Rice Lake Non-NTEP SENDit Kit User manual

RoughDeck HP SENDit
Portability Frames
SENDit Kit Assembly
Installation Manual
PN 216475 Rev AFebruary 27, 2023

© Rice Lake Weighing Systems. All rights reserved.
Rice Lake Weighing Systems® is a registered trademark of
Rice Lake Weighing Systems.
All other brand or product names within this publication are trademarks or
registered trademarks of their respective companies.
All information contained within this publication is, to the best of our knowledge, complete and
accurate at the time of publication. Rice Lake Weighing Systems reserves the right to make
changes to the technology, features, specifications and design of the equipment without notice.
The most current version of this publication, software, firmware and all other product
updates can be found on our website:
www.ricelake.com

Revision History
© Rice Lake Weighing Systems ● All Rights Reserved 3
Technical training seminars are available through Rice Lake Weighing Systems.
Course descriptions and dates can be viewed at www.ricelake.com/training
or obtained by calling 715-234-9171 and asking for the training department.
Revision History
This section tracks and describes manual revisions for awareness of major updates.
Revision Date Description
AFebruary 27, 2023 Initial manual release with product launch
Table i. Revision Letter History

Contents
RoughDeck HP SENDit Portability Frames
4 Visit our website www.RiceLake.com
Rice Lake continually offers web-based video training on a growing selection
of product-related topics at no cost. Visit www.ricelake.com/webinars
1.0 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.1 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.2 SENDit Kit Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.2.1 Non-NTEP Kit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.2.2 NTEP Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.2.3 Power Connection Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.3 SENDit Front Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1.4 FCC Compliance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.5 Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.0 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.1 Mounting Plate Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.2 Assembly and Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.2.1 Mounting Plate Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.2.2 Wire Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.3 Installing the Mounting Plate on the RoughDeck HP Frame. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.4 Connecting the SENDit Transmitter to the SENDit Receiver (non-NTEP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.5 Connecting the SENDit Transmitter to the MSI-8004HD Receiver (NTEP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3.0 Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.1 Initial Calibration with the SENDit Transmitter and SENDit Receiver (Non-NTEP). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.2 Calibration with SENDit Transmitter and SENDit Receiver. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.3 Initial Calibration with the SENDit Transmitter (NTEP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3.4 Calibration with SENDit Transmitter and MSI-8004HD (NTEP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3.4.1 Initial Receiver Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3.4.2 Routine Calibration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Introduction
© Rice Lake Weighing Systems ● All Rights Reserved 5
1.0 Introduction
The SENDit Wireless Load Cell Interface transmitters and receivers are efficient communication devices that replace the need
for traditional wire runs.This manual provides the details for SENDit installation, configuration and calibration to the RoughDeck
HP Floor Scale.
Manuals and additional resources are available from Rice Lake Weighing Systems at www.ricelake.com/manuals
Warranty information is available at www.ricelake.com/warranties
1.1 Safety
Safety Definitions:
DANGER: Indicates an imminently hazardous situation that, if not avoided, will result in death or serious injury. Includes
hazards that are exposed when guards are removed.
WARNING: Indicates a potentially hazardous situation that, if not avoided, could result in serious injury or death. Includes
hazards that are exposed when guards are removed.
CAUTION: Indicates a potentially hazardous situation that, if not avoided, could result in minor or moderate injury.
IMPORTANT: Indicates information about procedures that, if not observed, could result in damage to equipment or
corruption to and loss of data.
General Safety
Do not operate or work on this equipment unless this manual has been read and all instructions are understood.
Failure to follow the instructions or heed the warnings could result in injury or death. Contact any Rice Lake
Weighing Systems dealer for replacement manuals.
WARNING: Failure to heed could result in serious injury or death.
Do not allow minors (children) or inexperienced persons to operate this unit.
Do not jump on the scale.
Do not use for purposes other than weight taking.
Do not place fingers into slots or possible pinch points.
Do not use any load bearing component that is worn beyond 5% of the original dimension.
Do not use this product if any of the components are cracked.
Do not exceed the rated load limit of the unit.
Do not make alterations or modifications to the unit.
Do not remove or obscure warning labels.
Do not use near water.
Keep hands, feet and loose clothing away from moving parts.

