Regency City Series New York 40 User manual

Regency City Series New York 40
CV40E-NG11 / CV40E-LP11
FRAMING
DIMENSIONS
SPECIFICATIONS
HEAT RELEASE REQUIREMENTS
QR LINK FOR
PDF DIGITAL COPY
OF SPECIFICATIONS:
MUST READ BEFORE
FRAMING
IMPORTANT INFORMATION

6| CV40E-11 City Series
dimensions
33 7
16 "
849mm
43"
1091mm
25 9
16"
648mm
46 1
4“
1175mm
71
4"
183mm
40
1016mm
Ø 6 3
4"
171mm
Ø4"
102mm
11 7
16 "
291mm
21 7
8"
556mm
18 11
16 "
475mm
17 11
16 "
449mm
15 1
16 "
382mm
77
8"
200mm
37 3
8"
949mm
34 5
8"
879mm
10 1
2"
267mm
"
"
2'' (51mm)
13''
(330mm)
3-1/2''
(89mm)
Note: Electrical connection on left hand side of the appliance.
A metal receptacle box is supplied/installed with the appliance to make all 120 volt electrical connections.
CV40E Dimensions
Note: Height Dimension may vary depending on the height of the leveling legs.
Dimensions will appear as (inches)" / (metric)mm
throughout this manual. The inches are rounded to the
nearest 1/16" when converted, when greater accuracy
is required, use the metric dimensions.
Note: These units are non-load bearing.
ALL PICTURES / DIAGRAMS SHOWN THROUGHOUT THIS MANUAL ARE FOR ILLUSTRATION PURPOSES ONLY.
ACTUAL PRODUCT MAY VARY DUE TO PRODUCT ENHANCEMENTS.
Gas Line Entry

CV40E-11 City Series | 25
requirements
installer's information
Ventilation Openings
Regency's patented Cool Wall system releases warmth at ceiling level. This
system reduces excessive radiant heat in front of the replace so you can
enjoy your replace more often.
• Design your own chase vent solution to suit your home
• Use optional front or left & right side chase vent grills
• Release warmth into the room discreetly
Front Exit
The ventilation opening may be placed in front ensuring it meets the 120
square inch opening & is located 0-3" (76mm) from the enclosure ceiling.
SIde Exit (Left/Right)
Ventilation openings, when placed on both sides, must be of the same size.
They must be have an equal split (50/50) free air opening to balance air ow.
A ventilation opening may never be on one side only.
The ventilation openings cannot be any smaller than 6" (152mm) wide to
equal the total area of 120 square inches of free open area.
Example: 6" (152mm) wide x 10" (254 mm) High = 60 square inches per
side of free open area. A second ventilation grill is installed on the other side
to =100%.
The ventilation openings must be located 0-3" from the enclosure ceiling.
Top Exit
The ventilation opening may be short of the ceiling as shown below.
Minimum opening height must be 1-1/2" (38 mm) measured from top of
enclosure to the ceiling and must be in open in front and both sides to
meet the minimum 120 square inches free open air requirement.
Ventilation Opening Locations
The following are examples of how the ventilation openings may be placed
above the replace.
If using the optional heat wave kit, this does not reduce the size of the
ventilation opening. The ventilation opening(s) must be a minimum 120
square inches regardless.
The air travelling through the heat exchanger is heated by the replace and
then directed out the back of the replace. The combined warmed air is then
vented back into the room.
The ventilation opening may be fully open at the top of the enclosure.
This type of ventilation opening would be used when the top of the
enclosure is not visible from above and where the ceiling within the
room is higher than normal. When creating this type of ventilation
opening, measures should be into place to avoid having objects of any
type falling or be thrown into the ventilation opening. Mesh screen or
other preventative measures should be put into place.
The ventilation opening may be placed on top ensuring it meets the 120
square inch opening. This type of ventilation opening would be used
when the top of the enclosure is visible from above and where the
ceiling within the room is higher than normal.

