Full face benets in a compact size
ResMed’s AirFit™ F10 full face mask is part of ResMed’s AirFit range – the right fit for you.
Its lightweight, streamlined design enhances comfort and ease-of-use, while its headgear
and frame work in synergy, to deliver the same performance and stability you have grown to
trust in a ResMed traditional full face mask.
ResMed.com
• Remove the elbow from the mask by
pressing the side buttons and pulling it out.
• Take off the lower headgear straps and hold
the cushion to the face. Align the bottom
with the crease of the chin and the top
with the corner of the eye.
• Then pull the headgear over the head.
• Undo the fastening tabs on the upper
headgear straps.
• Adjust both straps evenly until the mask
feels stable, then reattach the tabs.
2
1
• Adjust the lower headgear straps evenly
until the mask feels stable.
• The tting should be rm yet comfortable.
Do not over-tighten.
• Connect device air tubing to the elbow, then
attach the elbow to the mask by pressing in
the side buttons, then push it into the mask.
• Turn on the device so it blows air.
• The patient now lies down to make any
nal adjustments if required.
3
6
7
5
4
• Bring the lower straps below the ears and
loop the headgear into the lower hooks on
each side of the frame.
• Undo the tabs on the upper headgear straps.
• Reposition both straps evenly, only enough
so a seal is achieved, then reattach the tabs.
• The mask is now ready to use.
Additional options
• Position the lower part of the headgear over or under the hair to suit the hairstyle preference.
• Optional soft sleeves may be assembled for even more comfort on the cheeks.
Note: For more d etails, refer t o the AirFi t F10 User Guide.
*ResMed internal study of existing ResMed patients, conducted between 25 July and 4 September, 2013 comparing their ResMed traditional full face mask with AirFit F10.
Proven performance
The dual-wall Spring Air™cushion
provides a secure seal for better
performance. When asked about
AirFit F10’s seal and stability, the
majority of patients we spoke to, told
us that it outperformed their ResMed
traditional full face mask.*
Ease-of-use
The mask’s four-part design makes
it easy for you to demonstrate and
for patients to take apart, clean and
reassemble. Its intuitive design
seamlessly integrates into your
patient’s bedtime routine.
Superior comfort
AirFit F10’s sleek, lightweight design
gives patients a clear line of sight so they
can read, watch TV or even wear glasses
while wearing the mask. In fact, 75%
of patients found AirFit F10 to be more
comfortable than their current ResMed
traditional full face mask.*
ResMed Ltd
1 Elizab eth Macar thur Drive
Bella Vi sta NSW 2153 A ustralia
Distributed by : ResMed Ltd , Bella Vista , NSW, Australi a. See ResMed .com for ResM ed locatio ns worldwid e. AirFit, S oftEdge a nd Spring Air ar e
trade marks of Res Med Ltd. Sof tEdge and Sp ring Air Technol ogy are regis tered in the U. S. Patent an d Tr ademark Of fice. Pro duct availabil ity may var y
acros s regions. Sp ecificatio ns may change w ithout not ice. © 2014 ResM ed Ltd. 1017249 /2 2014-0 3
Fitting guide for AirFit F10 Optimal cushion positioning
ResMed.com
Align the bottom of the cushion with the crease
of the chin and the top of the cushion with the
corner of the eye.
AirFit F10 sits on the nose at, or below, eye level.
1 2
