Assa Abloy NORTON RIXSON CG0M19 User manual

IS-CG0M19 Rev 2 05/22
CG0M19 Intermediate Pivot
3/4" Offset, Handed
Installation Instructions
Copyright © 2022, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in part
without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.
NORTON
RIXSON
Ce produit peut vous exposer au plomb qui, dans l’état de la
Californie, est reconnu pour causer le cancer, des anomalies
congénitales ou d’autres problèmes de reproduction. Pour plus
d’informations, visitez: www.P65warnings.ca.gov.
This product can expose you to lead which is known to the
state of California to cause cancer and birth defects or other
reproductive harm. For more information go to
www.P65warnings.ca.gov.
WARNING
1. Install intermediate pivot.
1. Determine hand of door for proper placement of
intermediate pivot. (Figure 1)
NOTE:
Door should already be hung with top pivot and
bottom pivot or floor closer.
Doors 60" - 90" (152.4cm - 228.6cm) in height
should use one Intermediate pivot; each
additional 30" (76.2cm) warrants an additional
Intermediate pivot.
2. Locate pivot(s) so that it is vertically in alignment
with centerpoint of top pivot and bottom spindle
and mark pivot leaf locations on door and frame.
(Figure 2)
3. Mortise door and frame. (Figure 3) Refer to
template IP50051.
4. Using pivot leaf as a template mark and prepare
mounting holes on door and frame. (Figure 3)
5. Install jamb portion of pivot in frame using five
(5) 1/4-20 x 5/8" FHMS or #14 x 1-1/2" FHWS screws
provided.
6. Install door portion of pivot in door using five (5)
1/4-20 x 5/8” FHMS or #14 x 1-1/2” FHWS screws
provided.
IMPORTANT: It is responsibility of door
and frame manufacturers to check
hardware schedule and prepare doors
and frames. The following instructions
cover field prep.
To Determine Your Hand of Door:
LH RH
Figure 1
1/8" (3.2) Minimum From
Face of Door to Door Stop
Door Stop
R
R
i
i
g
g
h
h
t
t
H
H
a
a
n
n
d
d
D
D
o
o
o
o
r
r
13/16" (20.6) From Face of
Jamb to of Pivot Pin
Door
Jamb
C
L
5/16
(7.9) 5/16
(7.9)
1/4
(6.8)
3/4" (19) From Face of
Door t L o C of Pivot Pin
3/4" (19) From Door
Edge t
L
o C of Pivot Pin
Figure 3
Figure 2
Approved 2022-05-16

IS-CG0M19 Rev 2 05/22
Copyright © 2022, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in part
without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.
2
CG0M19 Intermediate Pivot
NORTON
RIXSON
2. To adjust door height:
1. Remove arm cap and loosen locking screw of
bottom pivot arm. (Figure 6)
2. Remove hex cap from bottom of intermediate
pivot(s). (Figure 5)
3. Turn stud screw clockwise to raise the door to
desired height. (Figure 5)
4. Using shims furnished with bottom arm, fill gap
between arm and bottom pivot floor portion.
(Figure 6)
5. Turn stud screw counter clockwise until door rests
on shims. (Figure 5)
6. Tighten locking screw of bottom pivot. (Figure 6)
NOTE: Open and close door several times.
Make shim adjustments until door swings
freely.
7. Re-tighten locking screw and replace arm cap.
(Figure 6)
8. Replace hex cap of intermediate pivot. (Figure 5)
Hex Cap Shim
Locking Screw
Arm Cap
Arm Cap Screw
Stud Screw
Figure 5
Floor Portion
Spindle
Jamb
Portion
Top
Pivot
Intermediate
Pivot
1/8"
(3.2mm)
Clearance
Jamb
Door
Door
Portion
Arm
Frame Header
Door
Floor
Door
Plumb Line
Figure 6
Right Hand Shown
Figure 4
Approved 2022-05-16

IS-CG0M19 Rev 2 05/22
Copyright © 2022, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in part
without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.
3
CG0M19 Intermediate Pivot
NORTON
RIXSON
Template IP50051
NortonRixson.com
TEMPLATE NUMBER REV DATE
02/22
NORTON RIXSON NORTON RIXSON
3/8
9.5
1-7/16
(36.5)
2-1/2
(63.5)
3-9/16
(90.5)
4-5/8
(117.5)
1-15/16
(49.2)
1-1/8
(28.6)
13/16
(20.6)
5/16
(7.9)
5"
(127)
5"
(127)
7/16
(11.1)
1-1/8
(28.6)
2-1/2
(63.5)
3-7/8
(98.4) 4-9/16
(115.9)
3-15/32
(88.1)
1-17/32
(38.9)
1-1/8
(28.6)
5/16
(7.9)
13/16
(20.6)
2-1/8
(54)
DOOR LEAF JAMB LEAF
AA
NOTES:
Do not scale drawing.1.
Dimensions are given in inches (mm).2.
Pivot drilled for 1/4-20 x 5/8" FHMS or #14 x 1-1/2" FHWS.3.
Right hand shown. Left hand opposite.4.
2-3/32
(53.2)
CG0M19 Intermediate Pivot
3/4" Offset Hung
1
IP50051
Copyright © 2022, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved.
Reproduction in whole or in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.
1/8
(3.2)
13/16
(20.6)
R 3/16
(4.8)
5/16 (7.9)
5/16 (7.9)
1/4
(6.4)
3/4
(19.1)
3/4
(19.1)
VIEW FROM BOTTOM OF DOOR LOOKING UP
SECTION A-A
SCALE 1 : 1
Bevel Edge Of Door
1/8" in 2"
(3.2 in 50.7)
Door
Frame
Min. Clearance
Approved 2022-05-16

IS-CG0M19 Rev 2 05/22
Norton Rixson is a brand associated with ASSA ABLOY Accessories and Door Controls Group, Inc., an ASSA ABLOY Group
company.Copyright © 2022, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or
in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.
Technical Product Support:
Monroe, NC 28112 USA
Phone: [phone] ext: 2
[e-mail]
NortonRixson.com
NORTON
RIXSON
Approved 2022-05-16