Rice Lake 882IS User manual

882IS and 882IS Plus
Intrinsically Safe Indicator/Controller
Version 1
Technical Manual
PN 183532 Rev GApril 2, 2021

An ISO 9001 registered company
© Rice Lake Weighing Systems. All rights reserved.
Rice Lake Weighing Systems® is a registered trademark of
Rice Lake Weighing Systems.
All other brand or product names within this publication are trademarks or
registered trademarks of their respective companies.
All information contained within this publication is, to the best of our knowledge, complete and
accurate at the time of publication. Rice Lake Weighing Systems reserves the right to make
changes to the technology, features, specifications and design of the equipment without notice.
The most current version of this publication, software, firmware and all other product
updates can be found on our website:
www.ricelake.com

Contents
© Rice Lake Weighing Systems ● All Rights Reserved i
Contents
Technical training seminars are available through Rice Lake Weighing Systems.
Course descriptions and dates can be viewed at www.ricelake.com/training
or obtained by calling 715-234-9171 and asking for the training department.
1.0 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.1 Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.2 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1.3 FCC Compliance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1.4 FM Approval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.5 Hazardous Location Labels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.6 Operating Modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.7 Front Panel Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.8 General Navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.8.1 Edit Parameter Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.8.2 Alphanumeric Entry Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.9 Indicator Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.9.1 Toggle Gross/Net Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.9.2 Toggle Units. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.9.3 Zero Scale . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.9.4 Acquire Tare. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.9.5 Remove Tare Value . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1.9.6 Preset Tare (Keyed Tare) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1.9.7 Print Ticket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1.9.8 Front Panel User Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1.9.9 Displaying Audit Trail Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1.9.10 Display Accumulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.9.11 Clear the Accumulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.9.12 Display Tare. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.0 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.1 Unpacking and Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.2 Product Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.3 Hazardous Area Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.4 Mounting Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.4.1 Backplate Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.5 Cable Connections on the 882IS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.5.1 Power Supply to Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.5.2 AC Power Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.5.3 Battery Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.5.4 Load Cells . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.5.5 Cable Shield Grounding. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.5.6 882IS Enclosure Grounding. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.5.7 CPU Board Replacement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.5.8 Serial Communications – Port 1 (COM). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.6 CPU Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.7 Audit Trail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2.8 Digital Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2.9 Backplate Attachment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2.10 Legal for Trade Sealing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2.11 IO Module Option Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2.12 Rechargeable Battery Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2.13 Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

