Remock Lockey Next Generation Wireless Door Lock with Remote... Operator's manual

NextGenerationWirelessDoorLockwithRemoteControl
User Instruction Manual
Please read carefully the following instruction
for your safety before using the product.
Itisimportanttounderstandhowthislockworksto
useitcorrectly

Warning Elements
When the LED light is flickering and beep signals sounddifferentfrom usual,please change batteries
immediately.( refer to page6)
Please make sure that youdon't drop it or get it wet becauseit's a highly sophisticate product made from
semiconductors.
When the door lock is contacted with water, you can have the risk of electric shock, fire and malfunction of the lock.
Do not install this door lock in the place of heavy humidity, dust or oily smoke to prevent any fire and electric shock.
Youmust not install this door lock in the place where inflammable materials exist
Please do not leave the remote control orthe lock within the reach of infants.
Please change using batteries of the lockbody at the same time to all new batteries AA ALKALINE.
(A mix ofnew and usedbatteries or two different kindsof batteries may cause the malfunction of the lock.)
Pleaseensure you correctly placetwobatteries accordingto the signs of +and -.
Andyou arerecommendednottoreplacebatteriesin presenceofchildren.
Please take out batteries fromthe lock body when the lock is not used for a long time to prevent any
possibility offireand malfunctionoftheproduct
※ Registered remote control's code is not erased even after batteries are changed.
Pleasemake sure abouttheprocedures on registry and deletion ofremote control's codeas provided on
page8. Anyerrors may lead to the malfunction ofthe lock.
You are also required to confirmwhether the remote control works accordingto either registry or deletion of the code.
Please keep in mindthat the remote control can be stolen, so take special care not to lose it.
※ You may keep one of remote controls at a secrete place for emergency.
Never tryto disassemble the body.
This door lock was developed asan assistant lock system for use with a main lockequipment.
Please keep in mindthat twopersons use two remote controls toactivate the door at the same time.
Such a duplicate usemaystop functioning.

NextGenerationWirelessDoorLockwithRemoteControl
User Instruction Manual
Please read carefully the following instruction
for your safety before using the product.
Itis importanttounderstandhowthislockworksto
useitcorrectly

User instruction
Open the battery cover by pushing it to the direction (▼)and then insert two
AA alkaline batteries (referto page 6)
Close the battery cover.
Once the lock is installed, please ensure that the remote control
works properly by testing it outside the door. You have someone
who can monitor the function inside during the test.
(After that, you two switch the position and test it again)
Transmission Distance of the remote control
Bestplace for transmission and reception of radiowave.
Antenna Angle (90¡ with lock body is the best, but may be different according to
circumstance.)
Alarm tone will ring from the lock when the door is "locked or open."
Locking andopeningsignals
▶ Push lock button→ "Pi~ik" (two-syllable rhythms) →the door is locked.
▶ Press open button →"Pik, pik, pik" (repeated single-syllable rhythm) →the
door is open.
▶ If the remote control does not work, please press the button again.
▶ Although it is possible to acknowledge the locking and opening of the door
bysignals, you are recommended to confirm it yourself.
▶
▶
▶
▶
Function of informing the timing to change batteries.
▶ When LED light flickers every 4 seconds and signals sound like cricket, the
batteries must be changed immediately.
▶ If you fail to change batteries in time, the lock would stop functioning
(In this case, our company doesnot take any responsibility for the damage
causedby the discontinued function of the door lock.)
Hand lever.
The hand lever is designed to open easy in emergency such as fire.
Please remember!
4piecesofremotecontrol
arebasicallyregistered
Please register the codes
of these remote controls
again toensure safety.
Please makesurethatyou
have to registerthe code
inthe lockwhenyou
purchaseanadditional
remotecontrol.
(refer topage8).

Composition and name of parts
Photos of the following components are presented
to increase your understanding and may be different
from actual products.
Body Base Steel Plate Latch &Assistant Busing AA Alkaline Battery Remote Control
Components
NAME OF EACH PART.
hand lever
latch with
assistant busing
assembled
remote controller
front plate
rubber packing
LED window:
signaling the
time of batter
change
Battery :
(+, -) Insert after confirmation
battery cover
Antenna :
Variableefficiency
according to th
angle
Openbase steel plate:
delivery after assemble
Battery:
delivery inserted. fix point for
key chain
rear plate
<Lock Body > < Remote Control>

Change of batteries for the lock body
Lock Body
The LED light flickers every 4 seconds to signal the need for battery replacement.
In addition, when signals sound different from usual, you are also required to change batteries as follows:
Locking and opening signals
* Push lock button→ "Pi~ik" (two-syllable rhythms) →the door is locked.
* Push open button →"Pik, pik, pik" (repeated single-syllable rhythm) →the door is open.
Steps for replacing batteries [※ When the LED starts flickering please change the batteries immediately]
Please
insertnew
batteries
at the
interval of
10seconds
(for protec-
tion of ele-
ctronic
circuit.)
LED flickering Push cover in the direction▼ Insert batteries [+,-] confirm operation
Please useonly AA alkaline batteries. The use of magnetic batteries or recharged batteries may induce malfunction of the lock.
Checking procedures after battery replacement
* Please check whether the lock works by using remote controls.
* The LED light and the signals regain their normal mode by recognizing normal battery voltage.
Please check the expiration date of battery(written in the bottom)
Please note that the discharging speed of battery is different according to the storage condition.
Causion

