REMKO GSG-4 User manual

REMKO GSG-4
Multi-unit control device
for REMKO GPA-C
Edition GB - P06
Operation
Technology
Original
REMKO
REMKO - powerful like a bear

3
The REMKO GSG-4 control unit is used in combination with an addi-
tional external temperature control (e.g. REMKO ATR-1 or ATR-3) to
connect and control a max. of 4 heaters.
The modes heating, ventilating and resetting the electronic control sys-
tem, can be controlled separately for the individual GPA-C with this unit.
The modes unit operation and burner malfunction are displayed sepa-
rately for each unit by the respective control light.
The control unit is supplied with all accessories to connect a maximum of
4 units. However, the required thermostat control is not included.
Our guarantee becomes null and void if the unit is used improperly
or if modifications are made to the supplied unit.
G
Read these instructions carefully before putting the control unit
into operation and then using it.
G
Description of Device
Unit 1Unit 2 Unit 3 Unit 4
Operating switch
Operating light
Malfunction light
Reset button

4
Mode selector
The mode selector sets the function of the individual units.
0 = OFF
I = Heat
II = Fan
Functionality
Thermostat control is not possible for the mode setting II = Fan!
G
Operating light
The green operating light is illuminated when the operating switch of the
unit is switched to Position I (heating).
Malfunction light
The red malfunction light is illuminated when the unit was switched off
due to a problem with the burner.
Reset button
The reset button releases the safety mechanism of the heater and re-
starts the unit.
Before pressing the Reset button, you should first identify the
cause of the malfunction and fix the problem!
G
If the safety temperature limiter (STB) has switched off the burner, the
STB-RESET button in the inspection room of the heater must also be
pressed (see the operating instructions for the heater).
The REMKO GSG-4 control unit may only be connected to a 7-pole
plug of the GPA-C heating units intended for this purpose.
G

5
Only have the control unit connected and put into operation by
authorised electrical personnel.
1. Assemble the heater following the instructions in the operating
manual.
2. The control unit must be set up in such a way that all heaters are
visible during operation.
3. Establish the electrical connection between the control unit and
the heater in accordance with the wiring diagram (page 6). The
necessary installation material (electrical cables, etc.) must be
supplied by the customer.
Note: The electrical connection between the heater and the control unit
may only be established using the supplied 7-pole plug.
4. Make sure that the control current for the contactor is activated
from the optional external control unit (see the wiring diagram on
page 6).
Note: The integrated contactor (K1) is controlled by the separately
installed external control unit and isolates the respective heater.
Operation that complies with regulations is only assured when a
thermostat (REMKO ATR-1, ATR-3 or ) is installed and connected
for temperature control.
G
Installation and Initial Operation
Safety Hints
ÞBefore working with the control unit, all current-carrying lines must be
free of current!
ÞConnection and service of the control unit may only be performed by
authorised personnel!
ÞThe control unit must be protected from damage and unauthorised
use!
ÞCompliance to VDE 0100 must be assured as well as any additional
requirements of the local EVU!

6
Wiring Diagram GSG-4
H1 = Control light red (burner malfunction)
H2 = Control light green (operation)
K1 = Contactor
R1 = Resistance
S = Operating switch
T1 = Reset button
WS = Plug, 7-pole
We reserve the right to make changes to dimensions and design in the interest of technical progress.
Only have the REMKO GSG-4 control unit installed and put into
operation by authorised personnel in accordance with the rele-
vant regulations.
G
Plug for heater
External thermostat 230 V
Optional accessories

REMKO GmbH & Co. KG
Klima- und Wärmetechnik
D-32791 Lage •Im Seelenkamp 12
D-32777 Lage •PO Box 1827
Phone [phone] - 0
Fax [phone]
E-Mail: [e-mail]
Internet: www.remko.de