Reflecta Super 8 User manual

Quick Installation Guide
Super 8 Roll Film Digitizer

COMPONENTS
Front (Figure 1):
1) Supply Reel (Arm)
2) Take-up Reel (Arm)
3) Feed Sprocket
4) Forward Button
•Press briefly (1 sec)—feeding frame one by one,
•Press and hold (more then 3 seconds)--- Continuously
feeds the frames
5) Stop Button
6) Rewind Button
•Press briefly (1 sec)— feeding frame one by one,
•Press and hold (more then 3 seconds) ---
Continuously feeds the frames
7) Film Rollers
8) Film Cleaner
9) Power Button
Back (Figure 2):
10) DC power
11) USB 2.0 port
5) Stop Button
6) Rewind Button
9) Power Button
7) Film Rollers
4) Forward Button
Figure 1
Figure 2
11) USB 2.0 port
10) DC power
3
2) Take-up Reel (Arm)
3) Up Feed Sprocket
8) Film Cleaner
1) Supply Reel (Arm)
3) Down Feed Sprocket

Super 8 scanner Quick guide
Before Installing Scanner
Check your Super 8 Film Reel, Film and Hard Disk
Space
Film Reel :
Super 8 Scanner support 1”~8” standard Super 8
film reel
Film:
1. Please make sure your film is smooth, if not
please use cutter to repair and maintain to
smooth (Fig 1, 2)
2. If your film is splicing, please check as below
list before you insert film
•splicing parts and film hold are smooth
•The cement is fully dry
or will damage super 8 scanner
3. Please use special solvent with Super 8 Scanner
or will damage your film.
Reel Type Super 8 Film at
18 frames
/second
Super 8 Film at
24frames
/second
Hard Disk Space
50 feet
(15 meters) 3.5 min 2.5 min 1 GB (0.45 GB
for movie)
200 feet
(60 meters) 13 min 10 min 4 GB (1.8 GB for
movie)
300 feet
(90 meters) 20 min 15 min 6 GB (2.7 GB for
movie)
400 feet
(120 meters) 26 min 20 min 8 GB (3.6 GB For
movie)
600 feet
(180meters) 40 min 30 min 12 GB (5.4 GB
movie)
Hard Disk Space:
○хх○хх
Fig. 1 Fig. 2

Super 8 scanner Quick guide
Calibration Light Source (First time use)
Open the Case
Turn on Power
Connect to USB to PC
Wait for LED light to turn Orange
Activate the
CyberView S8
Software
1
2
3
4
5
6
7
Create a New Movie Plan
and click “Next” button
click “Calibration” button
After Finish Calibration
click “OK” button

Super 8 scanner Quick guide
Install Super 8 Scanner
Open the Case
Open the Reel Arm
Install movie film reel to Supply
Reel Arm and Take-up Reel Arm
Turn on Power
Install film to Super 8 Scanner
(Please see “How to install film”)
Connect to USB to PC
Wait for LED light to turn Orange
Activate the
CyberView S8
Software
Start to Digitize Your
Super 8 Movie
1
2
3 4
5
6
7
8
9
Make Sure the Reel is
securely installed

Super 8 scanner Quick guide
How to install film to Super 8 Scanner
Turn on Power
Install movie film reel to Supply Reel
Arm and Take-up Reel Arm
Press and hold Forward Button
Feeding film into Up Feed
Sprocket
Film auto feeds out from
Down Feed Sprocket
Feeding film into the Film Rollers
Feeding film into the Take-up
Reel
Click Stop Button
Start to Digitize Your
Super 8 Movie
1
2
3
4 5
6
7
8
Feed Direction
Film Hold Lock your film onto the Take-up
Reel
Push Locked
Press the Forward Button until film
is rolling tight then press Stop
Button
9
Scroll film until a sufficient length
to Take-up Reel then press Stop
Button

Super 8 scanner Quick guide
How to clean your film with Super 8 Scanner
Turn on Power
Install movie film reel to Supply
Reel Arm and Take-up Reel Arm
Press and hold the Forward
Button Feed Film through the wool felt
Click Clean
Button to start
cleaning your
film
1
2
3
Open the cover of the
Film Cleaner
Add cleaning solvent to
Wool Felt
4
5
6
Feeding film into the Take-up Reel
Click Stop Button
Activate the
CyberView S8
Software
7
8
9
10

Installing the CyberView S8 Software
1. Install the CyberView S8
2. Connect the USB to the PC
3. Push the Power Button to turn the unit on
4. Install film to S8 Digitizer
5. Open the CyberView S8
Create a new movie
1. Choose “Create Your Movie Plan name”
2. Type the plan name
3. Choose the default export folder
4. Click the “Start Your Plan” to start digitizing
Continue an existing movie plan
1. Choose “continue movie plan”
2. Browse to the existing folder and choose ”plan.ini “
3. Click the “Start Your Plan” to continue digitizing
CyberView S8 Software Quick guide

Capture interface
1. Check the preview window
2. Click “up” and “down” to check your first
capture frame
3. Click “Capture” to start digitizing S8 movie
4. After you finish digitizing the S8 movie, the
software will auto stop capture (this is not the
last step in the process)
5. Click next to watch your movie
Preview Widow
Frame Control button
Capture Button
Digitized frame counting Relapsed time
CyberView S8 Software Quick guide
Auto Brightness
Brightness
adjustment bar
Calibration
Auto Contrast

Combine interface
1. Check the preview window
2. Choose your super 8 movie frame rate(18 or 24
frame rate/ sec)
3. Click apply button to preview digitized frames
4. Choose output size “1080p” or “720p”
5. Click “Combine” to transfer frame to movie
6. After finishing the movie transfer, you can click “see
your movie” to watch digitized super 8 movie
Preview Widow
Output Size
Combine
Frame Rate
CyberView S8 Software Quick guide
Watch Video

Advanced Setting
More detail operation function, setting and troubleshooting please check user manual (in Cyberview
S8 CD) or go to reflecta website www.reflecta.de
CyberView S8 Software Quick guide