REVELL KIT 1743 User manual

®
Á LIRE AVANT DE COMMENCER
• DÉGAGGEZ UN ESPACE POUR
TRAVAILLER.
• ÉTUDIEZ LES ÉTAPES DE MONTAGE
AVANT DE COMMENCER.
• CHAQUE PIÉCE EN PLASTIQUE PORTE
UN NUMÉRO DE PIÉCE.
• LISEZ LA RE MARQUE CONCERNANT
L´APPLICATION DES AUTO-COLLANTS,
´A L´ ÉTAPE 7.
MISE EN GARDE:
POSITIONNEZ AVEC PRÉCAUTION
TOUTES LES PIÉCES DE CE MODÉLE
RÉDUIT, CAR VOUS NE POUVEZLES
EMBOîTER QU’UNE SEULE FOIS.
If you have any questions or comments, call our hotline at: [phone]
or, please write to:
Revell Inc Consumer Service Department, 1840 Howard Street Unit A, Elk Grove Village, Illinois 60007
Be sure to include the plan number (85174310200), part number, description, your return address and phone number.
Visit our website: www.revell.com
HUEY CHOPPER
85174310200
READ BEFORE YOU BEGIN
• CLEAR A SPACE TO WORK ON
• STUDY THE ASSEMBLY DRAWINGS
BEFORE YOU BEGIN
• EACH PLASTIC PART IS IDENTIFIED BY
A PART NUMBER
• SEE NOTE ABOUT APPLYING
STICKERS IN STEP #7
CAUTION:
POSITION ALL PARTS IN THIS KIT
CAREFULLY. PARTS WILL ONLY SNAP
TOGETHER ONCE.
KIT 1743
* REPEAT SEVERAL TIMES
* A REPETER PLUSIEURS FOIS
* REMOVE AND THROW AWAY
* A RETIRER ET JETER
* APPLY STICKER
* APPLIQUEZ LES AUTO-COLLANTS
During the 1960’s, the
lack of effective close
air support aircraft led
to the creation of the
Bell UH-1B “Huey”
Gunship. Fitted with
various guns, these
armed helicoptors were
used quite success-
fully in Southwest Asia.
Your Revell model is
tted with two externally
mounted .50 caliber ma-
chinegunpodsand spin-
ning main and tail rotors.
Revell Inc Elk Grove Village, IL. Copyright © 2009. All rights reserved.

Step 1
Step 2
Step 3
A
9
SEATS
8
CONTROL
STICK
“T” SHAPED SLOT
HOLE
7
WALL
6
FLOORBOARD
10
SHAFT
PIN
HOLE
11
ROTOR
20
WINDOW TOP EDGE
1R
FUSELAGE
BOTTOM EDGE
HOLE
19
WINDOWS
PIN
B
1R
FUSELAGE
Place control
stick into “t”
slot and Push
forward into
Place
forward
first Place bottom edge of
windows into inside of fuse-
lage oPening then snaP toP
edge into the oPening
rePeat for left
side using Parts #1l,
fuselage, #26 window,
#27 windows
KIT 1743 Page - 1

Step 4
Step 6
Step 5
NOTCH NOTCH
1R
FUSELAGE
1L
FUSELAGE
3
STABILIZER
22
STABILIZER
5
SHAFT
SLOT
4
ROTOR
12
GUN POD
13
SUPPORT
12
GUN POD
2
SKID
firstsecond
KIT 1743 Page - 2

1
1 2
2
132
1 3 2
4
1
NOTE: When applying stickers, avoid touching the “sticky” side to prevent finger prints on stickers. Bend sticker sheet slightly
to lift edge of sticker & use a fingernail to lift sticker from sheet. Line up sticker on body and carefully press an edge
into place, slowly working sticker with a fingernail until sticker is fully on model.
REMARQUE : Pendant l’application des autocollants, éviter de toucher à la face collante pour ne pas laisser d’empreintes.
Plier légèrement la feuille d’autocollants pour relever le bord d’un autocollant, et le détacher de la feuille avec le
bout d’un ongle. Aligner l’autocollant sur la carrosserie, appuyer pour coller un de ses bords, et continuer de
l’appliquer lentement du bout de l’ongle jusqu’à ce qu’il soit complètement collé sur le modèle réduit.
Step 7 Sticker Placement Guide
KIT 1743 Page - 3