Regulus CSE TV ZV G 1F User manual

www.regulus.eu
CSE TV ZV G 1F
CSE TV ZV G 1F
EN
Installation and Operation Manual
CSE TV ZV G 1F PUMP STATION

1. Introduction
This pump station is intended to ensure circulation in DHW distribution piping in buildings, or to
ensure hot water recirculation in DHW heating systems.
2. Description of the pump station
It consists of a UPM3 DHW 15-70 pump incl. power cable, insulation, check valve, two ball valves
and thermometer.
Main features
Application DHW circuits – recirculation or heating in a heat exchanger
Description consists of UPM3 DHW 15-70 pump, insulation, valve, two ball
valves and thermometer
Working fluid water, drinking water
Installation to the piping, min. distance of the pipe axis from a wall is 100 mm
Code 15181
Data of CSE TV ZV G 1F Pump Station
Fluid working temperature 2 - 95 °C
Max. working pressure 10 bar
Min. working pressure 0.5 bar
Ambient temperature 5 - 40 °C
Max. rel. humidity 80 %, non condensing
Power supply 230 V, 50 Hz
Insulation material EPP RG 60 g/l
Overall dimensions 325 x 140 x 150 mm
Total weight 2.0 kg
Connections 2x G 1" F

3. Direction of Flow through the Pump Station
SMĚR PROUDĚNÍ
4. UPM3 DHW 15-70 Pump, 130 mm
Design
A wet-running circulation pump, G 1“ M connection.
Electrical data
Power supply 230 V, 50 Hz
Power input (min./max.) 2/52 W
Current (min./max.) 0.04/0.52 A
IP rating IP44
Max. speed 5766 rpm
Weighted average power ≤ 23 W
Energy Efficiency Index ≤ 0.20 by EN 16 297/3
Motor protection not needed
FLOW DIRECTION

Pump control
The circulation pump can be controlled without a PWM signal by selecting the pump performance curve
or using an external PWM control signal (prole for use in heating systems). A PWM pump control cab-
le with connector is not included. It can be purchased as an optional accessory (code 16792), cable
length 2 m.
The maximum operating curve of the pump can be dened.
- with no PWM signal the pump runs at max. speed following the selected curve
- with PWM signal the pump speed changes with the signal value up to the maximum of the
selected curve
Performance curves
Curve Max. H
(upper
graph)
Max. P1
(lower
graph)
1 5 mH2O 33 W
2 6 mH2O 39 W
3 7 mH2O 52 W
H [mH2O]

Performance display
DISPLAY - LED MARKING
DISPLAY PERFORMANCE
CURVE
STATE Max. H (upper
graph)
1LOW PERFORMANCE 5 m
2MEDIUM PERFORMANCE 6 m
3HIGH PERFORMANCE 7,0 m
WARNING: LEDs may be mirrored, depending on the specic pump type.
GREEN LED FLASHING FREQUENCY GREEN LED FLASHING FREQUENCY
1 flash per second NO
12 flashes per second YES
When switched on, the pump runs at factory settings or the last setting. The display shows the current
pump performance.
Setting Selection for UPM3
To select your desired setting, press the button repeatedly until you nd the setting you need (see the
gure above). If you pass the desired setting, you have to go one more round until it appears again.
Error Display
DISPLAY CONTROL MODE
Seized pump
Too low power supply voltage
Electric fault
Prohibited positions
The LED numbering is further omitted for better clarity.

Permissible positions
Pump Wiring
socket for power supply (A)
and signal transmission (B)
power supply (A)
and signal (B) connectors
N (blue)
L (brown)
PE (yellow-green)
PWM GDN (blue)
iPWM out (black)
PWM in (brown)
connector (B) with 2m cable is not
included in supply; it can be purchased as
optional accessory, code 16792

©2022 We reserve the right to errors, changes and improvements without prior notice.
REGULUS spol. s r.o.
E-mail: [email protected]
Web: www.regulus.eu
v1.2-05/2022