RealFlame 2085 User manual

Fireplace Model # 2085
Instruction Manual
®

Rev. 06/04/07
Using your Fireplace
- Follow all instructions included with gel fuel before use.
- Before using Fireplace make sure you have read and understand the step-by-step instructions.
- During the initial burn you may experience a slight odor. This odor is temporary and will be absent on following burns.
Instructions and warnings for use
Welcome to the Real Flame® family of gel fuel products. If you have any questions
please call customer service at 1-800-654-1704 or log on to www.REALFLAME.com.
WARNINGS !!
NOTICE: Buyer assumes all responsibility for safety and use that is not
in accordance with instructions and warnings.
1. Fireplace is designed to be used with Real Flame®gel fuel only. Do not use with any other gel fuel or any other flammable
liquid or gel.
2. Read entire label and instructions before using Real Flame gel fuel.
3. Make sure fireplace is set on a flat, level and stable surface. Keep fireplace stable at all times.
4. Make sure fireplace and gel fuel are burned on a flat and level surface.
5. Never leave a burning fire unattended, especially around children or pets.
6. Fireplace is not to be operated by children. Keep away from children and pets.
7. Exercise the same precautions as you would with any open fire.
8. When in use some surfaces will be hot, use caution.
9. Never touch logs, gel fuel cans or any other metal surfaces during or immediately after burning gel fuel. They will be extremely
 HOT. Allow them to cool for 60 minutes before touching.
10. Do not burn more than three cans of fuel at once.
11. Do not place more than 15 lbs. of weight on the top of the fireplace at anytime.
12. Do not alter fireplace, metal firebox or log set in any manner.
13. Keep fireplace and gel fuel cans away from flammable materials at all times.
14. Do not store or use gasoline or any other flammable vapors, liquids, or materials in the vicinity of fireplace and gel fuel.
15. Do not wear flammable or loose clothing when operating the fireplace.
16. Do not move fireplace while in use. Do not attempt to move or store the fireplace until 60 minutes after gel fuel cans have
been extinguished.
17. Do not burn trash, paper, or wood in the fireplace. Burn only Real Flame®gel fuel in the fireplace.
18. Do not burn gel fuel outside designated burn areas on the metal grate.
19. Do not put fireplace in an area with lots of traffic, such as a hallway or entryway.
20. In case of an emergency use a CO2 extinguisher to extinguish the fire.
21. Death, serious injury or damage to property may occur if the warnings above are not followed.
22. If for any reason you cannot follow these warnings please call us at 1-800-654-1704.
®
®
STOP!
If parts are missing or damaged, call 1-800-654-1704 for assistance

Step One
Figure 1
-Set the Base (1) on a flat, carpeted surface.
-Set the Left and Right Side Panels (2 & 3)
upright. Wood mounting blocks will be at
the tops and front edges of the panels.
-Insert the Panels into the Base at the outer
edges of the cutout in the Base with
finished sides facing out. Attach each to
the Base with 2 screws.
-Align Left Trim Panel (4) with Left Side
Panel (2) using the tongue and groove
edge as a guide and slide all the way to
the Base. Screw together through
mounting blocks on Side Panel.
-Repeat using Right Trim Panel (5) and
Right Side Panel (3).
Number Description Part Number Quantity
1 Base 2001 1
2 Left Side Panel 2002 1
3 Right Side Panel 2003 1
4 Left Trim Panel 2004 1
5 Right Trim Panel 2005 1
6 Center Panel 2006 1
7 Mantel Top 2007 1
8 Front Cross Trim 2008 1
9 Left Marble Facing 2086 1
10 Right Marble Facing 2087 1
11 Top Marble Facing 2088 1
12 Left Mantel Support 2012 1
13 Right Mantel Support 2013 1
not shown
Firebox Clips 1075 2
1" Wood Screws 9713 Bag
Parts List
Rev. 10/07
Figure 1
1
23
45
2085 Brickwood Insructions ®
Before assembly, locate instructions and
hardware. take out all parts and compare
them to the photograph and the assembly
illustrations. Be sure you have all parts
identified.
Check for screws that are wrapped in the
packaging to be sure you dont discard
them. You may have extra screws.
A helping hand is always good.
Assemble the fireplace with an adult
assistant if possible.
The cement log is heavy. Put the
fireplace in the desired location before
inserting cement log.
Use caution not to over tighten screws.

Step Two
Figure 2
-Attach Left and right Mantel Supports (12
& 13) to tops of Trim Panels by inserting
dowel at top of Trim Panels into hole in
back of Mantel supports.Secure with screws
through holes in back of Trim Panels.
-Set Wood Facing (8) between Trim Panels
at floor level so mounting blocks on Facing
are behind Trim panels. Attach Facing to
Trim Panels through holes in Facing
mounting blocks.
-Insert Center Panel (6) between Trim
Panels by sliding tongues at outer edges of
Center Panel into grooves at inner edges of
Trim panels and pressing down so top
edges align. Attach Center Panel to Trim
Panels with screws through mounting
blocks at outer edges of Center panel.
-Align Left and Right Mantel Supports (12
& 13) with pre-drilled holes in Center
Panel. Note that holes are offset. Screw
Mantel Supports into place.
-Insert Top Brick Facing (11) into opening
below Center Panel. Screw Facing to the
Center Panel through attached mounting
blocks at sides and top.
Step Three
Figure 3
-Insert Left Brick Facing (9) into opening
next to Left Trim Panel. Screw Facing to
Trim Panel through attached mounting
blocks at sides, top and bottom.
-Repeat with Right Brick Facing (10) and
Right Trim Panel. The facings should sit
flush up against each other.
-Slide Mantel Top (7) onto top of unit.
Screw Mantel Top to unit using screw
holes in Center Panel and in mounting
blocks at top of Side Panels.
Figure 3
14
Rev. 10/07
15
16
910
7
Figure 2
6
12 13
11
8