882IS/882IS Plus
ii Visit our website www.RiceLake.com
Rice Lake continually offers web-based video training on a growing selection
of product-related topics at no cost. Visit www.ricelake.com/webinars
3.0 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3.1 Configuration Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3.2 User Setup Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.2.1 Audit Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.2.2 User ID. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.2.3 Setup Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
3.2.4 Scale Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
3.2.5 Scale Format Menu - if Split = Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
3.2.6 Scale Format Menu - if split = 2 RNG, 3 RNG, 2 INTVL, 3 INTVL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
3.2.7 Calibration Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
3.2.8 Features Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
3.2.9 Region Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
3.2.10 Region - Regulation - Indust . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
3.2.11 Keylock Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
3.2.12 Setup Ports Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
3.2.13 Ports - Serial Ports Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
3.2.14 Ports - Fiber Optics Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
3.2.15 Print Format Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
3.2.16 Digital Inputs Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
3.2.17 IO Module Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
3.2.18 Power Savings Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
3.2.19 Version Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
3.3 Test Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
3.4 Time and Date. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
3.5 Accumulator Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
3.6 Tare. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
4.0 Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
4.1 Front Panel Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
4.1.1 Five-Point Linearization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
4.1.2 Rezero . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
4.2 Last Zero. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
4.3 Temporary Zero . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
4.4 Adjusting Final Calibration (Trimming) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
4.5 Gravity Compensation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
4.6 EDP Command Calibration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
4.7 Revolution® Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
5.0 Using Revolution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
5.1 Communication With the Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
5.2 Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
5.2.1 New Configuration File. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
5.2.2 Open an Existing Configuration File. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
5.2.3 Saving a Configuration File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
5.3 Revolution Help. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
6.0 EDP Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
6.1 The EDP Command Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
6.1.1 Key Press Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
6.1.2 Reporting Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
6.1.3 The RESETCONFIGURATION Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
6.1.4 Parameter Setting Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Contents
© Rice Lake Weighing Systems ● All Rights Reserved iii
Contents
Technical training seminars are available through Rice Lake Weighing Systems.
Course descriptions and dates can be viewed at www.ricelake.com/training
or obtained by calling 715-234-9171 and asking for the training department.
6.1.5 Scales Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
6.1.6 Format Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
6.1.7 Calibration Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
6.1.8 Ports COM Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
6.1.9 Stream Tokens Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
6.1.10 Feature Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
6.1.11 Regulatory Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
6.1.12 Passwords Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
6.1.13 Keypad Lock Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
6.1.14 Print Format Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
6.1.15 Digital I/O Configuration Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
6.1.16 Weigh Mode Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
6.1.17 Power Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
6.1.18 Setup Mode Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
6.1.19 Analog Output Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
6.1.20 Analog Output Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
6.1.21 Test Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
7.0 Print Formatting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
7.1 Print Formatting Tokens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
7.2 Default Print Formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
7.3 Customizing Print Formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
7.3.1 Using the EDP Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
7.3.2 Using the Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
7.3.3 Using Revolution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
8.0 Setpoints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
8.1 Hardware Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
8.2 Software Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
8.3 Connect the Fiber-Optic Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
8.4 920i iRite Software Setup Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
8.5 920i Setup Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
8.6 882IS/882IS Plus Setup Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
8.7 Setpoint Configuration Procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
8.8 Setpoint Batching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
8.9 920i Batch Operations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
9.0 IO Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
9.1 IO Module Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
9.1.1 AC Wiring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
9.1.2 RS-232/RS-422 Communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
9.2 USB Device Communications – Port 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
9.3 Ethernet Communications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
9.4 Updating IO Module Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
10.0 Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
10.1 Error Messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
10.1.1 Displayed Error Messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
10.2 Using the HARDWARE Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
10.3 ERROR Commands Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

882IS/882IS Plus
iv Visit our website www.RiceLake.com
Rice Lake continually offers web-based video training on a growing selection
of product-related topics at no cost. Visit www.ricelake.com/webinars
10.4 Status Messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
10.5 TARE and ZERO Key Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
10.6 Data Formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
10.6.1 Stream Serial Data Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
10.6.2 Print Output Serial Data Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
10.7 Custom Stream Formatting – Input/Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
10.8 Stream Formatting Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
10.8.1 Toledo 8142 Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
10.8.2 Cardinal 738 Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
10.8.3 Weightronix WI 120 Indicator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
10.9 ASCII Character Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
10.10 Digital Filtering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
10.10.1 Sample Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
10.10.2 Digital Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
10.11 Updating the 882IS/882IS Plus CPU Firmware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
10.12 Analog Output Calibration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
11.0 Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
12.0 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

