Regalo 2250 User manual

www.regalo-baby.com
Regalo International, LLC.
3200 Corporate Center Drive, Suite 100 / Burnsville, MN 55306, USA
866.272.5274 (U.S. only) or 952.435.1080
Made in China
Swing Down Double-Sided
Bed Rail
OWNER’S MANUAL MODEL: 2250, 2250CA
• READ ALL INSTRUCTIONS BEFORE ASSEMBLY AND USE OF BED RAIL.
• KEEP INSTRUCTIONS FOR FUTURE USE.
Click here to view detailed product descriptions and prices.
Call 800-397-5899 to order today!

English 3
Before Using Product
Read and follow all instructions carefully to ensure that your product is properly
installed. Failure to follow these instructions for the assembly of use of your bed rail
could result in serious injury or death. The safety of your child is your responsibility.
Please keep these instructions for your reference.
WARNING
• SUFFOCATION AND STRANGULATION HAZARD
• Gaps in and around bed rails have entrapped young children and
killed infants.
• NEVER use with children younger than 2 years old. USE ONLY with
older children who can get in and out of adult bed without help.
NEVER use in place of crib.
• NEVER use unless bed rail is tight against mattress, without gaps,
and at least 9 in. from headboard and footboard. Do not fill gaps
with pillows, blankets, or other items that can suffocate children.
• NEVER use on toddler bed, bunk bed, water bed, or bed with
inflatable mattress. Use ONLY on adult bed.
• Use ONLY on a bed ranging from twin size to queen size.
•Use ONLY on adult bed with box spring and mattress.
• This bed rail is NOT recommended to be used on a platform
or similar style bed.
• This bed rail is intended for use with children 2 years to
5 years of age.
• Discontinue use if damaged, broken, or if parts are missing.
•Do not use if bed rail is not fully assembled.
•Periodically check that all spring pins are fully engaged on bed rail
support bars.

English4
PLEASE CHECKTO MAKE SUREYOU HAVE THE FOLLOWING PARTS:
A Mesh Wall (2)
B Right Upper Support Bar (2)
C Left Upper Support Bar (2)
D Right Bottom Support Bar (2)
E Left Bottom Support Bar (2)
F Right Swing Lock and Strap Assembly (1)
G Left Swing Lock and Strap Assembly (1)
Before Assembly
A
BF
C
D
E
G
D
E
C
B

English 5
AssemblingYour Bed Rail
NOTE: Make sure that the spring pins are secured into the opposing holes
so that the bed rail cannot pull apart.
STEP 1
Insert the left upper support bar into the left bottom support bar. Make sure
the spring pin fits securely into the opposing hole so that the two pieces
cannot pull apart. Repeat on the right side of the bed rail.
STEP 2
With the left and right sides of the bed rail assembled, connect the two sides.
SECURED
SPRING
BUTTON
SPRING
PIN

English6
NOTE: If the zipper does not close securely, make the necessary adjustments
to ensure proper closure. DO NOT use the bed rail without securely zipping the
mesh wall properly.
STEP 3
To install the mesh wall on the bed
rail, slide it over the frame until
it reaches the other end, zip it
shut, then attach the velcro strap
over the zipper to complete the
installation.
Repeat STEPS 1 – 3 to assemble
the second side of the
double bed rail.
Pull straps to tighten Latch Closed
Latch Open Swung Down

Pull straps to tighten Latch Closed
Latch Open Swung Down
English 7
NOTE: Each set of corner hinges is permanently connected by an anchoring
strap. On one side of each set, the strap is adjustable. The adjustable sides
should be mounted to the same side wall assembly.
STEP 4
With the wall of the bed rail
completely assembled, you will
now connect the left and right
swing lock and strap assemblies.
STEP 5
Insert one side of the wall frame into one of the leg pieces. Press in the metal
spring button to fully insert the tube into the hole in the plastic hinge.
The spring button should line up with the access hole in the plastic sleeve on
the hinge. The spring button will rebound and lock the tube in place.
Repeat to complete the assembly of the other three corner hinges.
Pull straps to tighten Latch Closed
Latch Open Swung Down
SPRING BUTTON SPRING
BUTTON

English8
Installing Your Bed Rail
NOTE: The following steps may require the help of an additional person.
NOTE: In order to adjust the bed rail to fit your specific bed properly, you
may need to release the strap locking buckles located on the under side of
the plastic hinges. The anchoring straps should not be twisted. If twisted, the
anchoring straps may not tighten properly.
STEP 1
Remove the mattress from the bed you will be mounting the double sided bed
rail to. Place the assembly atop the box spring or mattress support structure so
that it is positioned in the orientation of its final placement.

