powerful
accessory for cleaning patio, driveways,
etc.
1. Unscrew the container (A) from the
high pressure detergent bottle (12).
2. Add detergent to the container (A)
and screw the container to the high
pressure detergent bottle (12)
3. Adjust the amount of detergent
with the button (B)
4. Foam equipped quick connector.
Press (C), then insert into the gun.
Caution: When attaching the
detergent bottle, the button (C)
should come out again. Check
before activating the trigger that
the nozzle is properly fixed.
The patio cleaner is a powerful
accessory for cleaning patio, driveways,
etc.
1. Insert the extension lance (A) into
to the housing (B).
2. Fix the extension lance (A) with the
two screws to the housing (B).
3. Insert the rotor arm (C) into the
extension lance.
4. Insert the U-pin (D) to fix the rotor
arm (C).
NOTE: Make sure the rotor arm (C) is
properly fixed to the extension lance
(A) with the U-pin (D).
NOTE: Do not use the Patio Cleaner
(16) as a broom but let it surf smoothly
over the surface.
B
C
A

6. AFTER USE INSTRUCTIONS
The machine should be stored in a
frost-free room!
Pump, hose and accessories should
always be emptied of water prior to
storing as follows:
1. Stop the machine (press the
start/stop switch (4) “O” and
detach water hose, high pressure
hose (7) and nozzle (11-16)
2. Restart the machine (4) and
activate the trigger of the trigger
gun (8). Let the machine run until
no more water runs through the
trigger gun (8)
3. Stop the machine, unplug and wind
up hose and cable.
4. Place trigger gun (8), lance (10),
nozzles (11-16) and other
accessories in the holders of the
machine.
-7-
Should the machine by mistake be
frozen, it will be necessary to check it
for damage.
WARNING: Never start up a frozen
machine. Frost damages are not
covered by the guarantee!
7. ENVIRONMENTAL PROTECTION
Old appliances contain valuable
materials that can be recycled. Please
arrange for the proper recycling of old
appliances. Please dispose your old
appliances using appropriate collection
systems.
WARNING! Always disconnect the
electrical plug from the socket prior to
maintenance or cleaning.
To ensure a long and problem free
8. MAINTENANCE, CLEANER AND
REPAIR
C
D
B
A

-8-
working life, please take the following
advice:
• Wash out water hose, high
pressure hose, spray lance and
accessories before mounting.
• Clean the connectors of dust
and sand.
• Rinse the detergent spraying
attachment after use.
• Clean the nozzles.
Any repair should always be made in an
authorized workshop with original
spare parts
8.1 Cleaning of inlet filter
Clean the water inlet filter regularly
once a month or more frequently
according to use.
Carefully loosen the filter with a
screwdriver and clean it (see section
5.3). Check that it is intact before re-
mounting it.
The inlet filter must always be fitted
inside the water inlet pipe to filter out
sand, limestone and other impurities,
as they will damage the pump valves.
CAUTION: Failure to fit the filter will
invalidate the warranty
8.2 Cleaning of air vents
The machine should be kept clean so
as to let cooling air pass freely through
the machine vents.
8.3 Greasing of couplings
To ensure an easy connection and that
o-rings do not dry up; the couplings
should be greased regularly.

-9-
9. TROUBLE SHOOTING
Symptom
Cause
Recommended action
Machine refuses to
start
Machine not plugged in
Plug in machine.
Defective socket
Try another socket.
Fuse has blown
Replace fuse. Switch off other machines.
Defective extension cable
Try without the extension cable.
Fluctuating
pressure
Pump is sucking air
Check that hoses and connections are
airtight.
Valves dirty, worn out or
stuck
Contact your nearest service centre.
Water supply not sufficient
Increase water pressure, check for
blockage of garden hose and/or change to
bigger hose.
Pump seals worn
Contact your nearest service centre.
Machine stops
Fuse has blown
Replace fuse. Switch off other machines.
Incorrect mains voltage
Check that the mains voltage corresponds
to specification on the name plate.
Thermal sensor activated
Leave the machine for 5 minutes to cool
down.
Nozzle partially blocked
Clean the nozzle with a needle and by
spraying water backwards through the
nozzle.
Fuse blows
Fuse too small
Change to an installation higher than the
amperage consumption of the machine.
Amperage increase
Try without the extension cable.
Machine pulsating
Air in inlet hose/pump
Allow machine to run with open trigger
until regular working pressure resumes.
Inadequate supply of mains
water specifications
required
Increase water pressure, check for
blockage of garden hose and/or change to
bigger hose.
Nozzle partially blocked
Clean the nozzle with a needle and by
spraying water backwards through the
nozzle.
Water filter blocked
Clean the filter.
Hose kinked
Straighten out hose.
Machine often
starts and stops by
itself
Pump and/or trigger gun is
leaking
Contact your nearest service centre.
No water supply
Connect inlet water.
Machine starts but
no water comes
out
Water filter blocked
Clean the filter.
Nozzle blocked
Clean the nozzle with a needle and by
spraying water backwards through the
nozzle.

-10-
10. WEEE - WASTE OF ELECTRIC AND ELECTRONIC EQUIPMENT
The symbol on the product or on its packing indicates that this product
may not be treated as household waste. Instead it shall be handed over
to the applicable collection point for the recycling of electrical and
electronic equipment. By ensuring this product is disposed of correctly,
you will help prevent potential negative consequences for the
environment and human health, which could otherwise be caused by
inappropriate waste handling of this product. For more detailed
information about recycling of this product, please contact your local city office, your
household waste disposal service or the shop where you purchased the product.
11.WARRANTY
• This product is warranted for a 12 months period effective from the date of
purchase by the first user.
• Damage and/or defects resulting from inappropriate use do not fall under the
warranty provisions.
• We also disclaim all liability for any bodily injury resulting from inappropriate use
of the tool.
• At the same time, no claim can be made on the warranty if the damage of the
device is the result of negligent maintenance or overload.
• Definitely excluded from the warranty is damage resulting from fluid permeation,
excessive dust penetration, intentional damage (on purpose or by gross
carelessness), inappropriate usage (use for purposes for which the device is not
suitable), incompetent usage (e.g. not following the instructions given in the
manual), inexpert assembly, lightning strike, erroneous net voltage. This list is not
exhaustive.
• Acceptance of claims under warranty can never lead to the prolongation of the
warranty period nor commencement of a new warranty period in case of a device
replacement.
• We reserve the right to reject a claim whenever the purchase cannot be verified or
when it is clear that the product has not been properly maintained (Clean
ventilation slots, carbon brushes serviced regularly, etc.).
• Any transportation costs shall always be borne by the customer, unless agreed
otherwise in writing.
• You can always obtain more information by the email rea[email protected] or at
the number 888-899-1688.

-11-
USA Office:
101 wales avenue,Avon,MA 02322,United States
Service Hot line: 888-899-1688
Email: [email protected]m