Introduction
© Rice Lake Weighing Systems ● All Rights Reserved 1
1.0 Introduction
This manual provides information on installation, configuration, calibration and servicing of the 882IS and 882IS Plus indicator.
The installer should be familiar with requirements for installation of equipment in hazardous areas. Refer to the 882IS/882IS
Plus Conditions of Use document (PN 191698) for the intrinsic safety certification and classification, specific conditions of use
and system limitations and restrictions for the 882IS/882IS Plus.
Configuration and calibration of the indicator can be accomplished using the indicator front panel keys, the EDP command set
or Revolution® configuration utility. See Section 3.0 on page 21 for information about configuration methods.
Manuals and additional resources are available from the Rice Lake Weighing Systems website at www.ricelake.com
Warranty information can be found on the website at www.ricelake.com/warranties
1.1 Options
Options and accessories are listed below.
Part No. Description
180831 Battery option, IS6V2
194191 Battery charger, IS6V2, 100-240 VAC NEMA 5-15 (NA plug)
194189 Battery charger, IS6V2, 100-240 VAC (EU plug)
194192 Battery charger, IS6V2, 100-240 VAC (UK plug)
197591 Battery charger, IS6V2, 100-240 VAC (Australian Plug)
180837 Power supply, 882IS mb-EPS-100-240-X2, dual output 6.8
VDC 200 mA
195109 Power supply, 882IS mb-EPS-100-240-X2, dual output 6.8
VDC 200 mA, 1/2'' NPT-M20
179668 Cable, M12 power 22'' hazardous location (for battery version)
179669 Cable, M12 power 10' hazardous location
179670 Cable, M12 power 50' hazardous location
179671 Cable, M12 power 100' hazardous location
190979 Lockout device for M12 device
163751 Tilt stand, 882IS
179678 Tilt stand, 882IS battery option
177850 Panel mount option, gasketed non-NEMA seal
Table 1-1. Options and Accessories
Part No. Description
177709 Module, 882 Smart I/O interface
196166 Module, 882 Smart I/O (EU power cord)
196165 Module, 882 Smart I/O (UK power cord)
196769 Option, Fiber/RS232 6x6 FRP Enclosure, Fiber Optic-232
converter, External Power Supply
196770 Option, Fiber/RS422 6x6 FRP Enclosure, Fiber-RS422
converter, External Power Supply
78026 Cable, Plastic Optical 100' includes polishing kit
78027 Cable, Plastic Optical 200' includes polishing kit
197384 Kit, polishing POF cable
Option Cards
190528 Single analog output (0-10VDC, 0-20mA, 4-20mA)
190530 882 option, Ethernet/IP
190531 882 option, DeviceNet
190532 882 option, ProfiNet
190534 882 option, Profibus
190533 882 option, Modbus TCP
Remote Indicator for Setpoint Functionality
203343 920i universal indicator, 115 VAC, no A/D, with 882IS iRite
software for setpoints
203344 920i wall mount indicator, 115 VAC, no A/D, with 882IS iRtie
software for setpoints
Table 1-2. Optional I/O Module

882IS/882IS Plus
2 Visit our website www.RiceLake.com
1.2 Safety
Safety Signal Definitions:
Indicates an imminently hazardous situation that, if not avoided, will result in death or serious injury. Includes
hazards that are exposed when guards are removed.
Indicates a potentially hazardous situation that, if not avoided, could result in serious injury or death. Includes
hazards that are exposed when guards are removed.
Indicates a potentially hazardous situation that, if not avoided, could result in minor or moderate injury.
Indicates information about procedures that, if not observed, could result in damage to equipment or corruption
to and loss of data.
General Safety
Do not operate or work on this equipment unless this manual has been read and all instructions are understood.
Failure to follow the instructions or heed the warnings could result in injury or death. Contact any Rice Lake
Weighing Systems dealer for replacement manuals.
Failure to heed could result in serious injury or death.
Some procedures described in this manual require work inside the indicator enclosure. These procedures are to be performed by
qualified service personnel only.
Do not allow minors (children) or inexperienced persons to operate this unit.
Do not operate without the enclosure completely assembled.
Do not use for purposes other than weight taking.
Do not place fingers into slots or possible pinch points.
Do not use this product if any of the components are cracked.
Do not exceed the rated specification of the unit (Section 12.0 on page 81).
Do not make alterations or modifications to the unit.
Do not remove or obscure warning labels.
Do not submerge.
1.3 FCC Compliance
United States
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
Canada
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio
Interference Regulations of the Canadian Department of Communications.
Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites applicables aux appareils
numériques de la Class A prescites dans le Règlement sur le brouillage radioélectrique edicté par le ministère des
Communications du Canada.
DANGER
WARNING
CAUTION
IMPORTANT
WARNING