English 9
STEP 2
Once the bed rail is placed properly, place the
mattress back atop of the box spring or mattress
support, sandwiching the flat metal bars on the corner
hinges and the anchoring straps between the box
spring and the mattress.
NOTE: In order for the bed rail mesh wall to be firmly held against the side
of the mattress you MUST properly tighten the anchoring straps. Please
follow STEPS 3 – 4 carefully.
STEP 3
Tighten the straps to bring the bed rail into its proper position. To tighten the
straps, first release the strap locks on the under side of the plastic hinges.
Pull the straps towards you until all the excess slack has been pulled out from
under the mattress and both sides of the bed rail are firmly pressed against the
sides of the mattress.

UNLOCKED
LOCKED
UNLOCKED
LOCKED
English10
NOTE: When using this bed rail on a foam mattress with little or no internal
structure, make sure not to over tighten the mounting straps. If over-tightened,
the mattress will likely fold or buckle in the middle and this will cause the
bed rail to not provide your child with the highest level of safety. Make slight
adjustments to find the best level of tightness on your mattress.
STEP 4
If the strap does not pull through smoothly, the strap may be twisted under the
mattress. Correct this before continuing with the installation. Once you have
taken the slack out of the straps, give one final pull on the strap end, hold it,
and push down on the locking buckle to secure the strap tension. Use the
same procedure for each side to properly secure the bed rail.
LOCKING
BUCKLE

English 11
NOTE: After locking both buckles, check to make sure that the mesh wall of
the bed rail is firmly up against the side of the mattress. There should be NO
GAPS. If the mesh wall is not firmly against the side of the mattress, check to
make sure the locking buckle is functioning properly and that the strap is not
twisted beneath the mattress. Once this has been checked and corrected if
needed, unlock the buckle, pull on the end of the strap to tighten and lock the
buckle again.
Store the excess anchoring strap material by tucking it under the mattress.
STEP 5
With your bed rail in the 'up' position push down on the locking tabs to secure
your bed rail in place.
LOCKING TAB

English12
NOTE: Be sure to continue to hold the upper part of the bed rail so that it does
not drop down on its own.
Operating the Swing Down Feature
STEP 1
With the bed rail side in the ‘up’ position, release the locking tabs on each
swing lock and arm assembly by pushing them up. This will allow the upper
part of the bed rail to move freely.

English 13
STEP 2
With both locking tabs turned to the ‘open’ position, hold the upper part
of the bed rail firmly and swing it down. The bed rail should now be in the
‘down’ position.
To return the bed rail to the ‘up’ position, reverse STEPS 1 – 2.
NOTE: Make sure that the bed rail is in the ‘up’ position and the locking tabs
are securely closed before leaving a child alone in the bed.

English14
CARE AND MAINTENANCE
Periodically check the bed rail for signs of damage, wear or for missing
components. Do not use if any part is missing, worn or damaged. Check the bed
rail regularly to make sure all hardware and mountings are tight and secure. Do not
use abrasive cleaners or bleach when cleaning. Proper cleaning of bed rail can be
done by sponging it with warm water and mild detergent.
90 DAYS LIMITED WARRANTY
If, during the first 90 days after consumer purchase of the item, under reasonable
and non-commercial use and conditions of maintenance, it fails while owned by
the original purchaser because of the quality of materials or workmanship of finish
and assembly, Regalo International, LLC, will replace or repair it at Regalo’s option.
PROOF OF PURCHASE REQUIRED.

English 15
Replacement Parts
A
BF
C
D
E
G
D
E
C
B
A SD – Mesh Wall
White = #23069
B SD – Right Upper Support Bar
Platinum = #24070
C SD – Left Upper Support Bar
Platinum = #24071
D SD – Right Bottom Support Bar
Platinum = #24074
E SD – Left Bottom Support Bar
Platinum = #24073
F Right Double Swing Lock Assembly
White = #23082
G Left Double Swing Lock Assembly
White = #23081

French16
www.regalo-baby.com
Regalo International, LLC.
3200 Corporate Center Drive, Suite 100 / Burnsville, MN 55306, É.-U.
866.272.5274 (aux États-Unis seulement) ou 952.435.1080
Fabriqué en Chine
Barrière de lit
rabattable double
GUIDE D'UTILISATION MODÈLE : 2250, 2250CA
• LIRE TOUTES LES INSTRUCTIONS AVANT D'ASSEMBLER ET
D'UTILISER LA BARRIÈRE DE LIT.
• CONSERVER CES INSTRUCTIONS POUR UNE UTILISATION
ULTÉRIEURE.

