REID LIFTING PORTAGANTRY 11000 Installation instructions

US.REIDLIFTING.COM Assembly & Operation Guide
PORTAGANTRY11000

Correct Operation 4
Intended Use
Maximum Capacity
Inspection Prior to Initial Operation
Inspection Before Starting Work
Temperature Range
Notes for Correct Operation
Warning
Traversing the Load
Moving Under Load
Fall Protection Applications 7
Use as a Fall Protection Anchor
Additional Notes for Correct Operation
Warning
IRATA
Inspection & Maintenance 9
Regular Inspections
Maintenance & Repair
Storage & Transportation
ATEX 10
ATEX
Classification [Zone 2]
Spark Formation
Static Electricity
Inspection, Maintenance & Repair
Assembly Instructions 12
Variants & Options 21
Dimensions 26
Quality & Safety 28
Regulations
Accreditations
Conformité Européenne [CE]
Testing
Language
Product IPR
Product Labelling 30
Inspection Record 31
Contents

3
PORTAGANTRY 11000
Lightweight.
Portable. Safe.
Please read the following instructions and
guidance notes carefully, before using or
operating the system.
They contain important information about how to
handle and use the system in a safe and efficient
way, avoiding danger, reducing repair costs
and downtime, and increasing the reliability and
lifespan of the system.
They apply for:
Operation, including preparation,
troubleshooting during operation and
cleaning
Maintenance, inspection and repair
Transportation
It is the responsibility of the end user to adhere
to the Health & Safety and accident prevention
standards and legislation valid in their respective
countries and any regions in which the system
is being used. A rescue plan also needs to be in
place in the event of an emergency that could
occur during the work. This document should
form part of the overriding Risk Assessment and
Method Statement required for each lift.

Intended Use
This product is designed, tested and intended to be
used for the lifting of goods, the lifting of personnel
or for providing a safety anchor for the prevention
of falls as part of a personal fall protection system.
(PFAS). The use of our products for these multiple
applications is consistent with the products
design, notwithstanding pre-user inspections and
mandatory inspections by a competent or qualified
person, determined by local regulations.
Maximum Capacity
Lifting of Goods: Each product will be marked with
a Capacity. The capacity is specifically intended as a
maximum limit for the lifting of goods, materials and
equipment and includes safety factors. When using
modular gantries, due to the interchangeability of
A-frames and beams to suit the customers need,
the lowest rated element of the gantry always takes
precedent. A-frames are independently marked
with a capacity for safety.
Lifting of Personnel: For the lifting of personnel
REID Lifting will reduce the capacity by half,
thereby increasing the safety factor of the product.
As for lifting goods, materials and equipment, the
lowest rated element of the gantry always takes
precedent. Associated equipment used for lifting
personnel must be rated accordingly. It is the
employers’ responsibility to ensure this is the case.
For example, a winch must be personnel rated and
where necessary, meet applicable standards and
regulations for the country of use.
Correct Operation
Fall Protection Anchor: In most cases (subject
to labelling and instructions for use for specific
products confirming this) REID lifting products
are tested and meet the requirements of fall
protection standards and regulations, including
ANSI Z359.18-2017 and various OSHA Regulations as
referenced in our Instructions for Use. The capacity
on the beam or A-frame is of no relevance to fall
protection standards and requirements and the
user should refer to the specific sections of the
instructions for use, for detailed information. For
example, ANSI requires that anchors that form part
of a personal fall protection system are capable
of withstanding a 5000lb static load (22.2kN) for
a single user, 7500lb (33.3kN) for two users and
10,000lb (44.4kN) for three users and so on. OSHA
requires a minimum safety factor of 2, validated
by a qualified person. REID Lifting products will,
where applicable be marked with the rating for
fall protection. Safety factors will be higher than
those for lifting and forces will be limited by the use
of personal fall protection equipment, including
load limiting devices such as shock absorbers or
self-retracting lifelines that reduce impact forces,
typically between 4kN and 8kN per user as
required by law.
Note: some jurisdictions may not allow the same
equipment to be used for lifting of materials and as
a component of a PFAS. Some employers may also
prefer to keep such equipment distinctly separate.
If this is the case, we would recommend that the
equipment is labelled accordingly.
Check your local regulations before putting
equipment to use and designate accordingly.
It is expected that all users of this product have
the necessary medical and physical capabilities,
are fully trained and deemed competent in its
safe assembly and use. We would remind users
of the requirement to ensure that work is properly
planned, risk assessments carried out and as
required, method statements for carrying out work
provided.
Where required the owner/user of the equipment
should ensure that a qualified person has been
consulted in respect of the need for structural
validation, for example (but not limited to);
calculating imposed loads for the safety of ground,
floor or roof structures during lifting operations.
This product has different ratings depending
upon the application as detailed in the table
below:
For fall protection applications see page 7.
Application Capacity
Goods Lifting [lb.] 11000
Personnel
Lifting [lb.] 5500