Introduction
© Rice Lake Weighing Systems ● All Rights Reserved 3
1.4 FM Approval
The 882IS/882IS Plus is a FM Entity approved for:
• Classes I, II and III
• Division 1
• Groups A, B, C, D, E, F and G
• Class I, Zone 0, AEx/EX ia IIC
• Zone 0/20
• Zone 20 AEx ia IIIC
• IP66
• T-rating T4 = 14–104°F (-10–40°C)
Only devices that have FM Entity Approval with proper entity parameters may be used unless specifically listed in this manual
or control drawings (PN 77412, PN 180848 and PN 182301) as part of the Rice Lake Weighing Systems FM systems approval.
Failure to comply with this voids the FM approval.
This classification of hazardous materials are different in the US and European standards, because of this, the safety class of
the 882IS/882IS Plus is declared in the US standards: Class I, II, III, DIV1 and Groups A-G.
Substitution of components may impair intrinsic safety.
To prevent ignition of flammable or combustible atmospheres, disconnect power before servicing.
Disconnect all power to this unit before installing, servicing or cleaning. Failure to do so could result in bodily harm and/or
property damage.
The 882IS/882IS Plus has been certified by UL (U.S., Canada, ATEX and IECEx) with a temperature rating of 14–104°F
(-10–40°C) for use in hazardous environments where auto ignition temperature of the hazardous material is below the rating.
Do not install, disconnect or perform any service on this equipment before power has been switched off or the area has been
secured as non-hazardous by personnel authorized to do so by the responsible person on-site.
1.5 Hazardous Location Labels
The following labels will be affixed to the 882IS/882IS Plus.
Figure 1-1. 882IS/882IS Plus Indicator Label
Figure 1-2. IS6V2 Battery Label
Figure 1-3. mb-EPS-100-240-X2 Power Supply Label

882IS/882IS Plus
4 Visit our website www.RiceLake.com
1.6 Operating Modes
The three modes of operation for the 882IS/882IS Plus are described below.
Weigh Mode
In this mode, the indicator displays gross or net weights to indicate the type of weight value displayed, and annunciators to
indicate scale status.
Setup Mode
Most of the procedures described in this manual, including setup and calibration, require the indicator to be in Setup mode.
To enter setup mode, remove the fillister head screw from the bottom of the enclosure. Insert a non-conductive tool into the
access hole and press the setup switch once. the indicator display changes to show the word Scale.
Breaking the seal to enter the Configuration mode will void a Legal for Trade unit.
The 882IS/882IS Plus also has an Audit Trail that can track changes to setup and calibration, allowing the setup switch to be
bypassed with Jumper JP4 on the CPU board. If Audit Trail is enabled, setup mode can then be accessed through the User
Setup mode.
User Setup Mode
User Setup mode (accessed by pressing the ) is used to:
• View the audit trail, set time & date
• View or clear the accumulator value
• View the current tare value
• Enter Setup/Configuration mode (if audit trail is enabled)
IMPORTANT
MENU

Introduction
© Rice Lake Weighing Systems ● All Rights Reserved 5
1.7 Front Panel Display
Figure 1-5 shows the iRev 4 front panel display and Table 1-3 describes the key functions.
The numeric or weight portion of the display consists of the seven-segmented LCD digits and below that, is a messaging area
of the display which is the dot matrix and can display two-line non-configurable messages (ie: error messages).
The symbols on the keys in Figure 1-4 and Figure 1-5 (representing up, down, enter, left, right) describe the key functions when
in Configuration/Setup mode. The keys are used to navigate through menus, select digits within numeric values, and
increment/decrement values. See Section 3.2 on page 22 for information about using front panel keys in Configuration mode.
Key Function
The Zero key sets the current gross weight to zero;
Also used as the up key to navigate menus
The Print key sends an on-demand print format out a communications port, provided the conditions for standstill are met; If enabled in
configuration, Print may display while the unit prints;
Also used as the right key to navigate menus or to select another digit when editing a value
The Gross/Net key toggles the weight display between Gross and Net mode; If a tare value has been entered or acquired, the net
value is the gross weight minus the tare; Gross mode is shown by the Gross/Brutto annunciator; Net mode is shown by the net
annunciator;
Also used as the down key to navigate menus
The Menu key allows access the User Setup menu; This key also acts as the cancel key when editing parameter values, or as an exit
key when in the Configuration or User Setup menus
The Units key switches the weight display to an alternate unit, defined in the format menu (Figure 3-7 on page 25); Units Available: lb,
kg, oz, metric ton, ton, gram; Also used to navigate to different menus or to toggle to another digit when editing a value
The Tare key performs one of several predetermined Tare functions dependent on the mode of operation selected in the Tare Function
parameter; This key also acts as the Enter key for numeric or parameter entry
The Power key turns the unit on or off; Press and hold to turn on, press momentarily to turn off
Future enhancement
Table 1-3. 882IS/882IS Plus Key Functions
PTTHOLDPEAK PC SAMPLE %
882IS
ZERO
TARE
UNITS
GROSS
NET
B/N
MENU
PRINT
POWER
F1
START
F3
F4
F2
STOP
882IS
PTTHOLDPEAK PC SAMPLE %
ZERO
TARE
UNITS
GROSS
NET
B/N
MENU
PRINT
POWER
F1
START
F3
F4
F2
STOP
Figure 1-4. 882IS Front Panel Display Figure 1-5. 882IS Plus Front Panel Display
ZERO
PRINT
GROSS
NET
B/N
MENU
TARE
POWER
F1
START

