Ribao BC-55 User manual

BC-55 User Manual V1.2
Contents
BC-55 User Manual V1.2...........................................................................................................1
1 Appearance and Key Panel...................................................................................................2
2 Choose Currency...................................................................................................................... 2
3 Working Modes..........................................................................................................................3
3.1 Mixed Denomination Counting(MDC).................................................................. 3
3.2 Single Denomination Counting(SDC).................................................................. 4
3.3 Counting mode (CNT)................................................................................................ 5
4 Batch............................................................................................................................................. 5
5 Accumulation Mode(ADD).................................................................................................... 6
5.1 Turn on the ADD function。.....................................................................................6
5.2 Turn off the ADD function........................................................................................ 7
6 Speed setting............................................................................................................................ 7
7 Print Function............................................................................................................................ 8
7.1 Print quantity and amount。...................................................................................8
7.2 Print serial number......................................................................................................8
8 Counting list............................................................................................................................... 9
8.1 Check the counting list ............................................................................................9
8.2 Check the serial number........................................................................................ 10
9 Set Menu................................................................................................................................ 11
9.1 Preferred Setting....................................................................................................... 12
9.1.1 Detection level................................................................................................12
9.1.2 Double Detection Sensitivity Setting.................................................... 13
9.1.3 Damage Detection Setting .................................................................... 13
9.1.4 Commonly Used Batch Qty ..................................................................... 13
9.1.5 Start Mode ..................................................................................................... 13
9.1.6 Background color selection ................................................................... 14
9.1.7 Main interface style .................................................................................... 14
9.1.8 Custom display window.............................................................................. 14
9.2 Basic Setting ............................................................................................................. 14
9.2.1 Date & Time Firmware and Software version Inquiry....................14
9.2.2 Buzzer function ............................................................................................ 15
9.2.3 RS232 serial port setting RS232 ........................................................15
9.2.4 Firmware and Software version Inquiry.............................................. 15
9.2.5 Language Setting.......................................................................................... 16
9.3 Restore to factory setting .................................................................................... 17
10 Error code sheet............................................................................................................... 17
10.1 System Error code................................................................................................. 18

1 Appearance and Key Panel
2Choose Currency
Press key or choose the country flag on touch
screen to choose the currency.

2.1 For single currency, touch the country flag to choose currency.
After finish choosing currency, it will enter into main interface; if you want to
cancel, please press to exit. means it is in active
mode, which is the currency mode before your change.
3Working Modes
Press key or touch the screen can change the working
modes.
3.1 Mixed Denomination Counting(MDC)
In this mode, all the denominations can be recognized and counted, calculating
the quantity and amount at the same time. Serial number can also be recorded
if you turn on the serial number reading function. You can check the serial
number details under another interface.
Under mult-currency counting mode, the display will show the total amount and
total quantity for each currency.

3.2 Single Denomination Counting(SDC)
This mode is mainly for counting the same denomination notes, for example,
to count the same denomination already sorted. The machine will stop when
it recognize a different denomination, you need to remove this note and
continue counting. The machine recognize the first note and count following
notes based on this standard, thus, when version sorting is turned on, it will
stop when it recognize a different version.
Under this mode, the machine can also calculate amount and quantity, as
well as serial number reading.

3.3 Counting mode (CNT)
In this mode, it will not calculate the amount, only calculate quantity. When
ADD function is not turned on, it will only display the current counting
quantity; when ADD is turned on, it will display the current counting quantity
and accumulated counting quantity.
NOTE: under MDC&SDC mode, the machine checks the notes by image, MG,
UV and DB(double notes detection), under CNT mode only has DB detection.
4 Batch
Press touch button or press key can change the
batch quantity, there are some default batch quantity set in system. If you
want to define the batch number yourself, please go to SET menu and set
yourself.
When batch function is turned on, the current batch quantity will display in
the red frame position. The machine will stop when batch quantity is
achieved and prompt a message on display.After remove the notes, it will
start from 0 again if ADD is not turned on, otherwise it will accumulate.

5Accumulation Mode(ADD)
Press key or touch the screen mark to open or close
ADD function.
5.1 Turn on the ADD function。
When ADD function is on: The amount and quantity will not be cleared unless
you press clear key. Details as below:
4.1.1 After finish counting a bundle of notes and the notes are not removed,
the machine displays the amount and quantity of this bundle of notes; if the
notes are removed, the latest counting data will be accumulated to historical
data and the machine will display the accumulated total data.Press CLR key
it will clear the latest counting data, press CLR two times it will clear the total
data.
4.1.2 During the counting, if some abnormal situation happens such as jam,
the machine will delete the current counting data.
4.1.3 In ADD mode,when you check the serial number details, the machine
will only show the serial number of latest 200 notes.
If the ADD function is turn on, you can see the mark as below.

5.2 Turn off the ADD function.
If you start to count a new bundle of notes, it will start from 0. Details as below
4.2.1 After finish counting a bundle of notes, no matter the notes are
removed or not, the machine only displays the current counting data, press
CLR key it will clear all the data.
4.2.2 During the counting, if some abnormal situation happens such as jam,
the machine will delete the current counting data.
4.2.3 When you check the serial number details, the machine will only show
the serial number of latest 200 notes.
6 Speed setting.
Press key or click key to adjust the speed. Shown as
picture.
Speed
Counting Mode (Function)
1500pc/min
CNT：Quantity
1200pc/min
CNT : Quantity
MDC : Quantity & Amount
SDC : Quantity & Amount
1000pc/min
CNT : Quantity
MDC : Quantity, Amount &Serial number reading
SDC : Quantity, Amount &Serial number reading
800pc/min
CNT : Quantity
MDC : Quantity , Amount , Serial number reading,
Mix-currency counting & Auto recognition
SDC : Quantity , Amount , Serial number reading,
Mix-currency counting & Auto recognition

7 Print Function
Thermal printer is recommended to connect with machine through RS232 port.
You can set the baud rate under SET mode, the default baud rate is 115200.
7.1 Print quantity and amount。
Under List interface, press key or click and the printing
receipt is shown as below
7.2 Print serial number
Under serial number list, press key or touch the receipt is
shown as below

8 Counting list
8.1 Check the counting list
Press one time to display the quantity and amount

8.1.1 When the ADD function is off, only show the current counting result.
Check next page if have multi currencies.
8.1.2 When ADD is on, if the notes are not removed, it will show current
amount and quantity; after remove the notes, it will accumulate the latest
bundle of notes data to previous data. Press PRINT key to print the list.
8.2 Check the serial number
Press key twice to check the serial number
The serial number is available to check when speed is set at 800-1000pcs/min,
and you can only check the serial number of latest 200pcs notes. Press PRINT
key or touch the Print key on LCD to print