5
Inspection Prior to Initial Operation
Each product must be inspected prior to initial
operation by a competent person to ensure that the
structure is safe and that it has not been damaged
by incorrect assembly, transport or storage.
Inspection Before Starting Work
Before starting work, the product assembly and all
load-bearing components should be checked for
visual defects. This includes checking the integrity of
all profiles for denting, making sure there is no wear
or elongation on the bolt holes and ensuring that
the trolley moves freely along the beam.
Temperature Range
This product can be operated in ambient dry
temperatures between -10°F to 131°F (–23° to
+55°C). Consult your supplier in case of extreme
working conditions.
Notes for Correct Operation
We recommend the use of load-sensing or
overload protection devices on all lifts.
The risk assessment and method statement
must take into account any factors that might
apply additional loading to the product
during lifting operations.
Suitable, appropriately rated winches and
connection plates must be used for all
applications.
Take care when transporting and storing the
product to avoid damage.
Assemble only as instructed (ensure all
bolts are present and fitted correctly as per
instructions).
We recommend that appropriate PPE are
worn when using the equipment.
The product should be set up at a safe
distance from the hazard or lift area, before
moving the structure into place.
The beam must be horizontal prior to any lift
and A-frames vertical and parallel to each
other.
Do not use the product if the trolley does
not run freely along the beam. (for certain
applications, such as when the product is
being used as a restraint point, the trolleys can
be locked into position).
Attach the hoist to the lifting point on the
trolley only, making sure it is attached in a way
that does not expose the user to danger by
the hoist, chain or load.
Do not allow the load to swing.
When lifting keep the load low to the ground.
Only raise and lower loads when castor brakes
are engaged.
To ensure stability of the structure, the
operating span of the beam (C) must be equal
to or greater than the distance between the
castors on the A-Frame (G).
The supporting ground/structure where
the gantry is to be used must be stable
and capable of withstanding the maximum
expected load applied during use.
To avoid side pull, lowering and lifting should
only be carried out when the load chain forms
a straight and vertical line between the load
and lifting attachment point on the trolley
(refer to figure A).
PORTAGANTRY 11000
A