882IS/882IS Plus
6 Visit our website www.RiceLake.com
1.8 General Navigation
The front panel keys are used to navigate through the menus in Configuration mode (Section 3.0 on page 21).
• and move left and right (horizontally) in a menu level
• and move up and down (vertically) to different menu levels
• serves as the Enter key for selecting parameter values within the menus
Press or to scroll left or right until the desired menu group appears on the display. Press to move
down to the sub-menu or parameter to be edited. When moving through the menu parameters, the current selected value
appears first on the display.
Future enhancement
Future enhancement
Future enhancement
The Clear key clears the current value during a numeric entry (available in the 882IS Plus)
The Decimal Point key inserts a decimal point where necessary (available in the 882IS Plus)
The numeric keypad can be used to enter values (available in the 882IS Plus)
Annunciator Function
Gross/Brutto Gross or Brutto weight mode
Net Net weight mode
Center of Zero - Indicates that the current gross weight reading is within ± 0.25 display divisions of the acquired zero, or is within the
center of zero band; A display division is a resolution of the displayed weight value, or the smallest incremental increase or decrease that
can be displayed or printed
Standstill - The scale is at a standstill or within the specified motion band; Some operations including zero, tare and printing can only be
done when the standstill LCD is on
Peak Hold Future enhancement
T Indicates that a tare has been acquired and stored by the system
PT Indicates that a preset tare weight has been keyed in or entered via the EDP command
PC Future enhancement
Sample Future enhancement
% Future enhancement
Table 1-4. Annunciator Functions
Key Function
Table 1-3. 882IS/882IS Plus Key Functions (Continued)
F2
STOP
F3
F4
0
PRINT
ZERO
GROSS
NET
B/N
TARE
PRINT
GROSS
NET
B/N

Introduction
© Rice Lake Weighing Systems ● All Rights Reserved 7
1.8.1 Edit Parameter Values
To change a parameter value, scroll left or right to view the values for that parameter. When the desired value appears on the
display, press to select the value and move back up one level. To edit numerical values, use the navigation keys to
select the digit and to increment or decrement the value. Alternatively, use the numeric keypad (882IS Plus), to enter the digits.
The decimal point will begin flashing if a decimal value is allowed. Use the navigation keys, to move the decimal point left or
right. Press when done.
1.8.2 Alphanumeric Entry Procedure
Use the following navigation path for alphanumeric entry when using the five button keypad.
Figure 1-6. Editing Procedure for Numeric Values
1.9 Indicator Operations
Basic 882IS/882IS Plus operations are summarized below.
1.9.1 Toggle Gross/Net Mode
Press to toggle the display mode between gross and net.
Net mode is available when a tare value has been entered or acquired (Net = Gross minus Tare). If a tare has not been
entered or acquired, the display remains in Gross mode. The B (Brutto), G (Gross) or NET icons on the LCD indicate
the current mode.
1.9.2 Toggle Units
Press to switch between primary and secondary units. The current units are displayed on the LCD.
1.9.3 Zero Scale
1. In Gross mode, remove all weight from the scale and wait for to display.
2. Press . displays and indicates the scale is zeroed.
The scale must be stable and within the configured zero range for the scale to be zeroed. If the scale cannot be
zeroed, No zero will display.
1.9.4 Acquire Tare
1. Place a container on the scale and wait for to display.
2. Press to acquire the tare weight of the container. The Net weight displays and the T annunciator displays to
show the tare value is entered.
TARE
TARE
Display rst 20
characters of format
Display and edit
active character and
ASCII value
Delete active
character
Scroll right in format string.
Scroll left in format string.
Increment ASCII value of active character
Decrement ASCII value
of active character.
Press to insert a space
before the active character.
Press to accept the changes
and return to the level above.
Press to accept the changes
and return to the level above.
GROSS
NET
B/N
Note
ZERO
0
Note
TARE

