fantastic furniture Chester Queen Bed User manual

Version 1.0
Chester
fantasticfurniture.com.au
Queen Bed

fantasticfurniture.com.au Page 2Page 2
Love it? Share it!
Fantastic buy! Share how it looks at home on Instagram for
your chance to win a $250 Fantastic Furniture Gift Card!
@fantasticfurniture
fantasticfurniture.com.au
Looks like you’ve found
your Fantastic!
We’re thrilled you’ve chosen Fantastic Furniture
to help create a home you’ll love!

Assembly checklist
Useful information
Read through the instructions carefully
before you begin.
Identify and lay out all of the components
before you begin assembly.
! Never use power tools unless specifically instructed. They can damage your components or
hardware if used incorrectly.
! If you are having any diculties assembling your product, missing any hardware or
components please visit our website Help Centre for further assistance.
! Periodically check and re-tighten all fasteners. Check the product care label or website for
product care instructions.
! Never use any glue until you are certain that the parts belong together.
! Bulky items such as wardrobes and bunk beds should be assembled in the room they will be
used as they may not fit through a door once assembled.
! Always use a soft surface (such as carpet or cardboard) when assembling your product to
avoid scratching or damaging the surface of the product.
! The most common mistakes made during assembly are using the wrong hardware or getting
components back to front.
Unless instructed, do not fully tighten screws
until the item is fully assembled.
Make sure you have all the required tools.
Never use power tools unless instructed.
! Please see page 2 for any safety requirements or weight restrictions.
Page 3
fantasticfurniture.com.au

Timber Cross Rail (P5) ; Left Side Rails (P6) ; Right Side Rail (P7) ; Centre Rail (P8) ;
What you need
to assemble the product
Other tools you need:
Phillips head screwdriver;
Headboard (P1)
Timber Cross Rail
(P5)
Footboard (P2)
Leg (P3)
Centre Rail (P8)
Support Leg (P9)
Brackets (P4)
fantasticfurniture.com.au Page 4
Headboard (P1) ; Slats (P12)
Parts list
Box 1 :
Box 2 :
2 x Support Legs (P9) ; End Connectors (P10) ; Centre Connectors (P11) ;
28 x End Connectors (P10) 14 x Centre Connectors (P11)
28 x Slats (P12)
Hardware pack
(Bolt)
4 x M8 x 16mm
(H1)
1 x M5 (Allen Key)
(H2)
(Screw)
2 x M4 x 32mm
(H5)
(Bolt)
14 x M8 x 25mm
(H3)
(Washer)
14 x M8 x 19mm
(H4)
(Felt Pad)
1 x 40 x 20mm
(H6)
(Spring Washer)
4 x M8
(H7)
Left Side Rail (P6)
Support Leg (P9) Leg (P3)
Hardware Pack.
Right Side Rail (P7)
Footboard (P2) ; 4 x Headboard/Footboard Legs (P3) ; 2 x Brackets (P4) ;
Headboard/Footboard
Headboard/Footboard

fantasticfurniture.com.au Page 5
Step 1
Step 2
You will need
Allen Key
(H2)
4 x Washers M8
(H4)
4 x Bolts 25mm
(H3)
(H2)
(H3)
(H4)
(P3)
(P3)
(P3)
(P4)
(P1)
Attach 2 x headboard legs (P3) to the bottom of headboard (P1) and rotate as shown.
washers (H4) by using the allen key (H2). Repeat for the right side rail (P7).
Attach footboard legs (P3) to the bottom of the bracket (P4) and rotate as shown.
Then, attach brackets (P4) to the left side rail (P6) with 2 x bolts (H3) and 2 x
(H2)
(H3)
(H4)
Left Side Rail (P6)
Right Side Rail (P7)
Do not fully tighten the bolts (H3) until step 7.

Step 4
Step 3
fantasticfurniture.com.au Page 6
You will need
2 x Washers M8
(H4)
2 x Bolts 25mm
(H3)
(P8)
Attach 2 x support legs (P9) to the centre rail (P8) with 2 x bolts (H3) and
2 x washers (H4) by using allen key (H2).
Allen Key
(H2)
(P9)
(H2)
(H3)
(H4)
You will need
4 x Washers M8
(H4)
4 x Bolts 25mm
(H3)
Allen Key
(H2)
4 x Bolts 16mm
(H1)
(P1)
(P2)(P6)
(P7)
(P1)
(P6/P7)
(H1)
(H2)
(H2)
(H3)
(H4)
Install 4 x bolts (H1) to the brackets of headboard (P1) by using allen key (H2)
as shown, do not tighten the bolts and keep them 8mm loose. Then attach the side rails
(P6/P7) to the headboard (P1) over the bolts (H1) as shown. Finally, attach the
side rails (P6/P7) to the footboard (P2) with 4 x bolts (H3) and 4 x washers (H4) by
using the allen key (H2). Do not fully tighten the bolts (H3) until step 7.
(P6/P7)
(P2)

Step 6
Adjust to be 10mm gap from floor
to the bottom of support legs.
Slot the centre rail (P8) into the headboard (P1) and footboard (P2).
Rotate 4 x bolts (H3), 4 x washers (H4) and 4 x spring washers (H7) to the headboard (P1)
and footboard (P2) by using alley key (H2). No need to tighten bolts until step 7.
Step 5
You will need
4 x Washers M8
(H4)
4 x Bolts 20mm
You will need
28 x End
Connectors
(P10)
14 x Centre
Connectors
(P11)
28 x Slats
(P12)
(P10) (P10)
(P11)
1
Push 2 end connectors (P10), 2 pcs slats (P12)
and a centre connector (P11) together.
fantasticfurniture.com.au Page 7
(P12) (P12)
Allen Key
(H2) (H3) 4 x Spring Washer
(H7)
(H2)
(H3)
(H7)
(H4)
(P1)
(P2)
(P6)
(P7)
(P8)
(P8)

fantasticfurniture.com.au Page 8
2
3
4
Insert the full slat into the side rail and centre rail one by one.
Sometimes it makes it easier to line up the hole if you press down in the middle of the
slat to flatten it out.
Repeat for every bed slat until finished.

Step 7
You will need
Phillips head
Screwdriver
(not provided)
(H2)
Allen Key
Felt Pad
1 x 40 x 20mm
(H6)
(H5)
(P5)
(P2)
Make sure screws
are fully tightened.
Make sure the inner space is square.
Attach the felt pad (H6) to the centre of centre rail (P8).
Then attach the timber cross rail (P5) to the centre of side rails (P6/P7) by using
2 x screws (H5). Now tighten all the bolts on the centre rail (P8) and tighten bolts on
fantasticfurniture.com.au Page 9
2 x Screws 32mm
(H5)
(H2)
(P1)
(P6)
(H6)
(P8)
(P5)
(P7)
the headboard (P1), footboard (P2) and side rails (P6/P7).

Step 8
Job complete!
In the interest of our environment please dispose
of all packaging thoughtfully.
fantasticfurniture.com.au Page 10