ReSound LINX 3D User manual

Quick guide
ReSound LiNX 3D™ IIC

Product: ReSound LiNX 3D
Model: IIC
Serial number (R):
_______________________________
Serial number (L):
_______________________________
Battery size: 10A
My hearing aid information

A. Microphone
B. Battery door
C. Retrieval line
B
A
C
Get to know your hearing aid
XXXXXXXXXX
View ReSound care and maintenance videos at
http://www.youtube.com/user/resoundus
D. Manufacturer
E. Serial number
F. Model
F
E
D
LTxIIC
GN ReSound

Getting started: On/O function
ON: Insert battery & completely
close battery door (B).
Program 1 will be active.
OFF: Open the battery door (B). Use
fingertip to pull it all the way.
ON
OFF
What you need to know Inserting/Replacing the battery:
1. Open the battery
door (B) completely
by using your fingertip.
2. Remove protective sticker from
battery and wait 2 minutes before
inserting the
battery into the
hearing aid to
allow full activation of the battery.
3. Insert the new battery
with the positive side
(flat side) in the correct
position facing out.
4. Gently close the battery door. If it
doesn’t close easily, check to see
if the battery is upside down.

SYMPTOM CAUSE POSSIBLE REMEDY
No sound Battery door not closed
Dead battery
Battery door will not close
Blocked wax filter
Turn on by closing the battery door (B)
Replace battery
Insert battery properly
Replace wax filter or consult your
hearing care professional
Not loud
enough
Blocked sound outlet
Change in hearing, volume
too low
Excessive ear wax
Change wax guard or consult your
hearing professional
Consult your hearing care professional
Consult your hearing care professional
Excessive
whistling/
feedback
Incorrect placement in ear
Excessive ear wax
If none of the above
Re-insert hearing aid carefully
Clean guard/consult your hearing
care professional
Consult your hearing care professional
If there are any other problems not mentioned in this guide, please contact
ReSound or your hearing care professional.
Troubleshooting

Daily: Clean your hearing aid.
Keep your hearing aids dry. Clean
the hearing aids using a soft cloth
or tissue.
removal side replacement side
Wax guard tool
Monthly: Change the wax guard or
see your hearing care professional.
For changing CeruSTOP™(white) wax
filters, complete the following steps:
Removal: Insert the removal side
of the wax guard tool into the used
wax guard so that the shaft of the
tool is touching the rim of the wax
guard. Slowly pull the wax guard
straight out.
Regular care & maintenance
For changing HF3 wax filters,
complete the following steps:
1. Brush the sound
outlet area with
the sound outlet
pointed down.
2. Insert the threaded end of the wax
filter tool into the used wax filter,
and rotate clockwise.
3. Gently pull until
the used filter is
removed.
Insertion: To insert the new wax
guard, gently press the replacement
side of the wax guard tool straight
into the hole of the sound outlet
until the outer ring lies flush with the
outside of the receiver. Pull the tool
straight out. The new wax guard will
remain in place.

400706011 Rev A 2017.02
ReSound Government Services
8001 E. Bloomington Freeway
Bloomington, MN 55420
1.800.392.9932
www.resound.com/veterans
Manufacturer according
to FDA:
ReSound North America
8001 E. Bloomington Freeway
Bloomington, MN 55420
1.888.735.4327
resound.com
Manufacturer according
to Health Canada:
ReSound Canada
303 Supertest Road
Toronto, Ontario M3J 2M4
1.888.737.6863
resound.com
For more information
Refer to the user guide included in
your hearing aid box.
Your hearing care professional can
be reached at:
View ReSound hearing aid tutorial
videos at youtube.com/resoundus.
4. Discard
the used
filter in
the slot
located
in the wax filter kit by pressing it
into the center, sliding it to one
end of the slot, and pull until the
filter is discarded.
5. Flip the wax filter
tool around, locate a
new filter in the dial,
and press the tip of
the tool into the
center of the dial.
6. Gently pull the new
filter out of the dial.
7. Press the new filter to the canal tip
of the hearing aid. Move the tool
gently side to side and pull it away
from the hearing aid.