882IS/882IS Plus
8 Visit our website www.RiceLake.com
1.9.5 Remove Tare Value
1. Remove all weight from the scale and wait for . The display reads .
2. Press to zero the scale if needed.
3. Press (or in OIML mode). The display shifts to gross weight and the Gross icon is lit.
4. To clear the tare, press again.
1.9.6 Preset Tare (Keyed Tare)
If keyed tares are allowed, press to open the keyed tare prompt.
Tare mode must be set to keyed or both for the preset tare feature to function.
1. With scale empty and zero weight displayed, press . One flashing 0 displays with the focused digit flashing.
2. Key in the value using the keypad on the 882IS Plus (Section 1.9 on page 7).
• Press or to select the digit
• Press or to increment or decrement the value
• Press to move to the decimal point entry
• Press or to adjust the decimal point placement
• Press when the value is correct
The display will change to the Net mode and PT lights to show the preset tare was entered.
Entering a keyed tare of zero will remove the stored tare value.
1.9.7 Print Ticket
1. Wait for to light.
2. Press to send data to the configured communications port.
1.9.8 Front Panel User Setup
Press to enter User Setup mode. Use User Setup mode to:
• View audit trail information
• Enter Configuration mode if audit trail is enabled
• View or clear the accumulator
• View the current tare value
• Time and date
• Test menu
1.9.9 Displaying Audit Trail Information
The Audit Trail Configuration and Calibration counters can be viewed in User Setup mode.
1. Press . Audit displays.
2. Press to display the Legally Relevant Firmware version.
3. Press to display Calibration.
0
ZERO
TARE
ZERO
TARE
Note
TARE
TARE
PRINT
ZERO
GROSS
NET
B/N
TARE
PRINT
TARE
Note
PRINT
MENU
MENU
GROSS
NET
B/N
PRINT

Introduction
© Rice Lake Weighing Systems ● All Rights Reserved 9
4. Press to view the Calibration Counter.
5. Press to return to Calibration.
6. Press to display Configuration.
7. Press to view the Configuration Counter.
8. Press to return to Configuration.
9. Press to return to the Weigh mode.
1.9.10 Display Accumulator
Enable the accumulator before use in Weigh mode. Once enabled, weight (net weight if a tare is in the system) is accumulated
whenever a print operation is performed using the Print key, digital input, or KPRINT EDP command. The scale must return to
below the threshold value before the next accumulation.
1. Press to enter the User Setup mode, Audit displays.
2. Press or until Accumulator displays.
Accumulator is only displayed if the accumulator is enabled (Section 3.2.4 on page 23). The Print operation only
performs one accumulation, and only if the weight is above the accumulator threshold. Weight must return to below
the accumulator threshold value before another accumulation is allowed.
The EDP command SC.THRESH#n is configured in the setup menu (Section 3.2.4 on page 23).
3. Press . View displays.
4. Press to view the current accumulator value.
5. While the accumulator value displays, press to print the value.
6. Press to return to the Weigh mode.
1.9.11 Clear the Accumulator
1. Press to enter the User Setup mode. Audit displays.
2. Press or until Accumulator displays.
3. Press , then press or until Clear Accumulator displays.
4. Press to clear the accumulator. Clear will display briefly and display returns to Clear Accumulator.
5. Press to return to the Weigh mode.
1.9.12 Display Tare
When a tare value displays, the Gross and Net icons will be off and is lit. To display a tare:
1. Press .
2. Press to Tare and press to view the current tare value.
3. Press twice to return to Weigh mode.
If there is not a tare in the system, the value displayed is zero and the Gross and Net icons are turned off.
GROSS
NET
B/N
MENU
PRINT
GROSS
NET
B/N
MENU
MENU
MENU
PRINT
Note
GROSS
NET
B/N
GROSS
NET
B/N
PRINT
MENU
MENU
PRINT
GROSS
NET
B/N
GROSS
NET
B/N
TARE
MENU
0
MENU
PRINT
GROSS
NET
B/N
MENU
Note