26 | CV40E-11 City Series
installer's information
Chase Enclosure
Max 3”
(76 mm)
Ceiling Ceiling
Top of chase enclosure
Max 3”
(76 mm)
Stud
Stud
Stud
Stud
40” (1016 mm) Chase Vent
C40 Chase Vent Framing Clearances
Opening for vent
4”-4.5”
(102 mm x 114 mm)
Min 42.25” (1073 mm)
Framed opening must be between 4” (102 mm) and 4.5” (114 mm) tall, and at least 42.25”(1073 mm) wide
to accommodate the chase vent. The top of the chase vent opening must be 3” or less from the top of the
chase enclosure.
40” (1016 mm) Chase Vent
Top of chase enclosure
In the example above, the ceiling does not
meet the requirement as it is higher than
the specied minimum.
Top of chase enclosure is sealed o to
meet the 0-3 (76 mm) requirement.
Top of chase enclosure
Minimum 120sq. inch opening
Minimum 120sq. inch opening
When choosing to install the ventilation openings from the front or both sides, The top of the ventilation opening cannot be any lower than 0-3" from the top
of the chase enclosure for all installations.
Minimum height of enclosure from base of appliance is 63".
A minimum 120in2 opening in the enclosure is required to maintain safe operating temperatures. This can be achieved in a number of ways including the
examples shown in this manual.
IMPORTANT:
Exterior wall/Alcove enclosure: When installing into an exterior cavity or alcove enclosure (ceiling, back and sides), regardless of where appliance is
placed within the home, requires the use of either drywall or other means such as plywood, wood studs, etc. to prevent heat from escaping anywhere above
/through the enclosure other than the required grill / ventilation opening.
Internal chase: When installing as an internal chase framing installation ,regardless of where appliance is placed within the home, requires the use of either
drywall or other means such as plywood, on the rear wall of the chase to eliminate heat escaping into the rear wall cavity. If the chase is extended to the
ceiling ,the ceiling will also need to be nished in a manner to prevent heat escaping into oor joist/attic space.
One of the following methods must be used to prevent the heat from escaping.
a. If choosing drywall, ensure that the drywall is butt up tight with no gaps.
b. Plywood, wood studs, etc. installed tightly with no gaps.
As this appliance has been designed with all hot air escaping through the chase enclosure ventilation/grill openings only, if hot air is trapped as a result of
the hot air escaping through joints, crevasses, open studs, or other openings within the enclosure above, this will change the clearances within the enclosure
causing the enclosure to overheat. It is vital that all the hot air from within the enclosure exits through the ventilation openings only.
Ensure that the ventilation openings are made as such to prevent debris, objects from falling into the enclosure.
Warning: DO NOT cover or place objects in front of the ventilation opening air outlet(s).

CV40E-11 City Series | 27
installation
Clearances
The clearances listed below are minimum distances unless otherwise stated.
A major cause of chimney related res is failure to maintain required clearances (air space) to combustible materials. It is of the greatest importance that
this replace and vent system be installed only in accordance with these instructions.
Caution Requirements
The top, back and sides of the replace are dened by
standos. The metal ends of the stando may NOT be
recessed into combustible construction.
WARNING
Fire hazard is an extreme risk
if these clearances (air space) to combustible materials are
not adhered to. It is of greatest importance that this replace
and vent system be installed only in accordance with these
instructions.
Clearance: Single Sided Dimension Measured From:
A: From Floor Min. 0" Bottom of Fireplace Opening
A1 : Mantel Height (min.) ** Top of Fireplace Opening
B: Sidewall (on one side) 8-1/2" (216mm) Side of Fireplace Opening
C: Enclosure Width (min.) 46-3/4" (1187mm) Minimum inside dimensions
D: Mantel Depth (max.) **
E: Alcove Width 84" (2134mm) Side wall to side wall (min.)
F: Alcove Depth 36" (914mm) Front of Unit
G: To Enclosure Ceiling (min/max) 0-3" (0-76mm) From top of enclosure
H: Convection Air outlet 120 sq. inches (min) * Top/front or side of enclosure
I: Enclosure Depth (min.) 19" (483mm) Minimum inside dimensions
J: Opening Height 15-1/16" (383mm) Bottom/Top of Fireplace Opening
K: To Ceiling (min) All 3 sides 1-1/2" (38mm) To Top of Ceiling
L: Chase Enclosure (min.) 63" (1600mm) From base of unit/oor
M: Clearance to sprinkler head (Min.) 36" (914mm) Perpendicular from chase grill
Hearth 0" No hearth required
** See mantel clearances chart in this manual
Flue Clearances to Combustibles
Horizontal - Top 3" (76mm)
Horizontal - Side 2" (51mm)
Horizontal - Bottom 2" (51mm)
Vertical 2" (51mm)
Passing through wall/
floor/ceiling - when
restop is used.
1-1/2" (38mm)
* A minimum of 120 square inches of open area, not lower than 3" (76 mm) from top of
enclosure, required for all installations — this can be achieved by having an open area in
front, both sides, and/or above as shown in the four diagrams on the next page.
The HeatWave Duct Kit has
dierent clearance and framing re-
quirements, check the HeatWave
manual for details.
E
F
Alcove
Side View
L
Chase grill
Sprinkler
M