RoughDeck HP SENDit Portability Frames
6 Visit our website www.RiceLake.com
1.2 SENDit Kit Overview
The SENDit kit comes with the 6V battery option kit and 6V battery charger. Other battery charging options are also available
for the SENDit kit (Section 1.2.3 on page 7).
1.2.1 Non-NTEP Kit
The non-NTEP kit includes a SENDit transmitter and SENDit receiver. The full kit includes:
Figure 1-1. Non-NTEP SENDit Kit
NOTE: The 9-pin cable (Item G) is only needed for the initial SENDit transmitter calibration.
Item Description Part No.
A Battery Tray 205652
B Battery 6V SLA w/ Power Jack 7000/7001 162173
C SENDit Unit Antenna 162178
D Antenna Bracket Mount 162452
E SENDit System Pair RF Matched 160312
F Cordset IP68 M12 4-Pin Male Shielded 164865
G Cable Assembly, Serial I/O DCE D9 Sockets 150964
Table 1-1. Non-NTEP SENDit Kit Parts
A
B
C
D
E
F
G

Introduction
© Rice Lake Weighing Systems ● All Rights Reserved 7
1.2.2 NTEP Kit
The NTEP kit includes a SENDit transmitter and MSI-8004HD receiver. The full kit includes:
Figure 1-2. NTEP SENDit Kit
NOTE: The 9-pin cable is only needed for the initial SENDit transmitter calibration.
1.2.3 Power Connection Options
The SENDit kit comes with the 6V battery option kit and 6V battery charger. Other battery options include:
Item Description Part No.
A Battery Holder Tray 205652
B Battery 6v Sla W/ Power Jack 7000/7001 162173
C SENDit Unit Antenna 162178
D Antenna Bracket Wall 162452
E 8004HD Display AC 210899
F SENDit Transmitter 160331
G Cordset IP68 M12 4-Pin Male Shielded 164865
H Cable Assembly, Serial I/O DCE D9 Sockets 150964
Table 1-2. NTEP SENDit Kit Parts
Part No Description Comments
162172 6V Battery Charger Universal Power, US Plug. Requires changing plug type for international sales.
162173 6V Battery Option Kit Battery (161679) and interface cable (159817)
162175 Enclosure for 6V SLA Battery Used for installations where the battery needs to be rigidly mounted.
160109 6V Wall Cube, US Plug Power Adapter, 12W 6VDC Wall Mount. Universal Input 90-264VAC. 2.1mm Coax Power Plug.
US, Canada, Japan
160110 6V Wall Cube,
International Plugs
Power Adapter, 18W 6VDC Wall Mount. Universal Input 90-264VAC. 2.1mm Coax Power Plug.
Contains blades for international mains. US, UK, Europe, Aus, China
Table 1-3. Power Connection Options
A
B
C
D
E
F
G
H

RoughDeck HP SENDit Portability Frames
8 Visit our website www.RiceLake.com
1.3 SENDit Front Panel
Figure 1-3. Transmitter Front Panel
Figure 1-4. Receiver Front Panel
Item No. Description
1 Load Cell connector (Transmitter) - located on the side of the unit.
mV/V Output (Receiver) - located on the side of the unit.
2 Transmitter Power LED – Indicates state of indicator power.
Steady short GREEN blinks – good battery (or AC power).
Two ORANGE blinks then a pause – low battery.
Four ORANGE blinks then a pause – very low battery.
Receiver Power LED – Indicates state of indicator power.
Steady short blinks – RF connected, good battery (or AC power).
Two short blinks then a pause – RF connected, low battery.
Four short blinks then a pause – RF connected, very low battery.
Steady long blinks – RF disconnected and good battery (or AC power).
Long blink, short blink then a pause – RF disconnected and low battery.
Long blink, three short blinks – RF disconnected and very low battery.
3 Power Button
Press & release – turns unit on
Press & hold for one to four seconds – will auto zero
Press & hold five seconds – turns unit off
4 Power In Connection – Located on the side of the unit. Type of power source will be checked on the overlay.
All SENDit units are currently 5-6 VDC.
5 Serial Port – located on the side of unit.
Table 1-4. Front Panel
2
1
3
4
5
2
1
3
4
5

