RetroSound Santa Cruz Troubleshooting guide

RADIO FACE QUICK START GUIDE
Santa Cruz Radio Face
661 GM Adapter Harness 662 Antenna Adapter
Completed Santa Cruz RetroRadio™ Installation
1. To install the Santa Cruz RetroRadio™:
Before installing, disconnect the vehicle’s
negative battery terminal. First, access the
radio receiver box by removing the panel just
below the steering column. Remove the two
screws located at the bottom corners of the
panel, then remove the panel.
2. Locate the receiver box just above the gas
pedal. A mounting bracket located on the
bottom side, holds the receiver box in place.
Remove the three screws holding the receiver
box in place. Unplug the radio controller,
EQ/cassette unit and main harnesses.
Remove the antenna plug, and remove
the receiver box.
3. Next, the controller in the dashboard (located
to the upper right of the instrument panel)
must be removed. Remove the four screws
holding the trim bezel, and carefully remove it
from around the gauges. Carefully remove
the four screws holding the controller in place,
then remove the controller from the dash.
4. Route the Face to Body Cable connected to
the Santa Cruz Radio Face from the controller
location to the receiver box location through
the opening in the dash.
5. Next, you will be connecting the Santa Cruz
Radio Face to the RetroSound
®
radio body
(Motor). Plug in the Face to Body Cable by
connecting the ribbon cable to the front of
the radio body and the shaft plugs to the sides
of the radio body.
The factory radio in this vehicle is a two or three-part system consisting of: a radio controller
mounted in the upper-right side of the dash, an optional EQ or tape player located in the center of
the lower dash and the radio receiver box located under the dash just above the gas pedal area.
The 661 GM Adapter Harness and 662 Antenna Adapter are provided to connect Santa Cruz
to your vehicle’s factory wiring harness and antenna. Refer to the User’s Manual in your
Motor box for wiring instructions.
What’s in the Box Installation Instructions
MODERN SOUND FOR YOUR CLASSIC
While looking down at the radio body with the
cables coming out the back, the imprinted
“RetroSound” will be right-side up on the top of
the radio body chassis. The cable marked “R”
plugs into the input to the right of “RetroSound”
on the radio body, and the cable marked “L”
plugs into the left side.
6. Using the backstrap, mount your radio body
into the receiver box location above the
gas pedal.
7. Mount the Santa Cruz Radio Face into the
controller location. Reconnect your battery,
and test your system to make sure everything
works before continuing.
8. Finally if everything works, replace the trim
bezel and lower dash panel.
Face to Body Cable
www.retromanufacturing.com Phone: [phone]

BASIC OPERATING GUIDE
Refer to the Userʼs Manual in your Motor box for more comprehensive instructions.
Control Layout Basic Operation
MODERN SOUND FOR YOUR CLASSIC
#3
#1
#2
#8
#9
#4 #5 #6 #7
1. Top-Front Knob
2. Top-Rear Knob
3. Preset Button
4. Preset Button
5. Preset Button
6. Preset Button
7. Preset Button
8. Bottom-Front Knob
9. Bottom-Rear Knob
Radio Presets
Setting Radio Presets
Buttons #3 - #7 are your radio presets. To set
a preset, simply tune to the station you
want to set, then press and hold the preset
button (#3 - #7) for two seconds.
Recalling Radio Presets
To recall a preset, simply press the preset
button (#3 - #7).
Power On/Off
Press the Top-Front Knob (#1) to power the unit on.
Press and hold the Top-Front Knob (#1) to power the unit off.
Volume
Rotate the Top-Front Knob (#1) to change the volume.
Changing Source Modes
Rotate the Top-Rear Knob (#2) clockwise to cycle through the source modes.
Tune
Rotate the Bottom-Front Knob (#8) to scroll through the stations.
Mute On/Off
Press the Bottom-Front Knob (#8) to mute and unmute.
Equalizer (EQ)
Press the Top-Front Knob (#1) to enter the Tone Control sub-menu. Repeatedly press the
knob (#1) to click through the menu options until you see BASS, MIDDLE or TREBLE. To
change the EQ, navigate to the option you want to adjust, then rotate the Top-Front
Knob (#1). Press the knob (#1) to move onto the next menu item, and repeat to adjust.
Setting the Clock
Press and hold the Bottom-Front Knob (#8) to enter the System Settings sub-menu.
Rotate the knob (#8) to cycle through the choices. Highlight CLK, then press the knob
(#8) to select. Then rotate to adjust hours. Press the knob (#8) again to move onto
minutes. Rotate to adjust.
Display Color
Press and hold the Bottom-Front Knob (#8) to enter the System Settings sub-menu.
Rotate the knob (#8) to cycle through the choices. Highlight SCAN, then press the knob
(#8) to cycle through the colors.
Beep On/Off
Press and hold the Bottom-Front Knob (#8) to enter the System Settings sub-menu.
Rotate the knob (#8) to cycle through the choices. Highlight BEEP, then press the knob
(#8) to toggle the beep on or off.
www.retromanufacturing.com Phone: [phone]