Warning
The equipment should not be used outside
of its limitations, or for any purpose other than
that for which it is intended.
When winching, only use one winch with each
sheave and make sure they never cross paths
with each other.
Do not lift or transport loads while personnel
are in the danger zone.
Do not allow personnel to pass under a
suspended load.
Never leave a suspended load unattended.
It is not recommended to mix the use of
the gantry with personnel and goods lifting
simultaneously.
Do not start moving the load along the beam
until you have checked that it has been
attached correctly.
When moving a loaded trolley along
the beam, move the load steadily and in
a controlled manner and avoid sudden
movements.
Don’t allow the load to hit the product frame.
Be aware of hazards when setting up/folding
down, such as trapping fingers in rotating
parts.
Be aware of any adverse weather conditions
such as strong or gusty winds which could
impose additional horizontal loads and affect
the stability of the structure. Stop using if
weather is impacting on lifting, and either
disassemble the gantry or tie it to a rigid
structure to ensure it can’t overturn.
Traversing the Load
This product is designed so that the load can be
traversed along the beam using the trolley. At larger
capacities and/or longer beams this action can
become difficult. REID recommends that either a
geared trolley or a rope control product be used
to reduce the effort and provide more control over
the movement.
The rope control product allows the operator to
control the movement of the trolley from a safe
location at the side of the grantry. The product
includes a winch and series of pulleys that introduce
a mechanical advantage and reduce the effort
during operation.
For further information please contact your REID
representative.
Moving Under Load
When moving the gantry underload, the following
instructions MUST be followed:
This product can only be moved in the direction
perpendicular to the beam.
Directional locks must be used on the castors
(perpendicular to the beam only).
The end user MUST make sure the center of
gravity of the load is known and the lifting points
are in such a way that the load is EQUALLY
distributed, so the load generates a vertical pull
to the beam.
The load is not allowed to swing.
The floor must be smooth, flat, free from cracks
or steps and the weather conditions should be
safe for the operation (i.e. not when frost, ice or
snow present).
A risk assessment and method statement are
required to be completed by a competent
person before moving the gantry under load.
This products movement must be controlled at a
slow speed, no sudden movements or high speeds
are allowed.
Correct Operation

7
Application
Capacity
11000
Fall Arrest* 3 persons
*Only applicable to this product being used in accordance with
ANSI Z359.18. The system can support more users in Fall arrest if
used in accordance with OSHA 1910 Subpart I or 1926 Subpart M.
Please contact REID Lifting for further details.
Use as a Fall Protection Anchor
This section must not be read in isolation from
all other sections of this manual. Read the whole
manual before using this product.
Fall arrest: This product is tested and conforms to
the requirements of ANSI Z359.18-2017 type D for
fall arrest protection for single or multiple users
depending on the configuration of the product.
The Product can be used as part of a personal fall
protection system that meets the requirements of
ANSI Z359.18, OSHA 1910 subpart I and 1926.502
subpart M. When being used for fall arrest, the
operator must use a body harness and a shock
absorber that complies with the relevant national
standards and regulations and that limits the
maximum allowed force (MAF) to 8kN.
Users may be attached to the system via a
traveling trolley (which may also be locked in
place) or via a fall protection device mounted
to the side cheek plate of the A frame, which
is subsequently deviated through a pulley and
sheave carrier. Only one person should be
attached to each trolley in accordance with the
notified capacity. Each personnel lift must be
properly planned, and all weights clearly known
along with a clear understanding of the capacity
and constraints of all personal fall arrest system
components.
The capabilities stated in the table below apply to
standard range systems only. If unsure about your
system consult serial labels, information filled in on
page 31 or consult your supplier. Custom versions
of the system are available tailored to specific
lifting needs. These versions are designated with
a ‘C’ at the end the product number on the serial
label attached to each A-frame and beam.
This product has different ratings depending
on the application, the ratings for fall protection
applications are detailed in the table below:
Additional Notes for Correct
Operation
The anchorage must always be above the users
head to prevent dangerous free falls.
Always carry out pre-use checks before using
this equipment. It is advised to use a buddy
system and inspection must be by a competent
person.
The fall arrest device must only be attached to
the lifting point on the trolley or the designated
location on the cheek plate or upright. (see
product images and set up instructions).
Never walk away from the footprint of the
product or move outside designated safe
zones whilst connected to it where there is a
risk of a fall (refer to figure B). Ensure that the
operating area is within the footprint of the
system before beginning work.
When using the product as a fall arrest anchor
ensure there is adequate fall clearance
when working at height (refer to figure C). A
competent person should calculate this taking
into account all of the components of the
personal fall arrest system and allowing a safety
margin.
PORTAGANTRY 11000
Fall Protection Applications
C
B