28 | CV40E-11 City Series
installation
Clearances
Floor to ceiling with top ventilation opening Low framing with ventilation opening in front/2 sides or top
Full framing with low ventilation opening in front or 2 sides Full framing with ventilation opening in front or 2 sides
Note: The ventilation opening may only be placed above, on both sides and in front as shown above.
Ventilation grills can never be placed behind the appliance.
K
C
I
A1
A
D
L
J
H
B
L
I
C
D
A1
A
J
G
G
H
H
H
B
H
I
C
G
A
A1
G
D
J
L
H
H
B
H
I
A1
A
D
C
J
G
G
L
H
H
B
H

CV40E-11 City Series | 29
installation
Optional Flush Front Chase Vent Installation - Part #657-991 (White)
Max 3”
(76 mm)
Ceiling Ceiling
Top of chase enclosure
Max 3”
(76 mm)
Stud
Stud
Stud
Stud
40” (1016 mm) Chase Vent
C40 Chase Vent Framing Clearances
Opening for vent
4”-4.5”
(102 mm x 114 mm)
Min 42.25” (1073 mm)
Framed opening must be between 4” (102 mm) and 4.5” (114 mm) tall, and at least 42.25”(1073 mm) wide
to accommodate the chase vent. The top of the chase vent opening must be 3” or less from the top of the
chase enclosure.
40” (1016 mm) Chase Vent
Drywall
Header Stud
C40 Chase Vent Finish Detail
Finish edges of drywall
with trim or corner bead.
Edge finish must not decrease
opening area below 130in (3.25" x
40") or (83 mm x 1016 mm)
Finish edges of drywall
with trim or corner
bead. Edge nish
must not decrease
opening area below
130in (3.25'' x 40'')
or (83mm x 106mm)
This optional ush front chase vent grill is designed so that only the grills are exposed. The 4 anges in front which secure the chase vent grill to the stud
work is covered by the drywall to give a seamless look.

30 | CV40E-11 City Series
installation
C40 Chase Vent Installation Example
1. 2. 3.
4. 5. 6.
Frame opening for vent
(See Vent Framing Clearances Page)
Screw Chase vent to Framing Use at least 3 sets of screws
to keep the vent at against framing
Frame wall with nishing material If necessary, mark where the
chase vent is located before
fixing drywall in place
Cut hole in nishing material
around inside of chase vent.
Finish edges around opening
Drywall

CV40E-11 City Series | 31
installation
Optional Front Grill Installation - Part #656-991 (Black)
A
B
C
B
A
C
Optional Side Grill Installation - Part # 656-992 (Set of 2/Black)
Unit may not be exactly as shown,
but the drawing dipicts the process.
A
C
B
DIMENSIONS
A 39-1/8'' (994mm)
B4-3/8'' (111mm)
CMaximum 3'' (76mm) from top of enclo-
sure.
Secure with screws from the front through the sides.
DIMENSIONS
A Maximum 3'' (76mm) from top of enclo-
sure.
B8-5/16'' (211mm)
C8-5/16'' (211mm)
Secure with screws through louvers to the sides.
This optional grill meets the requirement of the 120 square inches required for the enclosure in all installations and is designed to keep the enclosure cool.
In this application, both the ange and screws to secure the grills are exposed as this grill is designed to be installed after the nished facing has been placed
on the wall.
To install the front grill - frame an opening of 4-3/8'' H x 39-1/8'' W (111mmm H x 994mm W).
The nished facing material should be attached and be the same size as the framed opening to eliminate gaps.
Install the grill and secure in place with one screw on either side, installed from the front.
These optional grills meet the requirement of the 120 square inches required for the enclosure in all installations and are designed to keep the enclosure cool.
In this application, both the ange and screws to secure the grills are exposed as this grill is designed to be installed after the nished facing has been placed
on the wall.
To install the side grills - frame an opening of 8-5/16'' H x 8-5/16'' W (211mm H x 211mm W).
The nished facing material should be attached and be the same size as the framed opening to eliminate gaps.
Install the grill and secure in place with one screw on either side, installed from the front through the louvers.
Repeat steps to install the second grill to the other side of the chase.

32 | CV40E-11 City Series
installation
Mantel Clearances
Combustible mantel clearances from top of front facing
are shown in the diagram on the right.
Mantel Leg Clearances
Combustible mantel leg clearances as per diagram:
212 6 4810
0
14
9" (229 m)
15-1/16”
(383 mm)
10
20
26
Top of
Fireplace
Opening
12" (305 mm)
1/2" (13 mm) Drywall, wood,
wood panel, etc.
5-1/8"
(130 mm)
To
Bottomof
Fireplace
Opening
12"
4"
Allowable mantel
MANTEL LEG
leg projection
7"
8-1/2"
2"
CV40E