RealFlame 705 User manual

Fireplace Assembly Instructions
Model # 705
Envision Wall Hanging Fireplace
705-Envision-SS-070512
Lot:_________
PO:_________

Warnings 3
Parts Included 4
Installation
Mounting Bracket 5
Mounting the Fireplace 6
Installing the Glass and Ventless Fuel Firebox 7
Filling the trough 8
Lighting and extinguishing the fire 9
Care and Cleaning 10
Warranty Information 11
Contents
2
Thank you for purchasing a Real Flame Fireplace.
Prior to installing or using your Real Flame® Fireplace please be sure to read all of the information
contained in this installation, operation and maintenance manual very carefully. This manual will
detail exactly how the Ventless Fuel Firebox and replace are intended to be used safely.
Failure to follow these instructions could result in property damage, bodily injury or death.
Children and pets should be kept under close supervision and a safe distance away when the Real
Flame® replace is in operation.
Building codes may require extra steps be taken to install your replace in a condo, apartment or
townhouse. Please check with local codes to make sure that every precaution is taken.
TERMS OF USE

3
WARNINGS !!
If you have questions please call customer service at: 1-800-654-1704
Read all instructions included with ventless fireplace fuel and fireplace
NOTICE: Buyer assumes all responsibility for safety and use that is not
in compliance with these instructions and warnings.
1. Read entire label and instructions before using ventless fireplace fuel.
2. Do not place fireplace in an area with lots of trac, such as a hallway or entryway.
3. Make sure fireplace is mounted correctly according to the instructions in this manual.
Failure to mount the bracket to a stud could cause the unit to detach from wall resulting in
serious injury, property damage or death.
4. Never burn trash, paper, or wood in the fireplace. Burn only Real Flame® ventless fireplace
fuel in the fireplace.
5. Keep away from children and pets. Unit is not to be operated by children.
6. Do not lean over the unit when lighting.
7. Never burn ventless fireplace fuel outside the designated burn area.
8. Do not burn more than the specified amount of ventless fireplace fuel at any time.
Overfilling may cause fuel to spread outside the designated burn area and could result in
property damage or serious injury if ignited.
9. Never leave a burning fire unattended.
10. Never move or touch unit during or immediately after burning ventless fireplace fuel. Unit
and glass will be extremely HOT. Allow surfaces to cool for 20 minutes before touching.
11. Do not wear flammable or loose clothing when operating the fireplace.
12. Never alter the unit in any manner.
13. Exercise the same precautions as you would with any open fire.
14. DEATH, SERIOUS INJURY OR PROPERTY DAMAGE may result if these warnings are not
followed correctly.
Do not attempt to add ventless fireplace fuel to a fire that is already burning.
Use only Real Flame® ventless fireplace fuel in unit. Do not use with any other
fireplace fuel or flammable material.
Do not store or use gasoline or other flammable materials, including ventless
fireplace fuel, near this product. Vapors from these types of items may collect and
increase the risk of fire, explosion or injury.
In case of an emergency use a CO2 extinguisher or baking soda to extinguish the fire.
RF wall hanging fireplace WARNINGS 030812
-
-
-
-
Using your
Fireplace
Before using unit, be sure you have read and understood the
step-by-step instructions.
After several burns, soot may develop on the inside of the glass.
Clean with a damp soapy rag or any household glass cleaner.
During the initial burn you may experience a slight odor. Odor is
temporary and will be absent on following burns.
Real Flame® Ventless Fireplace Fuel Contains Isopropyl Alcohol
Avoid contact with eyes, mucous membranes or prolonged
contact with skin. May irritate eyes. Store in a cool, dry place. Keep
away from flame, heat or items that spark. Use in well-ventilated
areas. Keep out of reach of children and pets. In case of fire, use a
CO2 fire extinguisher or baking soda.
VENTLESS
FIREPLACE
FUEL
If fuel gets in eyes, flush with water for 15 minutes; get medical
attention. If ingested, do not induce vomiting; call poison control
center or a doctor.
FIRST AID
-
-
-
RISK OF EXPLOSION

Before installation, check the list below to ensure all pieces have been included
4
123
56
07050101: Black Envision Fireplace
07050801: White Envision Fireplace
Qty: 1
OR
OR
01282402 - Scraper
Qty: 1
01282401 - Ventless Fuel Firebox
Qty: 1
01282403 - Trough
Qty: 1
4
07100004 - Glass
Qty: 1
ATTENTION
If you have any questions, issues or parts are missing,
email or call Real Flame® customer service prior to
returning to the store where this item was purchased.
STOPSTOP
In USA call: 1-800-654-1704
In Canada call: 1-800-363-6443
custserv@realflame.com
07050111 - Black Mounting Bracket
07050811 - White Mounting Bracket
Qty: 1
Qty: 14
Qty: 14
Qty: 14
A
B
C
Qty: 4
Qty: 2
Qty: 14
E
F
D
070500009- Hardware Kit Qty:1