Inspection & Maintenance
Only use the product for fall arrest applications
when the castor brakes are engaged.
To ensure stability of the structure, the
operating span of the beam must be equal
to or greater than the distance between the
castors on the A-frames.
Always consider the potential effects of
sharp edges, chemical reagents, electrical
conductivity, cutting, abrasion, climatic
exposure on all components of the fall
protection system, and the effect of offset
forces as a result of pendulum falls.
Ensure the structure on which the product is
mounted is horizontal. If necessary, adjust the
products feet to achieve a level operating
structure.
If the product has been subjected to a fall
arrest or impact force it must be immediately
removed from service.
The substrate of the structure on which the
product is placed must be able to sustain the
loads specified for the device in all orientations
permitted, including a safety factor of at least 2.
Never exceed the number of allowable users.
Never adjust the product whilst a person is
attached to it.
Only use designated anchor points for the
attachment of fall protection devices.
Ensure that any fall protection system
components being used are compatible and
meet the requirements of applicable standards.
When using this equipment ensure that there is
a rescue plan prior to starting work and ensure
that users are trained in the correct execution
of the plan and have all necessary rescue
equipment to hand.
Where required by regulation, each installation
must be approved by a qualified person.
Always wear appropriate PPE when installing,
setting up, dismantling and using this
equipment.
Misuse of this product could result in serious
injury or death.
Warning
For fall protection applications the maximum
user weight is 330lb (150kg) or the weight
allowed by the lowest rated piece of
equipment in the fall arrest system.
Ensure that you have read and understood the
maximum force tables for each anchor point.
This equipment must only be assembled,
installed and used by persons who have been
trained in its correct application and use.
When using for fall protection, only use one
fall arrest device with each pulley/sheave and
make sure that working procedures prevent
individual lifelines from crossing and becoming
tangled.
When using the product in conjunction with
another manufacturers fall protection products,
ensure that you have read the instructions for
use of those products to ensure their suitability
and any restrictions for use. Only use approved
brackets for the connection of winches and
self-retracting lifelines.
It is essential for safety that the product is
withdrawn from use immediately and not be
used again until confirmed in writing by a
competent person should
1. Any doubt arises about its condition for
safe use or;
2. It has been used to arrest a fall
3.It has been used for any other purpose,
other than as a component of a personal
fall protection system
IRATA [International Rope Access
Trade Association]
This product is suitable for rope access and has
been tested to 15kN (3300lb) static load as per
test requirements of IRATA international code of
practice (ICOP).

9
ATEX
The following information is based on REID
Lifting’s recommendations and does not remove
the responsibility of the user to comply with the
relevant regulations and standards that are valid
in the respective countries and regions where the
system is being used.
Regular Inspections
To ensure that the product’s frame remains in safe
working order it must be inspected regularly by a
competent or qualified person. We recommend
inspections every 6 months for personnel lifting
and every 12 months for goods only, unless
local regulations, adverse working conditions or
profile of use and risk dictate shorter periods. The
components of the system need to be checked
for damage, wear, corrosion or other irregularities.
It may be necessary to disassemble the system
in order to do this. Particular attention should be
paid to checking the profiles for denting, pins and
fixings for integrity, making sure there is no wear
or elongation on the bolt holes and ensuring that
the trolley moves freely along the beam.
It is recommended that once inspected or
repaired, the device is marked with the date of
the next inspection.
Inspections are instigated by the user. If detailed
information is required on inspection and test
criteria, please contact your supplier’s technical
department or REID Lifting.
The equipment Inspection Record is on page 31.
If using the product in explosive atmospheres, see
additional section titled ATEX.
Maintenance & Repair
In order to ensure correct operation, the
conditions for inspection and maintenance must
be complied with. If any defects are found, stop
using the product immediately.
No alterations or additions to the equipment
beyond the replacement of standard parts by
an authorized representative should be made
without the written consent of the manufacturer.
Any necessary repairs identified during
inspections should only be carried out by an
approved specialist workshop using original
spare parts. Any repair must be carried out in
accordance with the manufacturer’s instructions.
It is recommended to maintain the equipment in
a clean and dry manner. Cleaning is suggested
using a sponge or cloth with warm, soapy water,
rinsing and allowing to dry.
This product must be assembled using metric
fixings of the same type and quality as those
supplied by the original manufacturer only.
Failure to do so could have an impact on the
structural performance and stability of the
product. REID Lifting and its resellers can supply
these spare parts locally.
Storage & Transportation
When transporting the components, take note of
all the manual handling considerations.
Do not throw the product down or stack any
items on top of it.
Always place carefully and security on the
ground to avoid damaging the equipment.
PORTAGANTRY 11000

