ResMed AirFit N30i User manual

English
Français
Español
Português
User guide
QuietAir
USER GUIDE
P

English 1
ENGLISH
A
Elbow
F
P30i pillows cushion
B
Elbow ring
1
Vent
C
Headgear
2
QuietAir vent (removable)
D
Frame
3
Side buttons
E
N30i nasal cushion
4
Sleeve
Intended use
The AirFit N30i and AirFit P30i masks are intended to be used by patients
weighing more than 66 lb (30 kg) who have been prescribed non-invasive
positive airway pressure (PAP) therapy such as CPAP or bi-level therapy.
The masks are intended for single patient re-use in the home and
multi-patient re-use in the hospital/institutional environment.
Please read the entire guide before use.
Before using your mask
Remove all packaging and inspect each mask component for visible
deterioration.
Use the fitting template to assist in selecting the right size cushion and
frame.

2
Fitting your mask
1. Pull the frame and headgear over your head until the elbow is
positioned on top and the headgear is behind your head.
2. Place the cushion under your nose.
For the AirFit P30i mask, align the pillows into your nostrils.
3. Tighten or loosen the headgear until the cushion fits comfortably
under your nose.
4. Squeeze the side buttons on the elbow and detach from the frame.
Connect the air tubing from your device to the elbow, then reattach to
the frame.
Adjusting your mask
•When using the mask, air will flow out of the vents in the cushion and
elbow. If air leaks from the side or top of the cushion, adjust the mask
fitting to improve the seal.
•You can position the top of the frame forward or backwards over your
head until the mask feels comfortable.

English 3
Sizing the mask frame
If the mask frame falls back over your head or sits too close to your ears,
try a small frame size. If the mask falls forward on your head or sits too
close to your eyes, try a standard frame size.
Disassembling your mask for cleaning
If your mask is connected to a device, disconnect the device air tubing
from the mask elbow.
1. Pull the cushion from the frame.
2. Undo the fastening tabs on the headgear strap and pull it from the
frame.
3. Squeeze the side buttons on the elbow and detach from the frame.
Note: For the AirFit P30i mask, the QuietAir vent can be removed to allow
inspection of the vent holes.
Cleaning your mask
After each use: Cushion
Weekly: Headgear, frame and elbow
1. Soak the components in warm water with a mild liquid detergent.
Ensure that there are no air bubbles while soaking.
2. Hand wash the components with a soft bristle brush. Pay particular
attention to the vent holes.

4
3. Thoroughly rinse the components under running water.
4. For the frame sleeves, squeeze with a clean towel to remove excess
water. For the AirFit P30i mask, shake the QuietAir vent to remove
any excess water. Leave the components to air dry out of direct
sunlight.
If the mask components are not visibly clean, repeat the cleaning steps.
Reassembling your mask
1. Connect the elbow into the top of the frame until it clicks.
2. Insert the headgear strap into the frame and fold the fastening tabs
backwards.
3. Insert the ends of the frame into the cushion, ensuring that the arrows
on the cushion and frame are aligned.
Note:
•If the elbow ring detaches, re-insert into the top of the frame.
•If the QuietAir vent is removed from the AirFit P30i mask, reinsert it
into the cushion.
WARNING
•The mask is not suitable for patients requiring life support ventilation.
•To avoid affecting the safety and quality of therapy, the mask vents must be kept clear
to protect against rebreathing. Regularly inspect the vents to ensure they are kept
clean, undamaged and clear of blockages.
•The mask must be used under qualified supervision for patients who are unable to
remove the mask by themselves. The mask may not be suitable for those prone to
aspiration.
•Regularly clean your mask to maintain the quality of your mask and to prevent the
growth of germs that can adversely affect your health.
•Visual criteria for product inspection: If there is any visible deterioration of a mask
component (cracking, crazing, tears etc.), the component should be discarded and
replaced.
•Only use compatible CPAP or bi-level therapy devices. The technical specifications of
the mask are provided for healthcare professionals to determine compatible devices.
Use with incompatible devices may affect the performance or safety of the mask.