882IS/882IS Plus
10 Visit our website www.RiceLake.com
2.0 Installation
This section describes procedures for connecting power, load cells, digital inputs and data communications cables to the 882IS
and 882IS Plus indicator.
* Use anti-static protection for grounding and to protect components from electrostatic discharge (ESD) when
working inside the indicator enclosure.
* Procedures requiring work inside the indicator must be performed by qualified service personnel only.
* Disconnect the indicator from power source before opening enclosure.
* Component level repair, excluding board-swapping, is not permitted on FM Approved equipment by anyone other
than the manufacturer. It is mandatory to return unit to Rice Lake Weighing Systems for repairs.
* The entire indicator must be shipped back to Rice Lake Weighing Systems for repair. Please contact a local dealer or
Rice Lake Weighing Systems to obtain a return material authorization (RMA). There are no user serviceable parts
within the unit except CPU board replacement. All repairs are to be performed by qualified service personnel only.
2.1 Unpacking and Assembly
Immediately after unpacking, visually inspect the unit to ensure all components are included and undamaged.
The shipping carton should contain the indicator and manual. If any parts were damaged in shipment, notify Rice Lake
Weighing Systems and the shipper immediately.
2.2 Product Dimensions
Figure 2-1. Product Dimensions (Universal and Optional Battery Versions Shown)
WARNING
IMPORTANT
B
C
DEFH
I
J
K
L
ABC
D
E
G
F

Installation
© Rice Lake Weighing Systems ● All Rights Reserved 11
Table 2-1. Product Dimensions
2.3 Hazardous Area Installation
The following information is provided to help the installer with the correct installation of the 882IS/882IS Plus system.
See the following diagram of a typical intrinsically safe system.
Figure 2-2. Intrinsically Safe System Diagram Example
Dimensions Without Battery
A 8.94'' (227.1 mm)
B 7.66'' (194.6 mm)
C 6.50'' (165.1 mm)
D 8.10'' (205.7 mm)
E 9.96'' (253 mm)
F 4.36'' (110.7 mm)
G 8.37'' (212.6 mm)
Dimensions with Optional Battery and Tilt Stand
H 4.64'' (117.9 mm)
I 5.00'' (127 mm)
J 9.03'' (229.4 mm)
K 10.29'' (261.4 mm)
L 13.06'' (331.7 mm)

882IS/882IS Plus
12 Visit our website www.RiceLake.com
2.4 Mounting Instructions
The 882IS/882IS Plus includes a universal mount. The universal mount can be mounted on a wall, tabletop or any flat surface.
The universal mount comes attached to the unit. Rice Lake Weighing Systems recommends removing the
882IS/882IS Plus from the universal mount prior to mounting.
Figure 2-3. Mounting the 882IS/882IS Plus
1. Using the mount as a template, mark the screw locations.
2. Drill holes for the screws.
3. Secure the universal mount using the appropriate length 1/4'' or M6 hardware (not included).
4. Reattach the 882IS to the universal mount.
2.4.1 Backplate Removal
Remove the backplate of the universal mount assembly to gain access to the inside of the enclosure and CPU board.
Figure 2-4. Remove Enclosure Backplate
1. Remove the nuts that attach the backplate to the enclosure.
The unit ships with Backplate Nut (4) installed.
2. Remove the backplate.
Disconnect power to the indicator prior to removing the backplate.
Note
Backplate
Backplate Nuts (8)
Note
WARNING