ATEX
ATEX
This product has been designed for use in
explosive atmospheres in line with the following
requirements and information. Any use which
differs or exceeds this is considered incorrect
and REID Lifting Ltd will not accept any
responsibility or liability for damages resulting
from false application. The risk is solely with the
user. If the product has been customized in
any way, then it may not comply with standards
and no longer be suitable for use in explosive
atmospheres. If this is the case, then the product
will not have any of the markings below. If in
doubt, please contact your REID representative.
Classification [Zone 2]
As standard, the product meets the requirements
of Category 3 equipment for use in Zone 2
explosive atmospheres, providing a normal level
of protection where mixtures of air and gases,
vapors or mists or by air and dusts mixtures are
unlikely to occur or, if they do occur, are likely
to do so only infrequently and for a short period
only.
The product will have the following identification
on the serial label:
As Standard for Zone 2 Environments:
II 3 GD T6
Identification for protection against explosions
II: Unit group II – non-mining application
3: Category 3 – Normal safety for use in Zone 2
GD: For use in gas (G) & dust (D) atmospheres
T6: Temperature class – Max 85°
Spark Formation
There is an Increased danger of ignition when
certain material pairings clash, namely non-
corrosion-resistant steel or cast iron against
aluminum, magnesium or pertinent alloys. This
applies especially in the case of rust or surface
rust. When assembling the product and inserting
fastening components, these must therefore be
clear of rust and debris of any kind. As stated
previously, care must be taken to ensure the
gantry is handled in a suitable manner, never
thrown down and always placed carefully onto
the ground.
For Zone 2 applications, the height of the
product should not be adjusted using the
ratchet mechanism and/or geared wheel
within those zones.
REID recommends the use of corrosion
resistant tools when assembling the product
to prevent the possibility of any sparks.

11
Static Electricity
For Zone 2 applications, there is a potential
risk of static electricity build-up leading to
an incentive spark. Although the risk of such
ignition is unlikely, the product must be earthed
during assembly and use. This can be achieved
by attaching an earthing lead to a convenient
location on metallic parts of both the product
and trolley.
If using the product in explosive atmospheres,
in addition to the Regular Inspection and
Maintenance information above, these additional
instructions should be followed:
Inspections must be instigated by the user prior
to each use if used in a potentially explosive
atmosphere.
Inspections and maintenance must be carried
out at a safe distance away from an explosive
atmosphere.
Inspection, Maintenance & Repair
Special attention should be given to dust deposits
on the structure, especially in areas where the
profiles come into contact, and should be wiped
clean and care taken not to apply materials that
could create electrostatic charging. Additionally,
the bearings in the trolley rollers and castors
should be checked to ensure they rotate freely.
The structure is predominantly constructed from
aluminum which will not rust. However, there
are steel components used throughout. These
are; fasteners, castors, master-link, trolley rollers,
A-frame height adjustment gearing product (if
fitted) and the height adjustment ratchet (if fitted).
Where there is sign of any rust deposits on the
aluminum structure, it should be wiped clean as
above and, where there is sign of rust on a steel
component, that component should be removed
from use and the structure not used until a
replacement is fitted.
PORTAGANTRY 11000