Introduction
© Rice Lake Weighing Systems ● All Rights Reserved 9
1.4 FCC Compliance
United States
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
Canada
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio
Interference Regulations of the Canadian Department of Communications.
Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites applicables aux appareils
numériques de la Class A prescites dans le Règlement sur le brouillage radioélectrique edicté par le ministère des
Communications du Canada.
1.5 Frequently Asked Questions
Does the battery come out of the portability frame to be charged?
The battery can be removed or left in its holder for charging. Slide the mounting plate out of the portability frame to gain access
to the battery and connect the charger.
How long do the batteries last while in use?
Between charges, the battery life should be around 100 hours. It is recommended to charge the battery at the end of every shift,
and to keep an extra battery charged and ready to go. If there will be extended periods where the system will not be used, it is
recommended the battery be disconnected from the SENDit.
What is the part number for the spare battery?
162173
Will leaving a battery on the charger cause damage?
The charger has a “float” mode, meaning the battery will not be overcharged or damaged.

RoughDeck HP SENDit Portability Frames
10 Visit our website www.RiceLake.com
2.0 Installation
SENDit transmitter and receiver units are factory paired. Take care when unpacking orders of multiple units to keep the paired
sets together. In the event a transmitter or receiver must be replaced or the units must be re-paired, contact Rice Lake
Weighing Systems and have the Serial Number ready for the transmitter or receiver.
Immediately after unpacking, visually inspect the contents to ensure all components are included and undamaged. If any parts
were damaged in shipment, notify Rice Lake Weighing Systems and the shipper immediately.
Ensure the battery is fully charged before installation and use. It is recommended to charge the battery overnight to ensure it is
fully charged and ready for use.
Tools Required for Installation:
• Flathead screwdriver
• 3/32 inch hex key wrench
• 1/8 inch hex key wrench
• 5/32 inch hex key wrench
• Blue Thread Lock (Recommended)
2.1 Mounting Plate Layout
The mounting plate holds the contents of the kit in place. When installing, ensure every piece is placed in the correct spot.
Figure 2-1. Mounting Plate Overview
Location Description
A Battery Tray
B Antenna Bracket Mount
C SENDit
Table 2-1. SENDit Mounting Kit Location
A
B
C

Installation
© Rice Lake Weighing Systems ● All Rights Reserved 11
2.2 Assembly and Wiring
IMPORTANT: A standard antenna and the antenna mount bracket mount are not meant for water-based environments.
2.2.1 Mounting Plate Assembly
1. Set the battery tray in its designated mounting location.
2. Using the 1/8 inch hex key wrench, install the battery tray onto the mounting plate assembly with the provided 1/8 inch
screws.
NOTE: Blue thread lock is recommended for installing the lock washers on the 1/8 inch screws during the battery tray
installation.
Figure 2-2. Battery Tray Installation
3. Set the SENDit Transmitter in its designated mounting location.
4. Using a 3/32 inch hex key wrench, install SENDit Transmitter onto mounting plate assembly using the provided 3/32
inch screws.
NOTE: Blue thread lock is recommended for installing the lock washers on the 3/32 inch screws during the SENDit
Transmitter installation.
Figure 2-3. SENDit Transmitter Installation

RoughDeck HP SENDit Portability Frames
12 Visit our website www.RiceLake.com
5. Set the antenna bracket mount in its designated mounting location.
NOTE: The vertical side of the antenna bracket mount needs to face away from the SENDit transmitter.
As shown in Figure 2-5.
6. Using the 5/32 inch hex key wrench, install antenna bracket mount onto the mounting plate assembly with provided 5/
32 inch screws.
NOTE: Blue thread lock is recommended for installing the lock washers on the 5/32 inch screws during the antenna bracket
mount installation.
Figure 2-4. Antenna Bracket Mount Installation
7. Install the antenna onto the antenna mounting bracket.
Figure 2-5. Antenna Installation
8. Once the antenna is installed, ensure the antenna is pointed upwards.
NOTE: The direction of the antenna must point upwards at all times in order to obtain a proper signal.
9. Set the battery in the battery tray with cable orientated towards the SENDit Transmitter. See Figure 2-5.
IMPORTANT: When installing the battery, ensure that the battery power cable is facing towards the SENDit Transmitter.