English 5
WARNING
•Discontinue using the mask if you have ANY adverse reaction and consult your
physician or sleep therapist.
•The mask is not intended to be used simultaneously with nebulizer medications that
are in the air path of the mask/tube.
CAUTION
•Remove all packaging before using the mask.
•Using a mask may cause tooth, gum or jaw soreness or aggravate an existing dental
condition. If symptoms occur, consult your physician or dentist.
•When fitting the mask, do not overtighten the headgear as this may lead to skin
redness or sores around the mask cushion.
•The mask should not be used unless the device is turned on. Once the mask is fitted,
ensure the device is blowing air to reduce risk of rebreathing exhaled air.
•As with all masks, some rebreathing may occur at low pressures.
•Always follow cleaning instructions and only use a mild liquid detergent. Some
cleaning products may damage the mask, its parts and their function, or leave harmful
residual vapours. Do not use a dish washer or washing machine to clean the mask.
•Do not iron the headgear as the material is heat sensitive and will be damaged.
Technical specifications
Compatible devices
For a full list of compatible devices for this mask, see the Mask/Device Compatibility List
at ResMed.com/downloads/masks.
Pressure-flow curve:
Pressure
(cm H
2
O)
Flow
(L/min)
4
20
9
31
15
41
20
49
25
55

6
AirFit N30i
AirFit P30i
Mask setting options:
For AirSense, AirCurve or S9
Therapy Pressure:
Pillows
4 to 25 cm H
2
O
Pillows
4 to 25 cm H
2
O
Resistance: Drop in pressure measured (nominal)
at 50 L/min
0.4 cm H
2
O
0.4 cm H
2
O
at 100 L/min
1.7 cm H2O
1.5 cm H2O
Sound: Declared dual-number noise emission values in accordance with ISO4871:1996
and ISO3744:2010. A-weighted sound power level and A-weighted sound pressure level at
a distance of 1 m, with uncertainty of 3 dBA, are shown
Sound power level
Sound pressure level
24 dBA
17 dBA
21 dBA
14 dBA
Environmental conditions:
Operating temperature: 41°F to 104°F (5°C to 40°C)
Operating humidity: 15% to 95% non-condensing
Storage and transport temperature: -4°F to 140°F (-20°C to +60°C)
Storage and transport humidity: up to 95% non-condensing
Service life: The service life of the mask system is dependent on the intensity of usage,
maintenance, and environmental conditions to which the mask is used or stored. As this
mask system and its components are modular in nature, it is recommended that the user
maintain and inspect it on a regular basis, and replace the mask system or any
components if deemed necessary or according to the ‘Visual criteria for product inspection’
in the ‘Warning’ section of this guide.
Note: The manufacturer reserves the right to change these specifications without notice.
Storage
Ensure that the mask is thoroughly clean and dry before storing it for any length of time.
Store the mask in a dry place out of direct sunlight.
Disposal
This mask does not contain any hazardous substances and may be disposed of with your
normal household refuse.
Reprocessing the mask between patients
Only Sleep Lab Mask (SLM) variants of the mask system are intended for multi-patient
re-use. When using between patients, these masks must be reprocessed according to
cleaning and disinfection instructions available on ResMed.com/downloads/masks.

English 7
Symbols
The following symbols may appear on your product or packaging:
Nasal cradle mask
Nasal pillows mask
QuietAir vent
Device setting - Pillows
Cushion size - small
Cushion size - medium
Cushion size - large
Cushion size - wide
Cushion size - small wide
Standard frame
Small frame
This product is not made with natural rubber latex.
Caution, consult accompanying documents.
See symbols glossary at ResMed.com/symbols.
Limited Warranty
ResMed Ltd (ResMed) warrants that your ResMed mask system
(including mask frame, cushion, headgear and elbow) will be free from
defects in material and workmanship from the date of purchase for 90
days, or in the case of disposable masks and disposable mask
components for 7 days. This warranty is only available to the initial
consumer. It is not transferable. If the product fails under conditions of
normal use, ResMed will repair or replace, at its option, the defective
product or any of its components. This limited warranty does not cover:
a) any damage caused as a result of improper use, abuse, modification or
alteration of the product; b) repairs carried out by any service organization
that has not been expressly authorized by ResMed to perform such
repairs; and c) any damage or contamination due to cigarette, pipe, cigar
or other smoke. Warranty is void on product sold, or resold, outside the
region of original purchase.