ReSound LiNX Quattro MIH User manual

Quick guide
ReSound LiNX Quattro™ MIH

Product: ReSound LiNX Quattro
Model: MIH
Serial number (R):
_______________________________
Serial number (L):
_______________________________
Battery size: 312 or 13
My hearing aid information
Volume control (I) :
(if set up by your hearing care professional)
ACTION RESULT
Rotate forward
(toward your face) Volume increases
Rotate backward
(away from your
face) Volume decreases
Program button (A):
ACTION RESULT
SHORT push Program change
LONG push
Activate streaming
(if enabled by
professional)
PROGRAM WHEN TO USE BEEPS
11
22
33
44
Programs:
(if set up by your hearing care professional)

Get to know your hearing aid
A. Push button (optional)
B. Battery door/
On-O switch
C. Removal cord (optional)
D. Sound outlet
E. Wax filter
F. Vent
G. Microphone sound inlet
H.Microphone in helix tubing
I. Volume control (optional)
J. Serial number
K. Manufacturer
View ReSound hearing aid tutorial videos at youtube.com/resoundus.
K
J
C
H
F
Manufacturer
XXXX
B
D
I
A
C
H
H
F
G
D
E
B

Getting started: On/O function
ON: Insert battery & completely
close battery door (B).
Program 1 will be active.
OFF: Open the battery door (B).
Use fingertip to pull it all the way.
ON
OFF
What you need to know Inserting/Replacing the battery:
1. Open the
battery door (B)
completely by
using your
fingertip.
2. Remove protective sticker from
battery and wait two minutes
before inserting
the battery into
the hearing aid to
allow full activation of the battery.
3. Insert the new battery
with the positive side
(flat side) in the correct
position, as shown.
4. Gently close the battery door (B).
If it doesn’t close easily, check to
see if the battery is upside down.

For changing HF3 wax guard (E),
complete the following steps:
1. Brush the sound
outlet area with
the sound outlet
pointed down.
2. Insert the threaded end of the wax
guard tool into the used wax guard,
and rotate clockwise.
3. Gently pull until
the used guard is
removed.
Insertion: To insert the new wax
guard, gently press the replacement
side of the wax guard tool straight
into the hole of the sound outlet until
the outer ring lies flush with the
outside of the receiver. Pull the tool
straight out. The new wax guard will
remain in place.
Daily: Clean your hearing aid.
Keep your hearing aids dry. Clean
the hearing aids using a soft cloth
or tissue.
Monthly: Change the wax guard (E)
or see your hearing care professional.
For changing the white wax guards,
complete the following steps:
Removal: Insert the removal side
of the wax guard tool into the used
wax guard so that the shaft of the
tool is touching the rim of the wax
guard. Slowly pull the wax guard
straight out.
4. Discard
the used
guard in
the slot
located
in the wax guard kit by pressing it
into the center, sliding it to one end
of the slot, and pull until the filter
is discarded.
5. Flip the wax guard
tool around, locate
a new guard in the
dial, and press the
tip of the tool into
the center of the dial.
6. Gently pull the new
filter out of the dial.
7. Press the new guard to the canal
tip of the hearing aid. Move the
tool gently side to side and pull it
away from the hearing aid.
Regular care & maintenance
removal side replacement side
Wax guard tool

Beep/tone indicators
View ReSound hearing aid tutorial videos at youtube.com/resoundus.
BEEP/TONE INDICATION ACTION REQUIRED
Ding, ding, ding, dong Low battery Change battery
Ding (5 or 10) Hearing aid is starting up After dings cease,
hearing aid is turned on
Ding-ding,
ding-ding, etc.
Hearing aid is in flight mode Use in flight mode if
desired, or open-close
battery door (B) to exit
flight mode
Ripple tone Hearing aid is in
streaming mode
Use with wireless
accessory or press multi-
function button to exit
streaming mode

If there are any other problems not mentioned in this guide, please contact
ReSound or your hearing care professional.
Troubleshooting
View ReSound hearing aid tutorial videos at youtube.com/resoundus.
SYMPTOM CAUSE POSSIBLE REMEDY
No sound Battery door not closed
Dead battery
Battery door will not close
Blocked wax guard
Turn on by closing the battery door (B)
Replace battery
Insert battery properly
Replace wax guard (E) or consult your
hearing care professional
Not loud
enough
Blocked sound outlet
Change in hearing, volume
too low
Excessive ear wax
Change wax guard (E) or consult your
hearing professional
Consult your hearing care professional
Consult your hearing care professional
Excessive
whistling/
feedback
Incorrect placement in ear
Excessive ear wax
If none of the above
Re-insert hearing aid carefully
Clean guard/consult your hearing
care professional
Consult your hearing care professional

401228011 Rev B 2020.01
ReSound Government Services
8001 E. Bloomington Freeway
Bloomington, MN 55420
1.800.392.9932
www.resound.com/veterans
Manufacturer according to FDA:
ReSound North America
8001 E. Bloomington Freeway
Bloomington, MN 55420
1.888.735.4327
resound.com
For more information
Refer to the user guide included in
your hearing aid box.
Your hearing care professional can
be reached at:
View ReSound hearing aid tutorial
videos at youtube.com/resoundus.
Flight mode:
(if set up by your hearing care professional)
Some airlines prohibit the use
of wireless hearing aids (RF
transmitters) onboard. If required
by your airline, enable flight mode:
Disable wireless operation by
opening and closing the battery
door three times within ten seconds
(open-close, open-close, open-close).
Your instruments will now be in flight
mode.
The hearing aids must function in
flight mode for ten seconds before
wireless operation can be re-enabled.
To re-enable wireless operation,
open and close the battery door one
time and wait thirty seconds before
opening the battery door again to
avoid accidentally entering flight
mode again.