Installation
© Rice Lake Weighing Systems ● All Rights Reserved 13
2.2.2 Wire Connections
1. Connect the coaxial antenna wire to the SENDit transmitter and the antenna bracket mount.
Figure 2-6. Antenna Wiring
2. Connect the Power In wire from the SENDit transmitter to the battery terminal wire. Once connected, the SENDit
Transmitter will blink to indicate that it has been connected.
Figure 2-7. Power Input Wiring
3. Wind up all loose wiring and place in a secure location on the mounting plate.
IMPORTANT: All wires must be wound up and placed away from the RoughDeck mounting plate insertion slots to avoid
pinching and wire damage.
Power Input Cable 6VDC Battery Connector
or
120VAC Power
Adapter Connector

RoughDeck HP SENDit Portability Frames
14 Visit our website www.RiceLake.com
2.3 Installing the Mounting Plate on the RoughDeck HP Frame
IMPORTANT: The scale must be lifted from a side that is away from the junction box.
WARNING: The RoughDeck HP is heavy and could cause bodily harm if body parts are caught under it when installing. Do
not lift the scale while loaded. Ensure that the scale is balanced when lifting.
1. Lift the scale from an acceptable side of the RoughDeck HP Frame. See Table 2-8 for acceptable sides that the scale
can be lifted from.
Figure 2-8. Proper Lifting Sides
2. Remove the homerun cable from underneath the scale.
3. Discard the homerun cable as it will not be used for this installation.
4. Lower the scale into the frame.
5. Align the junction box mounting plate on the mounting plate frame. See Figure 2-10 on page 15.
6. Open the junction box face plate.
7. Feed the blunt-end wiring through the junction box slot on the RoughDeck HP frame.
8. Insert the 4-pin load cell cable (PN 164865) through an available strain relief.
3
2
3
3

Installation
© Rice Lake Weighing Systems ● All Rights Reserved 15
9. Connect the 4-pin load cell cable to the Load Cell Input connection cable on the SENDit transmitter. SeeTable 2-2
and Figure 2-9 for wiring information.
10. Close the junction box face plate.
11. Slide the mounting plate into the RoughDeck HP Frame.
NOTE: Ensure the antenna is pointed upwards, through the notch in the frame, in order to obtain a proper signal.
Figure 2-10. Mounting Plate Install
12. Set the cover plate onto the cover plate bolts.
13. Install wing nuts on the baseplate cover. See Figure 2-11.
NOTE: Access to the mounting plate is needed during calibration (Section 3.0 on page 17).
Figure 2-11. Cover Plate Installation
Figure 2-9. SENDit Transmitter Cable Connection
SENDit
Connector Pin # Wire Color Function
1 Brown +Excitation
2 White -Excitation
3 Blue +Signal
4 Black -Signal
Table 2-2. Load Cell Wiring
Male Connector
1
2
3
4

RoughDeck HP SENDit Portability Frames
16 Visit our website www.RiceLake.com
2.4 Connecting the SENDit Transmitter to the SENDit Receiver (non-NTEP)
1. Connect the SENDit Transmitter to the battery, if not connected previously.
2. Connect the SENDit Receiver to the indicator. See the indicator manual for proper connection information.
3. Power on the SENDit Transmitter on the mounting plate in the frame.
4. Power on the SENDit Receiver.
The SENDit transmitter and the SENDit receiver should automatically pair together. If they do not pair, contact Rice Lake
Weighing Systems for assistance.
When the SENDit Transmitter is on and connected, it should show steady, green blinks to indicate that the RF is connected and
there is a good battery charge. If the LED flashes are different than the steady, green blinks, see Section 1.3 on page 8 for more
information.
2.5 Connecting the SENDit Transmitter to the MSI-8004HD Receiver (NTEP)
1. Connect the SENDit Transmitter to the battery, if not connected previously.
2. Power on the SENDit Transmitter on the mounting plate in the frame.
3. Power on the MSI-8004HD Receiver.
The SENDit transmitter and the MSI-8004HD should automatically pair together. If they do not pair, contact Rice Lake Weighing
Systems for assistance.
When the SENDit Transmitter is on and connected, it should show steady, green blinks to indicate that the RF is connected and
there is a good battery charge. If the LED flashes are different than the steady, green blinks, see Section 1.3 on page 8 for more
information.