French 17
Avant d'utiliser le produit
Lire et suivre attentivement les instructions pour assurer une installation conforme
du produit. Négliger les instructions de ce guide de montage et d'utilisation de
la barrière de lit pourrait entraîner de graves blessures ou la mort. Vous êtes
responsable de la sécurité de votre enfant. Conserver ces instructions pour
consultation.
MISE EN GARDE
• DANGER DE SUFFOCATION ET D'ÉTRANGLEMENT
• De jeunes enfants se sont coincés dans l'écart à l'intérieur et
autour des barrières du lit, et des nourrissons en sont morts.
• NE JAMAIS utiliser avec des enfants de moins 2 ans.
UTILISER UNIQUEMENT avec des enfants capables de se
coucher dans un lit pour adulte et d'en sortir seuls, sans
aide. NE JAMAIS utiliser à la place d'un lit de bébé.
• NE JAMAIS utiliser si la barrière de lit n'est pas appuyée
fermement contre le matelas, sans aucun écart, et éloignée
d'au moins 23 cm (9 po) de la tête et du pied de lit. Ne
pas combler l'écart avec des oreillers, des couvertures ou
d'autres articles risquant d'étouffer l'enfant.
• NE JAMAIS utiliser sur un lit pour tout-petit, un lit superposé,
un lit d'eau ou un lit avec un matelas gonflable. Utiliser
UNIQUEMENT sur un lit pour adulte.
• Utiliser UNIQUEMENT sur un lit de dimension lit à une place
à grand lit.
•Utiliser UNIQUEMENT sur un lit d'adulte avec sommier et
matelas.
• L'utilisation de cette barrière de lit est DÉCONSEILLÉE sur
un lit à plate-forme ou de style similaire.
• L'utilisation de cette barrière de lit est réservée à des enfants
de 2 à 5 ans.
• Cesser l’utilisation si la barrière de lit d'enfant est
endommagée, cassée ou s’il manque des pièces.
•Ne pas utiliser si la barrière de lit n'est pas complètement
assemblée.
•Vérifier périodiquement que toutes les broches de ressort
sont complètement engagées sur les barres de support de
barrière de lit.

French18
VEUILLEZ VÉRIFIER QUE VOUS DISPOSEZ DES ARTICLES SUIVANTS:
A Housse en tissu (2)
B Barre de support supérieure de droite (2)
C Barre de support supérieure de gauche (2)
D Barre de support inférieure de droite (2)
E Barre de support inférieure de gauche (2)
F Ensemble de verrou basculant droit et sangle (1)
G Ensemble de verrou basculant gauche et sangle (1)
Avant l'assemblage
A
BF
C
D
E
G
D
E
C
B

French 19
Assemblage de la barrière de lit
REMARQUE : Assurez-vous que les chevilles à ressort sont bien insérées
dans les trous opposés de la barrière de lit pour verrouiller les deux pièces.
ÉTAPE1
Insérez la barre de support supérieure de gauche dans la barre de support
inférieure de gauche. Assurez-vous que la cheville à ressort est bien insérée
dans le trou opposé pour verrouiller les deux pièces. Répétez sur le côté
droit de la barrière de lit.
Insérée
ÉTAPE2
Enclenchez les sections gauche et droite de la barrière de lit que vous venez de
former pour les joindre.
BOUTON
À RESSORT
BROCHE
DE RESSORT

French20
REMARQUE : Si la fermeture éclair bloque, faites les ajustements nécessaires
pour fermer la housse correctement sur le cadre. N’UTILISEZ PAS la barrière de
lit si la fermeture éclair de la housse en tissu n’est pas correctement fermée.
ÉTAPE3
Pour installer la housse de tissu
sur labarrière de lit, glissez-la
jusqu’à l’autre extrémité du cadre
et fermez la fermeture éclair pour
compléter la procédure.
Répétez les ÉTAPES 1 à 3 pour
assembler le deuxième côté de la
barrière de lit.
Pull straps to tighten Latch Closed
Latch Open Swung Down