Ress SK7 User manual

Camera SK7
Art.-Nr. 2519
1. Delivery contents
- Monitor SK7
- 20 meter cable
- Charger
- SD-card
- Carrying straps
- Sun protection
2. Safety Notes
- The video inspection system is not waterproof!
- The video inspection system is not for use in the medical field!
- Any kind of reparations on inside of the unit, must be carried out, exclusively by qualified staff!
(If required, contact the RESS-customer service)
- The connection and disconnection, the respective components of the system, must always
be carried out without power supply!
- The video inspection system must be switched off after it has been used!
- To clean the monitor and the housing, please use a damp, clean cloth to prevent
scratches! We recommend a microfibre cloth.
- Please avoid contact with water of any kind.
- Please avoid collisions at any time! (use strap)
- Do not use aggressive cleanser for cleaning!
- Do not use the inspection system near a strong magnetic field!
- Avoid temperatures above 40 degrees Celsius. Only accomplish an inspection if heating is
switched off!
- This product has a certificate of conformity according to the guidelines 2004/108/EG.
4 RESS

3.3 Start-up
Stabilizer for the basic setting of the
Rotary-Ball-Camera.
2. With the power switch you put the device
in operation.
1. Reset meter counter
RESS 7
The fixing brake clamps the cable to prevent an unwinding
during an inspection or transporting. Always clamp the
cable with the fixing brake, before letting go of the cable
during an inspection.
The meter counter will start automatically as soon as you
begin to unroll the cable. With the zero button (1) the
counter can be reset to zero anytime.
The Rotary-Ball-Camera can perform swinging or pivoting
movements or can run only in one direction. This can be
adjusted by using the stabilizer. The left controller is
responsible for the rotational movement, and the right one
for the pivoting movement. Turn the trimmer until the
desired setting is achieved. For a detailed description see
manual of the camera head.
The working temperature for the camera cable should
not fall below +5°C. There is a risk of cable breakage.
Connect the jack of the camera to the 12-pin connector on
the camera head. Please make sure that the groove guide
of the plug matches with the socket. Screw the plug with
the threaded screw tight.
Connect the cable quick plug with the socket of the camera
head. Place the the white arrow with the open lock above
the white mark, connect and lock by a quarter turn
clockwise. To unlock turn anticlockwise.
12 pin:
Quick plug:

6. Memory card
7. Technical data
Overall dimension 307 x 285 x 200 (L / W / H)
Weight ca. 4,9 kg
Cable length 20 meters
Monitor 7" TFT color screen 156 x 86 mm
Storage media 4 GB SD-card
1 photo 32 kb (720x576 pixel)
120 second video 42 MB
Power supply NiMh 12 V/3200 mAh
Voltage monitoring LC-Display
Operating time ca. 3 hours (depending on the camera head that is being used)
Charging time ca. 5 hours
10 RESS
The SD-card slot is on the right side of the monitor unit. The
delivery contents an SD-card, where photos and movies
are saved onto.
Insert the SD-card with the writing at bottom until you hear
a "click". Now the SD-card is locked and ready to be used.
To remove, please push the SD-card until you hear a "click"
again. The card will pop out automatically. Now it can be
connected to a reading device (not supplied).
Please note that the monitor supports SD-cards of
1-8 GB.

RESS GmbH & Co. KG
Am Hasselbruch 28
D-32107 Bad Salzuflen
Tel. ++ 49 52 08 / 91 27 0
Fax ++49 52 08 / 80 30
[e-mail]
Internet-Shop: www.ress.de 14.09.2018
RESS
The Producer
Visual Inspection Sweep Instruments Measuring Instruments