Replacement of Remote Control Battery
Please replace the battery of remote control when the LED light becomes dimmer and the operation speed slows down.
▶ LOCKEY is designed to generate weak electric waves, which
are transmitted through narrow crevices around the door
▶ The standard transmission distance of the remote control is
up to 1.5 meter straightly from the door.
▶ The transmission distance of the remote control from the outdoor
varies with environmental conditions and electric wave background.
(Same conditions from the inside also)
▶ Wireless transmission is very sensitive to other frequency. So the
best location can be changed.
Use a (-)
shaped small
driver
Insert the tip of
driver into a
channel on lateral
sideand slightly
twist the driver to
open the case
Replace battery
(CR 2032)
Make sure the
poles, + or -
Assemble sequence:
front case→rubber
ele'c ciruit board→
backcase
Test
main body and
remote control

You are recommended not to press registration button unless you
want to re-register the codes after losing one of remote controls or to register the newly purchased one.
Pressing the registration button will delete all stored codes.
Caution
How to register or delete the code of
between remote controls and lock body
Registration button
Registration ofR/C
1 Open the battery cover.
2 Thereis registration button in the middleof the left side of battery holder.
3 Press registration button witha stick-like tool for about 2 seconds.
4 The LED light flickers with a sound of "Pi-ri-lik"
5 Press each remote controls for about one second until it makes "pi-ik-" sound.
☞ When you stop taking further steps for more than 15 seconds,
the remote control turns to the normal mode automatically.
6 Pressregistration button forabout one second to resume the registration
7 Registration has been completed. Test the lock using the registered remotecontrols
8 When one of the remote controls do not work, please registeragain
following the same steps as abovementioned
1 In case you lose one of the remote controls, please collect theremaining three for re-registration
2 Please take the same steps as described above for re-registration
3 This means that the lost remote control is deleted registration.
Check if LED light flickers

Please test the four remote controls from out side with leaving the key body inside before installation.
Check the door condition (material, shape and surface)
If the door has an unsmooth surface or its paint peels and if it is a wood door, we cannot guarantee your
security after installation. (In that case, please consult with the dealer)
■ Measurement for installation location.
Check if the lock can fit into the door and its frame.
■ Cleaning the installation place.
Wipe off the dust or moisture on the installation place with alcohol.
(Impurities will undermine adhesion)
■ Inserting busing in the hole of latch.
Install the lock after inserting assistant busing in the hole of latch and combining the body with the completed latch.
■ Notice for the attachment/detachment of the body.
Be careful not let the lock body fall from the installation place to prevent human injury and damage of the lock.
■ Automatic opening
There is function that in case of incomplete installation or operation failure, the lock will be opened
automatically, with warning sound.
Tape can not be re-used.
This tape can not be used once it is attached. So, attach it after reading the installation method enough.
Caution
Establishment common sense

How to install and disassemble
1. Take off the adhesive tape from latch.
2. Push andattach latch todoor pillar. Atthis stagethere isno need to
detach adhesive tape from the body.
3. Now please detach adhesive tape from the body.
4. Fix the body on the positionwhere you want to install it
5. Remove assistant bushing after dismantling combination.
6. Press the adhesive tape to remove the air, so thatthe adhesive
strength between the body and latch will be increased.
* Test the lock using the remote controls
Please try to operate remote controls and check if the
installation was made properly.
* Please do not touch the
installed lock for 24 hours for
better adhesion.
* You can detachit easily from thedoor and carry it when you move to new place.
* Please purchase new latch and base plate with attached adhesive tape at our
distributor shop.
1. Please detach bolts on both sides of base plate from the body by using a cross driver (+).
2. Please cut the base plate attached to door while putting piano string or guitar string
between base plate and door surfaceand then pulling the string slowly.
Please note that if youstop it will not move again.(same method for latch)
3. It is easier to detach adhesive tapewhich is attached to the door after warming it by hair dryer.

▶ ASK SINGLE CONVERSION
▶ 315MHz (±500KHz)
▶ Alkaline AAM size 2 pcs
▶ 6 months based on 20 times per day
▶ -20℃ ~ 60℃ (in no freezing and dew condition)
▶ 5%~80%(in no dew condition)
▶ Number of registered remote controller: 16 different codes can be registered respectively.
▶ ASK SINGLE CONVERSION
▶ 315MHz (±500KHz)
▶ lithium battery CR2032
▶ 12 months based on 20 times per day
▶ -20℃ ~ 60℃ (in no freezing and dew condition)
▶ 5%~80%(in no dew condition)
▶ about 260,000,000
Specification

Warranty
1. We offer after-service for free when the product is broken during the warranty period after it was
installed in compliance with the user instruction manual. You can bring the product to the dealer or us.
2. However we charge fee for the following services even during the warranty period:
Even in the guarantee period, charged repair will be made in the following cases:
a) When there is no evidence on the date of purchase
b) When failure or damage was caused by natural disaster such as fire, earth quake, water
flood. lightening and others.
c) When failure or damage was caused by improper use, attachment, dismantlement, or modification.
d) When failure or damage was caused by careless handling or accidental dropping after purchase.
e) Change of consumables (battery, attached base plate, latch).
f) When failure or damage was due to environmental conditions
g) The product's register number was removed
3. This warranty is intended for the key body and remote controllers.
This warranty does not comment on the matters regarding sales loss caused by the failure or damage
of the product
4. Warranty period
a) The warranty is effective for a period of one (1) year from the date of purchase
b) The date of shipment is considered as the date of purchase in case there is no evidence on the
date of purchase