Calibration
© Rice Lake Weighing Systems ● All Rights Reserved 17
3.0 Calibration
3.1 Initial Calibration with the SENDit Transmitter and SENDit Receiver (Non-NTEP)
1. Power on the SENDit transmitter and the SENDit receiver.
2. Using the 9-pin serial cable, connect the transmitter to a computer. This allows setup with the MSI TranSend mV/
SENDit Scale Calibration program.
3.2 Calibration with SENDit Transmitter and SENDit Receiver
Use the following instructions to calibrate the SENDit receiver unit. The MSI mV Scale Calibration software can be downloaded
from the Rice Lake Weighing Systems website.
1. Power on the transmitter and receiver units.
2. On the connected computer, navigate to the MSI mV Scale Calibration program.
3. Double click .
4. Select Calibration from the drop-down menu.
Figure 3-1. Calibration
5. Press .

RoughDeck HP SENDit Portability Frames
18 Visit our website www.RiceLake.com
6. Select the COM port the SENDit receiver is connected to from the drop-down menu.
NOTE: If no COM port selection is available, ensure the serial cables are properly connected, the drivers are installed properly
and that the SENDit Pair is powered up. Once an acceptable connection has been made, restart the Calibration program.
NOTE: The drivers are for USB-to-Serial conversion that can be used to connect the computer to the scale. If the PC won’t
connect to the scale, go to the USB-to-Serial converter manufacturer's website to update the drivers.
Figure 3-2. COM Port Selection
7. Check the Advanced Mode dialogue box to change the upper and lower range percent detected by the SENDit
system, if necessary.
Figure 3-3. Advanced Mode
8. Press .
9. Enter the total scale capacity.
Figure 3-4. Scale Capacity

Calibration
© Rice Lake Weighing Systems ● All Rights Reserved 19
10. Press .
11. Ensure all weight is removed from the scale.
Figure 3-5. Zero Calibration
12. When scale is stable, press .
Figure 3-6. Span Calibration
13. Load test weights onto the scale.
14. Enter the test weight total value in the weight dialogue box.
15. Press . Calibration Complete displays.
Figure 3-7. Calibration Complete
16. Press to return to the calibration start display.

RoughDeck HP SENDit Portability Frames
20 Visit our website www.RiceLake.com
3.3 Initial Calibration with the SENDit Transmitter (NTEP)
The NTEP SENDit connects to an MSI-8004HD.
1. Power on the SENDit transmitter and MSI-8004HD.
2. Using the 9-pin serial cable, connect the transmitter to a computer. This allows setup with the MSI TranSend mV/
SENDit Scale Calibration program.
3.4 Calibration with SENDit Transmitter and MSI-8004HD (NTEP)
NOTE: It is required that the weight used is at least 10% of full capacity in order to achieve rated accuracy.
If the unit has been sealed and standard is set to  or , the setup menu is not available. To calibrate, the CAL button
must be pressed.
3.4.1 Initial Receiver Calibration
Initial calibration is used to setup units, capacity and resolution (d) required for the load cell or after a calibration reset.
Set an F-key and press the programmed F-Key to scroll to the load cell to be calibrated.
1. Press to select the load cell to be calibrated.
2. Press and simultaneously.  displays.
3. Press .  displays.
4. Press . The default units display.
5. Press to scroll through the available units.
6. With desired unit displayed, press to select.  is displayed.
7. Press . The default capacity is displayed.
8. To enter a different capacity, press .
9. Press to scroll through numbers and to save the selected number and move to next digit.
10. When correct capacity is displayed, press to store the value.  displays.
11. Press . The default display divisions are displayed.
12. Press to scroll through the available display divisions.
13. With desired display division displayed, press to select.  displays.
Proceed with the routine calibration, starting with Step 2 on page 21.
CHAN
F2
ZERO
CHAN
F2
UNITS
F1
UNITS
F1
CHAN
F2
UNITS
F1
UNITS
F1
CHAN
F2
CHAN
F2
UNITS
F1
UNITS
F1
UNITS
F1
CHAN
F2
UNITS
F1