RH Baby&child BELLE STORAGE DESK User manual

PARTS INCLUDED
A [1] STORAGE DESK
TOOLS NEEDED
PHILLIPS-HEAD SCREWDRIVER (NOT INCLUDED)
1
2
3
4
Plastic Anchors
Metal Brackets
2 pcs.
2 pcs.
2 pcs.
2 pcs.
Cap Nut
Phillips Screws M4x30 mm
52 pcs.
Phillips Screws M4x19 mm
61 pc.
Metal Cable
NO. ITEM DESCRIPTION QT Y.
STEP 1: AT FINAL LOCATION, place the Desk (A)
down on a flat and smooth surface.
Remove all screws from the crossbars on bottom
of the Desk (A). DO NOT REMOVE CROSSBARS
UNTIL UNIT ARRIVES AT FINAL DESTINATION.
Phillips-head screwdriver
(not included)
page 1 of 3
BELLE STORAGE DESK INSTRUCTIONS
ASSEMBLY INSTRUCTIONS:
CARE INSTRUCTIONS:
1. DUST OFTEN USING A CLEAN, SOFT, DRY LINT-FREE CLOTH.
2. BLOT SPILLS IMMEDIATELY, AND WIPE WITH A CLEAN, DAMP CLOTH.
3. WE DO NOT RECOMMEND THE USE OF CHEMICAL CLEANSERS, ABRASIVES OR FURNITURE POLISH ON LACQUERED
FINISH.
A

STEP 2: Carefully return the desk to its upright
position.
page 2 of 3
1
YOUNG CHILDREN MAY BE INJURED BY TIPPING FURNITURE AND THE USE OF A TIPPING RESTRAINT IS HIGHLY
RECOMMENDED. WHEN PROPERLY INSTALLED, THIS RESTRAINT COULD PROVIDE PROTECTION AGAINST THE
UNEXPECTED TIPPING OF FURNITURE DUE TO SMALL TREMORS, BUMPS OR CLIMBING. WE RECOMMEND
MOUNTING THIS RESTRAINT TO A WALL STUD.
FURNITURE TIPPING RESTRAINT:
THIS PRODUCT IS ONLY A DETERRENT. IT IS NOT A
SUBSTITUTE FOR PROPER ADULT SUPERVISION.
1. ATTACH ONE OF THE METAL BRACKETS NEAR THE TOP
BACK EDGE OF THE FURNITURE PIECE BY INSERTING
THE SHORTER SCREWS.
2. DETERMINE THE FINAL POSITION OF THE FURNITURE
PIECE. MARK LOCATION ON THE WALL APPROXIMATELY 2"
BELOW THE BRACKET MOUNTED TO THE BACK OF THE
FURNITURE.
3. DRILL A STARTER HOLE INTO THE WALL STUD. IF WALL
STUD IS NOT AVAILABLE, DRILL A HOLE INTO THE
WALL AND INSERT PLASTIC ANCHOR. GENTLY TAP THE
ANCHOR UNTIL THE FLANGE OF THE ANCHOR IS FLUSH
WITH THE WALL.
4. ATTACH THE SECOND BRACKET BY INSERTING THE
LONGER SCREW THROUGH THE BRACKET AND INTO
THE WALL.
5. ATTACH ONE OF THE CAP NUTS TO ONE END OF THE
METAL CABLE AND SECURE HAND TIGHT. SLIDE THE
OPEN END OF THE METAL CABLE THOUGH THE HOLE
IN THE BRACKET LOCATED ON THE BACK OF THE
FURNITURE.
WARNING:
WALL
Wall
4
5
2
3
6
BELLE STORAGE DESK INSTRUCTIONS

6. PLACE THE FURNITURE SO THE BRACKET ON THE BACK
EDGE IS IN LINE WITH THE BRACKET IN THE WALL.
(NOTE: YOU MAY NEED TO MOVE THE BRACKET ON
FURNITURE TO THE LEFT OR RIGHT TO MAKE IT CLOSE
ENOUGH TO WALL STUD).
7. SLIDE THE OPEN END OF THE METAL CABLE THROUGH
THE BRACKET ON THE WALL AND SECURE HAND TIGHT
WITH A CAP NUT.
8. CHECK TO MAKE SURE THE METAL CABLE IS SECURELY
LACED AND LOCKED TO THE BRACKETS.
9. CAREFULLY POSITION THE FURNITURE AGAINST THE
WALL IN ITS FINAL POSITION.
10. THE ADJUSTABLE LEVELERS SHOULD BE USED WHEN
THE FURNITURE IS PLACED ON AN UNEVEN FLOOR.
Can be adjusted
by using Leveler.
page 3 of 3
BELLE STORAGE DESK INSTRUCTIONS