RHINO IM007 User manual

Arm
There are two methods to arm the immobiliser:
Automatic: The immobiliser will automatically arm itself 30 seconds after the vehicle ignition is turned
off. The blue LED # button light will slowly flash to indicate that the system is armed.
Manual: Turn off the vehicle ignition, then press and hold [#] on the keypad for 2 seconds until you
hear it beep twice. The blue LED # button light will slowly flash to indicate that the system is armed.
Disarm
To disarm the car immobiliser, ensure vehicle ignition is switched off. Now enter [*] [CODE] [#] on the
keypad. The keypad will beep twice if the code is correct. Now start the vehicle within 15 seconds of
entering the code. The blue LED will turn off while driving.
(Note: 1234 is the default factory code and must be changed by the owner). See “How to Change the
Disarm Code” below.
Incorrect Code: If an incorrect code is entered to disarm the vehicle, the keypad will beep four times. If
this happens, press [*] and re-enter the code correctly.
You can have 3 attempts in a row using an incorrect code. After the third attempt, the keypad will
become become unusable for one minute before you can try again.
How to Change Your Disarm Code
1. Disarm the immobiliser first. Now turn the vehicle ignition on.
2. Within 15 seconds of Step 1, enter [*] [#] [#] [CODE] [#] [#] [#] (The default code is 1234). The
keypad will beep twice,and the blue LED light will flash quickly, indicating that the code is ready to
be changed.
3. Now Press [*] and then enter your new four-digit code [?] [?] [?] [?] [#]. The keypad will beep
twice, indicating the new code has been saved. This is the only code that will now work. If you
forget it, the device needs to be returned to the manufacturer to be reset. DO NOT FORGET YOUR
NEW CODE!
Valet Parking / Car Servicing Mode
(Temporarily disables auto-arming for maximum 15minutes of driving at a time).
1. With the immobiliser disarmed and ignition turned on, enter [*] [#] [CODE] [#] [#] on the keypad. It
will beep three times and the blue LED light will stay turned on SOLID, indicating that the
immobiliser is currently in Valet Mode.
2. To manually exit Valet Mode, turn the ignition on and then press and hold [*] for 2 seconds. The
keypad will beep three times and the blue LED light will turn off, indicating that it has exited Valet
Mode.
3. Valet Mode will also turn itself off automatically after fifteen minutes of driving at one time. The
keypad will beep three times and the LED light will turn off, indicating that it has exited Valet Mode.
IM007 Keypad Car Immobiliser Instruction Manual
R
RhinoCo Technology
9 Hannabus Place
McGraths Hill NSW 2756 Australia
www.rhinoco.com.au
Tech Support Ph 02 9671 6711

Installation & Wiring Information
Note: This Immobiliser is for use on 12V DC vehicles only.
Wire Number
Connection
1
Connect to constant 12V power though a 5 Amp fuse.
2
Connect to ground.
3
Connect to a +12 volts ignition switched lead, which does not fall to 0 volts when the
engine is cranked.
6 & 7
8 & 9
Immobilisation Circuits. 30A Max.
The starter wire is usually located under the steering column of the vehicle. This wire
must be +12 Volts only when the vehicle is being started. Cut this wire. The vehicle
should not start. Solder the starter motor side to both wires marked 7. Solder the other
end to both wires marked 6.
Repeat the above configuration for the electric fuel pump with wires 9 & 8.
IMPORTANT! INSTALLER INFO
FIRST TIME POWER-UP ONLY
The very first time you connect power,
the system is "ARMED" but there will
be no light on the keypad for 60
seconds. Either wait for 60 seconds for
the [#] button to turn blue and start
flashing slowly OR
wake system up by pressing [*] [1234]
[#]
12 Month Warranty
RhinoCo Technology warrants its products to be in conformance with its own plans and specifications and to be
free from defects in materials and workmanship under normal use and service for 12 months after purchase.
For full warranty details visit www.rhinoco.com.au/legal/terms