resideo Lyric RCHW3610WF User manual

WIFI® WATER LEAK AND
FREEZE DETECTOR
Installation Guide
CHW3610W, CHWES4,
RCHW3610WF,
RCHWES4
Read and save these instructions
Need help?
• Web: www.resideo.com
• Phone: 18004681502

2
1 Download the Resideo app
Search for Resideo in the App Store or
Google Play.
After downloading, launch the app,
register (if necessary), go to Menu, and
then go to Add New Device.
2 Install batteries
The detector is powered by 3 AA batteries (included). Open the battery
cover on the detector and install the batteries.
When replacing the cover, press firmly
around the edges to ensure a snug fit.
Note: The cable sensor jack is NOT
for plugging in a power adaptor.
Doing so could damage
the detector.
Cable
sensor jack
GET IT ON

3
3 Connect
Pair and name your detector
1 Under Add New Device, select Water Leak and
Freeze Detector.
Note: Make sure Bluetooth is enabled on your
mobile device and that the detector’s LED is
blinking blue. If it is not, see the Reset section.
2 Provide a location for your detector. Press
NEXT.
3 The detector will now pair with the app.
Note: If you have more than
one detector, you will need
to connect each detector
individually.
4 An audible alert will sound
and your detector’s LED will
turn solid blue to indicate
your detector is paired. Press
NEXT.
5 Create a custom name for
the detector or select one
from the list. Press NEXT.

4
Connect to WiFi
1 Choose your network from the list. Press NEXT.
2 Enter your WiFi password, if necessary. Press
NEXT.
3 When connected to WiFi, the LED will turn solid
green for 5 minutes, then turn off to preserve
battery life.
Note: If you remove and replace the detector’s
batteries, it will reconnect to your WiFi network
automatically.
4 Configure
Continue to follow instructions in the app to
configure your detector.
Select the alert levels you want for high and low
humidity and temperature warnings, or keep the
preset levels. Identify the people you want notified
in case of an alarm. These settings can be updated
at any time using the app.

5
5 Placement
Place the bottom of your detector flat on the floor or a surface.
For wall mounting, use the included screw and hang the
detector on the bottom cover’s mounting keyhole.
Optional cable sensor
To install the optional cable
sensor, remove the sensor
jack plug and insert the cable
sensor. Insert the sensor jack
plug at the end the cable
sensor.
Accessory cable sensors (sold
separately) can be connected
to extend the cable and
increase water sensing area.
The entire length of cable is an extended sensor. You
can hang the detector from the wall or place both the
detector and cable sensor on the floor.
Note: The cable sensor jack is NOT for plugging in a
power adaptor. Doing so could damage the detector.
Sensors
Mounting
keyhole
Cable
sensor jack
Sensor jack
plug

6
Leak detected
by device
30 day rolling
temperature trends
Low temperature
detected by device
WiFi connection failure
Resideo app experience
Below are a few examples of the Resideo app screens you will see as
you use the Water Leak and Freeze Detector.
Operation
Common uses

7
Status LED
The detector has an LED that gives device status.
LED Detector state
During installation
Blinking Blue Powering up and connecting to Bluetooth.
Solid Blue Paired with Bluetooth.
Blinking Green Connecting to WiFi network.
Solid Green Has power, WiFi connection, and is operating
normally.
Note: LED turns off after 5 minutes to preserve
battery life.
Solid Red Failed to connect to WiFi.
During operation
Blinking Red Detected a leak.
In case of an alert
To preserve battery life, it can take up to 1 minute for the detector to
sense a leak.
You can mute the detector by pressing the Mute button in the app or
removing the batteries or cable sensor from the detector. The mute
command may take up to 1 minute to reach the detector.
After you’ve addressed the cause of the alert, wipe dry the detector and
cable sensor and put them back in place. Replace batteries if they were
removed.
Reset
Use one end of a paperclip to press and hold into the reset hole for
5 seconds to reset WiFi, detector settings, and to re-start Bluetooth
pairing. The LED will blink blue.
Press and hold the paperclip into the reset hole for 15 seconds to
restore factory defaults. The LED will blink blue.

www.resideo.com
© 2022 Resideo Technologies, Inc. All rights reserved.
This product is manufactured by Resideo Technologies, Inc. and its affiliates.
Tous droits réservés. Ce produit est
fabriqué par Resideo Technologies, Inc.
et ses sociétés affiliées. Imprimé aux
États-Unis
Todos los derechos reservados. Este
producto es fabricado por Resideo
Technologies, Inc. y sus afiliados.
Impreso en EE. UU.
Resideo Technologies, Inc.
1985 Douglas Drive North, Golden Valley, MN 55422
1-800-468-1502
33-00381EFS—02 M.S. Rev. 07-22 | Printed in United States
33-00381EFS-02
FCC Regulations
§ 15.19 (a)(3)
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
§ 15.21
Changes or modifications not expressly approved by the party responsible for compliance could void the user‘s
authority to operate the equipment.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
IC Regulations
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and
Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference that may cause undesired operation of the
device.
IC Radiation Exposure Statement:
This equipment complies with IC RSS102 radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator & your
body.
The operation of this equipment is subject to the following two conditions: (1) this equipment or device may
not cause harmful interference, and (2) this equipment or device must accept any interference, including
interference that may cause undesired operation.

CHW3610W, CHWES4,
RCHW3610WF,
RCHWES4
Veuillez lire le mode d’emploi et
le conserver en lieu sûr
Guide de démarrage
DÉTECTEUR DE GEL ET
DE FUITES D’EAU WIFI®
Besoin d’aide?
• Web : www.resideo.com
• Téléphone : 1 800 4681502

10
GET IT ON
1 Téléchargez l’application Resideo
Recherchez l’application Resideo
dans l’App Store ou Google Play.
Après le téléchargement, lancez
l’application, inscrivez-vous (le cas
échéant), puis cliquez sur Menu et
Add New Device (Ajouter un nouvel
appareil).
2 Installez les piles
Le détecteur est alimenté par 3 piles
AA (fournies). Ouvrez le couvercle
du compartiment des piles du
détecteur et installez les piles.
Pour remettre le couvercle en
place, appuyez fermement sur les
bords pour bien ajuster.
Remarque : La prise du câble de détection
n’est PAS conçue pour être branchée dans un
adaptateur de courant. Vous risqueriez d’endommager
le détecteur.
Prise du câble
de détection