RealFlame Corretto 1340E User manual

40” Corretto Wall-Mounted Fireplace
English • Français • Español
Model # 1340E
Lot:____________
PO:____________
© 2020 KSP Group, Inc.

2
TABLE OF CONTENTS
PARTS LIST
Parts List
Important Safety Instructions
Site Selection and Preparation
Installation
Operation and Features
Care and Maintenance
Warranty
Return
Ownership Registration
2
3
5
6
12
15
16
17
53
1 Remote control 13400001 1
2 Crushed glass 13300004 1 Box
3 Stone Filler 13400003 1 Box
4 Mounting Bracket 13400004 1
5 Mounting screws 12
6 Glass front panel 13400106 1
A 1
2
B
4
NOTE
Tools required: level, electric drill, drill bits [8mm (5/16in)], Phillips screwdriver,
hammer, safety goggles and gloves.
x4
x4
6
Hardware Kit - 13400007
Part Name Part No. Qty. Part Name Part No. Qty.
5
(Note: Attached to the firebox)
(Note: Attached to the firebox)
Cx4
3

3
SAVE THIS USER’S GUIDE FOR FUTURE REFERENCE
When using electrical appliances, basic precautions should always be followed to reduce the
risk of fire, electric shock, injury or death.
Read all instructions before installing or using this fireplace
1. Electric fireplace is for indoor use only.
2. Do not modify the electric heater in any way. Use it only as described in this manual.
Any other use not recommended by Real Flame may cause a fire, electric shock,
serious injury or death.
3. The heater may become hot when in use and could burn you. To avoid burns, do not
let bare skin touch hot surfaces. Keep combustible materials, such as furniture,
pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9m) from the top,
sides and rear of the unit.
4. Always use properly grounded, fused and polarized outlets.
5. Always call a certified electrician if new circuits or outlets will be required.
6. Extreme caution is necessary when any heater is used by, or near, children or
people with disabilities. The unit should never be left unattended.
7. The electric heater is not intended for use in bathrooms, laundry areas and similar
indoor locations. Never locate heater where it may fall into a bathtub or in other areas
where it may come into contact with water; dangerous electric shock could occur.
8. Do not operate any unit with a damaged cord or plug, or if the heater has
malfunctioned, or if the fireplace has been dropped or damaged in any
manner. Contact Real Flame at 1-800-654-1704.
9. The cord may become hot when the fireplace is in operation. Do not run the cord
under carpeting, furniture, or appliances. Do not cover cord with throw rugs, runners,
or similar items.
10. To prevent people from tripping on the cord, make sure it is placed away from high
trac areas.
11. Do not insert or allow foreign objects to enter any ventilation or exhaust opening
as this may damage the heater or result in electric shock.
12. To prevent a possible fire, do not block air intake or exhaust in any manner. Do not
use on soft surfaces, like a bed, where openings may become blocked.
13. All electrical heaters have hot, arcing or sparking parts inside. Do not use in areas
where gasoline, paint, or flammable liquids are used or stored or where the unit will
be exposed to flammable vapors. Doing so could result in a fire or cause an explosion.
14. Do not burn wood or other materials in the electric heater; the unit or the wall could
catch fire if you do.
15. To disconnect the unit, turn the firebox o and then remove the plug from the
outlet.
16. Always unplug the electric heater when not in use for an extended period of time.
IMPORTANT SAFETY INSTRUCTIONS
Glass Panel Information
1. The panel is made of tempered glass.
2. Under no circumstances should this product be operated with a broken or
chipped glass panel.
3. Do not hit or slam the glass.
4. Do not use abrasive cleaners to clean the glass.

4
•Risk of electric shock
•Do not open
•Non-user serviceable parts inside
WARNING
SAVE THESE INSTRUCTIONS
DESCRIPTIONS OF WARNINGS
NOTE Procedures and techniques that are considered important
enough to emphasize.
CAUTION Procedures and techniques which, if not carefully followed,
will result in damage to the equipment.
WARNING Procedures and techniques which, if not carefully followed,
will expose the user to the risk of fire, serious injury, illness or
death.
NOTE This equipment has been tested and found to comply with the limits for Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference with radio or television reception. That can be determined by turning
the equipment o and on. The user is encouraged to try to correct the interference
by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and the receiver.
•Connect the equipment into an outlet on a circuit dierent from that to which
the receiver is connected.
•Consult the dealer or an experienced radio / TV technician for help.
Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may
cause undesired operation of the device.
NOTE A 15amp, 120-volt circuit is required. A dedicated circuit is preferred but
not essential in all cases. A dedicated circuit will be required if, after installation,
the circuit breaker trips or the fuse blows on a regular basis when the heater is
operating. Additional appliances on the same circuit may exceed the current rating
of the circuit breaker.
If you have any questions about our products please contact Real
Flame® customer service at 1-800-654-1704
IMPORTANT SAFETY INSTRUCTIONS (Cont’d.)
!
!
!
!
!
!