Bolts, Nuts &
Washers
Cheek Plate
Hockey Stick
Strut Handle
Strut
Stabiliser Leg
Trolley
Beam
Adjustable
Upright
Trap Plate
Leg
Lockable Castors
Leg Brace
The PORTA GANTRY and its constituent components are described in the image below.
Appropriate PPE should be worn: Gloves Protective Footwear Hard Hat
Assembly Instructions

Attaching leg brace
The unit is most easily assembled with the
A-Frames at their lowest height setting
and this is the recommended position to
start from. (A-Frame shown with Geared
elevation and Stabiliser leg attached)
13
The PORTA GANTRY system is delivered flat
packed on a pallet and should include:
2 x A-Frames
1 Trolley
(Stabiliser legs – Option)
Beam (sometimes shipped separately)
Gantry Tool Set (supplied as an option):
Ratchet handle 1/2” sq drive
24mm socket
24mm combination spanner
14mm long series allen key
14mm Hex key socket
Apply the castor brakes
Put brakes on only with protective footwear
ensuring that the castors are in the orientation
shown
Assemble each A-Frame by:
Positioning legs and bolt in place
This illustration demonstrates how an A-frame will
arrive, prior to its assembly.
Lock castors in orientation shown. Do not use hands!
PORTAGANTRY 11000
4a
1 2 3
4 5

Bolt 2
Bolt 1
The gantry beam has adjustment holes to narrow the
footprint of the gantry. If this process is required to
be carried out often then an upgrade to ‘lobed cheek
plates’ can be purchased which allows the gantry to be
assembled as steps 8-21 but with one A-Frame inward
from the end of the beam.
Lay the two A-Frames a beam length apart on a
flat surface in line with each other with the castor
wheels outward and brakes on
Lay the beam on the A-Frames, resting on bolt 1
on each cheek plate
This illustration demonstrates the bolt positions
(1 & 2) for the cheek plates.
Offer one end of the beam to the rear bolt-hole
on the cheek-plate (bolt 1) and insert a bolt
Put on plain washer, spring washer then nut,
finger tight
Offer opposite side of beam to the rear bolt-hole
on the cheek-plate (bolt 1) and insert bolt
Put on plain washer, spring washer then nut,
finger tight
Thread the beam trolley over the other end
of the beam and lock with the friction brake at
approximately center position. If using a gated
trolley, lock with the friction break
Assembly Instructions
76 8
109
8a

Spare Bolt
Tighten both bolts until the spring washer is fully
depressed
Slacken chain block and remove bolt
restraining the trolley
Move trolley to other end of beam and
repeat steps 11-13 for second A-frame
assembly. Then follow step 20
Mechanical Aid
15
Move the trolley to the last beam hole on the side
of the A-frame to be assembled
Insert the spare bolt into the beam, between
trolley and A-frame to be assembled, as shown
Fasten the bolt with the nut to ensure it does not
remove itself
Operate the chain block until the A-frame
assembly is perpendicular to the beam and insert
second bolt into cheek plates
Attach chain block to trolley master-link and attach
the lifting chain to the mechanical aid, as shown
The further the trolley away from the A-frame
the greater the mechanical advantage. Ladder will be required to reach bolt holes.
Mechanical Aid Assembly
PORTAGANTRY 11000
1311
1413a
12

Attach the lifting device to the trolley in
order to avoid having to lift and attach
when gantry is fully erect.
With the help of 2 (or 3) people, scissor
the beam and A-Frame into position
(using the first bolt as a hinge until
A-frame assembly perpendicular to beam)
Repeat the scissor activity at the opposite
end of the gantry - Steps 16-18
If mechanical aid assembly not possible proceed
as follows:
Secure trolley at opposite end of beam to be
assembled and secure by tightening the trolley
knob
Move trolley to other end of beam, opposite to
the end to be raised, and secure by tightening
the trolley knob
Be careful not to trap any fingers in this operation.
The use of a suitable platform ladder
may be required to reach the bolt-hole.
Insert the second bolt into the cheek-plate.
Tighten both bolts until spring washer is fully
depressed, be cautious not to overtighten
For additional safety, a spare bolt can be
temporarily placed in the adjustment point.
Insert and tighten the final beam bolt
Assembly Instructions
Manual Assembly
16 16a
18a
17
18 19