Step one
5
Alternate method for installing the Mounting
Bracket (Figure 2):
Find a suitable location on a wall for the fireplace,
allowing a MINIMUM OF 24 INCHES of clearance in
all directions from anything flammable or combustible.
Locate a stud. At eye level drill a 1/8” pilot hole
into stud where the center of the mounting
bracket will be attached on both the top and
bottom mounts.
Using a level, mark where the next four holes will
be made 8“ to the left and right side of the two
center holes. Drill a 3/16” hole and insert a drywall
anchor into each.
Attach the mounting bracket first by the center
holes with a #10 -1¼” screw (A).
Level the mounting bracket and install the #10-1¼”
screws through the bracket and into the drywall
anchors.
Recommended method for installing the
Mounting Bracket (Figure 1):
Find a suitable location on a wall for the fireplace,
allowing a MINIMUM OF 24 INCHES of clearance in
all directions from anything flammable or
combustible.
Locate 2 studs that the centers are 16 inches
apart. Mark each at eye level. Use the Mounting
bracket (3) as a guide, level the bracket using a
bubble level and mark where to drill a 1/8” pilot
hole into both studs where the outer two holes of
the mounting bracket will be attached.
Attach the mounting bracket using four #10 - 1¼”
screws. (A)
Floor
Eye Level
Stud
Mounting
Bracket (3)
8” 8”
For mounting to a single stud:
Figure 2
Floor
Eye Level
Mounting
Bracket (3)
For mounting to two studs
Figure 1
16”
Stud

Figure 4
Step Two
Mounting the Envision Fireplace to
the bracket:
Figure 3:
Place the fireplace on the wall over the
bracket as shown. The inside of the top
should be resting on the bracket. Bracket
will fit inside of the fireplace and will not
be seen when attached.
Center the fireplace on the bracket so
that the two holes in the top and bottom
of the fireplace line up with the holes in
the bracket.
Figure 4:
Using the two 10-32 - 3/4” machine
screws (D), attach the fireplace to the bracket
at the top. Be careful not to overtighten
the screws.
Repeat with two screws on the
bottom of the fireplace.
6
Wall
Stud
Drywall
Figure 3
D
D
D
D

Figure 7
Glass
Figure 6
Figure 5
thumbscrew
Installing the glass and Ventless Fuel Firebox:
Figure 5:
Place the glass into the front of the fireplace by
sliding it down in the gap between the stainless
steel part and the painted section. There are two
clips inside that the glass will need to sit in. Make
sure that the glass is seated correctly before
proceeding.
Figure 6:
To secure the glass firmly in place, turn the
thumbscrew attached to the clip clockwise until
the glass is held vertically in place.
CAUTION: Do not overtighten thumbscrews.
Figure 7:
Note: Glass must be secure prior to installing the
Ventless Fuel Firebox.
Install the Ventless Fuel Firebox by placing it into the
open area of the Envision fireplace. When installed-
correctly the Ventless Fuel Firebox should open
towards the user.
Step Three
7

Real Flame®
Ventless
Fireplace
Fuel
Figure 8
5
6
Step Four
Filling the trough
Figure 8
The trough should have been shipped
pre-installed in the Ventless Fuel Firebox. If it
has been removed, reinstall the trough inside
the Ventless Fuel Firebox prior to filling.
NOTE: Finish filling the trough and replace
cap on the ventless fireplace fuel container
before attempting to light the unit.
Figure 9
Fill the trough inside the Ventless Fuel Firebox
to the top of the post or 3/4” from the lip of
the trough.
Cleanup any spilled fuel before lighting.
Figure 9
8
WARNING: RISK OF EXPLOSION
• Do not attempt to add ventless fireplace fuel to a fire that is already burning.
• Use only Real Flame® Ventless Fireplace Fuel. Do not use with any other fireplace fuel or
flammable material.
• Do not store or use gasoline or other flammable materials, including ventless fireplace fuel, near this
product. Vapors from these types of items may collect and increase the risk of fire, explosion or injury.
• In case of an emergency use a CO2 extinguisher or baking soda to extinguish the fire.

Figure 11
Figure 10
Step Five
Lighting and Extinguishing the Fire
To Light (Figure 10)
Open the sliding damper with the hook end of
the scraper as shown.
Use an extended lighter or fireplace match to
light the ventless fireplace fuel.
To Extinguish (Figure 11)
Close the sliding damper with the hook end of
the scraper as shown.
Leave closed for 10-20 seconds before
attempting to re-open or lift open lid.
Warning: Do not attempt to refill the
through immediately after burning. Allow
20 minutes for unit to cool before refilling.
9
Warning: Ventless Fuel Firebox insert,
glass and surround will be extremely hot.
Use caution when attempting to close the
damper.
!
!

Trough should be cleaned every two burns. This can be cleaned
using the scraper tool included.
- Allow trough to cool completely before attempting to clean.
- Place the straight edge of the scraper into the trough and pull
along the edge.
- Residue should be thrown away in the trash.
To get the trough out of the Ventless Fuel Firebox, use the scraper
tool’s hook end to open the lid of the Ventless Fuel Firebox using
Open the lid by lifting up and towards the front as shown in
Lift the trough out with the hook end of the scraper tool using
the post in the center of the trough.
Use a soft damp cloth and a standard dish soap to clean the body
of the Envision.
Any standard glass cleaner can be used to clean the glass.
Use stainless steel cleaner or polish to clean the stainless parts.
Discoloration is normal for stainless steel that is in direct contact
with the ame.
Care and Cleaning
Figure 12
Figure 13
Figure 14
10
gure 13.
the small cutout towards the back as shown in gure 12.