5
SITE SELECTION AND PREPARATION
To reduce the risk of fire or electric shock when installing:
• Make sure the power cord is not pinched or against a sharp edge when installed.
•Ensure that the power cord is stored or secured to avoid tripping or snagging.
•Construction and electrical outlet wiring must comply with local building codes
and other applicable regulations.
•Do not attempt to wire your own new outlets or circuits. Always call a licensed
electrician.
See figure 1 for grounding instruction.
This heater is for use on 120 volts.
The cord has a plug as shown at A in
Figure 1. An adapter as shown at C is
available for connecting three-blade
grounding-type plugs to two-slot
receptacles. The green grounding lug
extending from the adapter must be
connected to a permanent ground
such as a properly grounded outlet
box. The adapter should not be used
if a three-slot grounded receptacle is
available.
WARNING
Fig. 1
METAL SCREW
GROUNDING PIN
*ADAPTER
NOTE: This adapter is
prohibited in Canada.
NOTE: This adapter is
prohibited in Canada.
GROUNDING
MEANS
COVER OF GROUNDED
OUTLET BOX
GROUNDING PIN
Manual Reset
To manually reset the firebox, unplug power cord, wait 15 seconds and plug back
into the wall outlet.

INSTALLATION
WARNING This appliance is designed to be fixed to a wall at a minimum height of
12 in (300mm) and at a minimum distance of 39in (1000mm) from the top of the
heater to the ceiling. The wall bracket must be fitted horizontally with the cable
routed to the bottom right of the fireplace.
NOTE A distance of 23.62in (600mm) from the base of the fireplace to the floor is
recommended for the best view of the fireplace.
NOTE Two people are required for installation.
6
17.7” (450 mm)23.6” (600 mm)
Floor
Step 1: Place the fireplace on a padded surface. Unscrew the 4
mounting screws on the top and 2 mounting screws on each side of
the fireplace (see Fig. A ). Set these screws to the side.
Fig. A
40” (1016 mm)

7
INSTALLATION (Cont’d.)
Fig. B
Step 3: The mounting bracket is fixed on the back of the fireplace.
Unscrew 2 screws and remove the bracket. See Fig. C.
Fig. C
Step 2: Remove the front glass as shown in Fig B. Handle it with care.
11
2
2
2

8
Step 5: For the holes that do not hit a stud, drill holes 5/16in(8mm) and use the supplied
wall anchors. Install the wall anchors into the holes and gently tap them into place with a
hammer until the flange of the wall anchor is flush with the wall surface. See Fig. E.
INSTALLATION (Cont’d.)
Mounting the Firebox Bracket
Fig. E
Drill 1/16” pilot hole
Install into wall stud
Step 4:
• Locate studs where the firebox will be mounted.
• Following the height diagram on page 6, mark the location on a stud and drill a 1/16”
pilot hole for mounting the bracket to a wall stud. One stud is required to safely
mount this bracket using either of the holes in the center of the mounting
bracket (3).
• Attach the mounting bracket to the wall using one screw.
• Level the bracket and mark the remaining hole locations.
• Install remaining screws to finish mounting the bracket (3).
Wall stud
Fig. D
A
A
A
C
3
C
C
B B
56mm

9
Step 7: Mount the fireplace on the wall using the slots of the metal bracket
at the back of the fireplace. See Fig. G. Make sure that the mounting
bracket is completely engaged into the metal bracket at the back of
the fireplace.
Fig. G
Step 6: Secure the mounting bracket to the wall anchors using the anchors
and screws as shown in Fig. F.
INSTALLATION (Cont’d.)
A
A
C
C
3
Fig. F

10
Step 8: Secure the mounting bracket to the fireplace using 2 mounting
screws. See Fig. H.
Step 9: Put the crushed glass or stone filler onto the shelf panel
of the fireplace. See Fig. I.
Fig. H
Fig. I
INSTALLATION (Cont’d.)
4
4
4
2