Tighten all bolts to 27 Nm (20 ft lbs) or until spring
washers are fully depressed.
If raising the beam height – leave the two height
adjustment bolts loose on each upright. –see next
section.
Decide on the height required (always using the
lowest setting for the work in hand).
17
Release trolley and castor brakes to position the
gantry over the load, ensuring if possible that the
load is lifted from the center of the beam
Ensure the beam is horizontal and
castors are locked prior to any lift.
The use of a suitable platform ladder may be required.
If the hoist is not already attached to the
suspension point on the trolley, do so now
The gantry is now erect at its lowest height setting.
PORTAGANTRY 11000
21
20 21 21a

Two upright bolts to be removed in Trap Plate
With Geared Handwheel
Two person operation recommended – one on
each A-Frame
Always wear gloves when using this item.
For taller A-Frames a suitable platform ladder
should be used to operate the gearwheel at an
ergonomic height.
The following steps should be done concurrently
on each A-Frame, ensuring that the gantry
uprights are vertical, and the beam is horizontal.
Ensure the castor brakes are engaged
Hold the gear wheel securely
Remove the 2 upright bolts, as shown in
figure 1
Compress center pad with thumbs whilst
holding the wheel firmly.
Rotate the wheel (clockwise to raise,
anticlockwise to lower) to adjust height to
required setting, ensuring that the bolt holes
are aligned, as in figure 2
Release center pad, but continue to hold
wheel securely
Re-secure the 2 upright bolts, nuts and
washers
Check all bolts on the gantry are sufficiently
secure by ensuring all spring washers are fully
depressed
Beam Height Adjustment
Geared Handwheel rotation Release castor breaks
Geared Handwheel rotation
Fig 1
Fig 3 Fig 4
Fig 2

19
With Ratchet System
Two Person Operation Recommended – one on
each A-Frame
Always wear gloves when using this item.
Release Ratchet (Figure 4). Ensure the hook at
the end of ratchet strap is positively engaged
within the bottom hole of the A-frame upright
(Figure 5)
Ensure Castor brakes are engaged.
Remove lower bolt on trap plate
Tension ratchet strap to take the upright/beam
weight
Remove upper bolt on trap plate
Operate ratchet to adjust height to required
setting, ensuring that the bolt holes are
aligned as in figure 6
Re-insert upper bolt and nut/washer assembly
Ease tensioned strap aside, re-insert lower
bolt and secure.
Repeat steps 2-8 on the second A-Frame,
ensuring that the gantry uprights are vertical,
and the beam is horizontal
Check all bolts on the gantry are sufficiently
secure by ensuring all spring washers are fully
depressed
PORTAGANTRY 11000
Operate Ratchet
Ratchet in ‘parked’ position
Fig 6
Fig 7
Fig 4
Fig 5

Medium or Small A-Frame with no
gearing fitted
Two person operation recommended – one on
the bolts and one on the upright.
Always wear gloves when using this item.
Ensure the castor brakes are engaged
Adjust the upright position at one A-Frame by
removing 2 x upright securing bolts and lifting
from the strut handle, as in figure 1
Re-insert bolts and nut/washer assembly’s (do
not over tighten)
Repeat the height adjustment on the second
A-Frame, ensuring that the gantry uprights are
vertical, and the beam is horizontal
Check all bolts on the gantry are sufficiently
secure by ensuring all spring washers are fully
depressed
Beam Height Adjustment
Geared Handwheel rotation Release castor breaks
Beam height adjustment bolts (2 bolts on each upright).
Tighten all bolts to 27 Nm (20 ft lbs) or until spring washers
are fully depressed.
Fig 2 Fig 3
Fig 1