Installation
© Rice Lake Weighing Systems ● All Rights Reserved 13
2.5 Cable Connections on the 882IS
The 882IS has four cord grips at the bottom of the enclosure for cabling into the enclosure. One stainless steel cord grip is used
for the power supply and other cord grips are for the load cell cable, communications and the fiber optic cable. Two of the four
cord grips come with a plug installed to prevent moisture from entering the enclosure. Depending on the application, remove
the plug from the cord grip that will be used and install cables as required. Figure 2-5 shows the recommended 882IS cord grip
assignments.
Figure 2-5. Recommended Cord Grip Assignments
2.5.1 Power Supply to Indicator
Do not under any circumstances, connect or disconnect the DC wire from the indicator while the AC power is
applied to the power supply. This will cause the power supply fuse to blow.
The 882IS/882IS Plus must be powered by an FM-approved Rice Lake power supply or optional battery.
The power requirements of the 882IS indicator are as follows:
• Minimum input voltage – 5.8 VDC
• Maximum input voltage – 7.9 VDC
• Peak current consumption – .25 W
• Average input current (with four load cells) – 100-175 mA
The DC power cable should be attached to connector J4 (Figure 2-9 on page 16).
2.5.2 AC Power Wiring
Units are powered by an FM-approved power supply. 100-240 VAC into Rice Lake Weighing Systems mb-EPS-100-240-X2
intrinsically safe power supply is recommended. See the mb-EPS-100-240-X2 Power Supply Instruction sheet (PN 194894) for
information on wiring and power specifications.
Setup switch access screw
To power supply
Load cell cable cord grip
Communications cable cord grip
Fiber optic cord grip
WARNING
Note

882IS/882IS Plus
14 Visit our website www.RiceLake.com
2.5.3 Battery Option
The optional IS6V2 battery (PN 180831) provides an intrinsically safe battery that can replace the power supply. The battery is
approved for use in hazardous environments. A low battery error message displays on the 882IS to indicate that the battery
needs to be recharged. A fully charged battery is one that has been charged for a minimum of 12 hours. The battery charger
pilot lamp switches from amber color to off when the unit is approximately 40% charged. At that time, the charger switches over
to a float charge mode.
To keep the battery at full capacity, it is recommended to leave the battery connected to the charger, in float charge
mode, until ready to use. The battery can remain on the charger in float charge mode indefinitely without damaging
the battery. See 882IS IS6VS Battery Instructions (PN 194893) for instructions on charging the battery.
While connected to the DC battery pack with the indicator off, the 882IS still draws a small amount of current that will
shorten battery run time. To preserve battery life, disconnect the battery when not in use.
2.5.4 Load Cells
To attach a cable from a load cell or junction box, route the cable to the J1 connector. Wire the load cell cable from the load cell
or junction box to connector J1 as shown in Table 2-3. If using 6-wire load cell cable (with sense wires), open the unit (see
Section 2.4.1 on page 12) and remove jumpers JP1 and JP2.
For 4-wire installation, leave jumpers JP1 and JP2 on (Figure 2-10 on page 17).
Ensure Pins 3 and 4 are left empty for a 4-wire installation.
The shield wire will attach to the ground clamp on the backplate.
Load Cell Size Quantity of Cells Estimated Operating Time
350 Ohm Load Cell 1 80-95 hours
4 60-80 hours
700 Ohm Load Cell 1 85-100 hours
4 70-90 hours
Table 2-2. Estimated Battery Operating Times
Connector Pin Function
J1 1 +SIG
2 –SIG
3 +SENSE
4 –SENSE
5 +EXC
6 –EXC
For 6-wire load cell connections,
remove jumpers JP1 and JP2.
Table 2-3. J1 Pin Assignments
Note
Note
Note
Note