Rice Lake TE Series User manual

Rice Lake TE Series
Tuning Fork Enhanced Balance
Operation Manual
PN 185193 Rev BMay 6, 2021

An ISO 9001 registered company
© Rice Lake Weighing Systems. All rights reserved.
Rice Lake Weighing Systems® is a registered trademark of
Rice Lake Weighing Systems.
All other brand or product names within this publication are trademarks or
registered trademarks of their respective companies.
All information contained within this publication is, to the best of our knowledge, complete and
accurate at the time of publication. Rice Lake Weighing Systems reserves the right to make
changes to the technology, features, specifications and design of the equipment without notice.
The most current version of this publication, software, firmware and all other product
updates can be found on our website:
www.ricelake.com

Contents
© Rice Lake Weighing Systems ● All Rights Reserved i
Contents
Technical training seminars are available through Rice Lake Weighing Systems.
Course descriptions and dates can be viewed at www.ricelake.com/training
or obtained by calling 715-234-9171 and asking for the training department.
1.0 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.1 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1.2 FCC Compliance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1.3 For More Accurate Measurements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.3.1 Measuring Environment Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.3.2 Specimen Related Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.3.3 Balance Main Unit Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.0 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.1 Unpack Balance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.1.1 Connections and Part Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.2 Assemble Balance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.2.1 Round Pan Base Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.2.2 Square Pan Base Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.3 Battery Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.4 Leveling the Balance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.5 Draft Shield Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.5.1 Draft Shield Assembly Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3.0 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3.1 Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3.1.1 NTEP Only Models. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3.1.2 NTEP / Measurement Canada Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3.1.3 Front Panel Item Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.2 Power On/Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.2.1 Standby . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3.2.2 Balance Operation Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3.3 Display Navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3.4 Zero-Point Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3.4.1 Zero-Point Adjustment Limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3.5 Tare Value. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.5.1 Preset Tare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.5.2 Check Tare Weight Using an F-Key. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.5.3 Add to Product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.6 Weigh Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.7 Counting Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.7.1 Actual Value Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
3.7.2 Numeric Value Setting Method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
3.8 Percentage Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3.9 Coefficient Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3.10 Specific Gravity Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.10.1 Menus Available in Operation Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.10.2 Materials Required in Specific Gravity Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.10.3 Prepare Equipment to Measure Specific Gravity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.10.4 Measure the Specific Gravity Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.11 Statistics Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
3.11.1 Menus Available in Operation Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
3.11.2 Selecting Statistic Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

TE Series Tuning Fork Enhanced Balance
ii Visit our website www.RiceLake.com
Rice Lake continually offers web-based video training on a growing selection
of product-related topics at no cost. Visit www.ricelake.com/webinars
Contents
3.12 Animal Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
3.12.1 Weigh Animal Using Manual Hold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
3.13 Formulation Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
3.13.1 Data Review. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
3.14 Unit Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
3.15 Comparator Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
3.16 Addition Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
3.16.1 Weighing with Plus Side Addition. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
3.16.2 Weighing with Minus Side Addition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
3.16.3 View/Delete Total Value. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
3.17 Tare-Subtraction Reminder Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
3.17.1 Set Tare-Subtraction Reminder Function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
3.18 Zero-Point-Adjustment Reminder Function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
3.18.1 Set Zero-Point-Adjustment Reminder Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
3.19 Stabilization Wait Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
3.19.1 Set Stabilization Wait Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
3.20 Bar Graph Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
3.21 Back Light Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
3.22 Auto Off Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
3.23 Simple Self Counting System (SCS) Method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
3.23.1 Set SCS Method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
4.0 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
4.1 General Navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
4.2 Numeric Value Entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
4.2.1 General Entry for All Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
4.2.2 For NTEP Only Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
4.2.3 For NTEP / Measurement Canada Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
4.3 Applications Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
4.3.1 Operation Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
4.3.2 NTEP Only Model Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
4.3.3 NTEP / Measurement Canada Model Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
4.3.4 Comparator Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
4.3.5 Addition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
4.4 Performance Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
4.4.1 Stability. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
4.4.2 Response Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
4.4.3 Zero Tracking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
4.5 User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
4.5.1 Preset Tare Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
4.5.2 Input Preset Tare Value . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
4.5.3 Set the Discrimination Value of Comparator Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
4.6 External Input/Output Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
4.7 Lock Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
4.7.1 Total Lock Release . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
4.7.2 Key Lock Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
4.7.3 Menu Lock Function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Contents
© Rice Lake Weighing Systems ● All Rights Reserved iii
Contents
Technical training seminars are available through Rice Lake Weighing Systems.
Course descriptions and dates can be viewed at www.ricelake.com/training
or obtained by calling 715-234-9171 and asking for the training department.
4.8 Admin/Adjust Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
4.8.1 Set Short Cut Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
4.8.2 Set Free Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
4.8.3 Maintenance Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
4.8.4 Balance Manage Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
4.9 LCD Display Characters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
4.9.1 7-Segment Characters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
4.9.2 16-Segment Characters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
5.0 Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
5.1 Perform External Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
5.2 Perform External Span Calibration Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
5.3 Sealing Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
5.3.1 Sealing Method 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
5.3.2 Sealing Method 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
6.0 Communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
6.1 RS-232 Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
6.2 USB Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
6.3 Basic Data Output Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
6.3.1 Data Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
6.4 CBM Data Output Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
6.4.1 Data Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
6.5 Input Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
6.5.1 Input Command Composition 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
6.6 Command Formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
6.6.1 Input Command Composition 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
6.7 Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
6.8 External Contact Input. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
6.9 Communication Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
6.10 Set Communication Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
6.10.1 Relay Contact Output (Option). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
6.11 USB Communication and Bus Power Inputs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
6.12 Print Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
7.0 Troubleshooting and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
7.1 Maintenance Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
7.2 Basic Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
7.2.1 Cleaning—Round Pan Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
7.2.2 Cleaning—Square Pan Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
7.3 Error Messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
8.0 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
8.1 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
8.2 Model Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
8.3 Basic Communication Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
8.4 Certifications and Approvals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
8.5 Functional Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

TE Series Tuning Fork Enhanced Balance
iv Visit our website www.RiceLake.com
Rice Lake continually offers web-based video training on a growing selection
of product-related topics at no cost. Visit www.ricelake.com/webinars
Contents

Introduction
© Rice Lake Weighing Systems ● All Rights Reserved 1
1.0 Introduction
This document describes how to assemble and operate the Rice Lake TE Series Tuning Fork Enhanced Balance.
Manuals and additional resources are available from the Rice Lake Weighing Systems website at www.ricelake.com
Warranty information can be found on the website at www.ricelake.com/warranties
Figure 1-1. Rice Lake TE Balances
Part No. Model No. Capacity Readability (e) Readability (d) Pan Size
187600 TE-223 220 g 0.001 g 0.01 g 4.6'' Diameter
186030 TE-623 620 g 0.001 g 0.01 g 4.6'' Diameter
186035 TE-3202 3,200 g 0.01 g 0.1 g 6.3'' x 7.1''
186036 TE-6202 6,200 g 0.01 g 0.1 g 6.3'' x 7.1''
186037 TE-15001 15,000 g 0.1 g 1 g 6.3'' x 7.1''
Table 1-1. Available NTEP Only Models
Part No. Model No. Capacity Readability (e=d) Pan Size
204688 TE-322NC 320 g 0.01 g 4.6'' Diameter
204689 TE-1501NC 1500 g 0.1 g 6.3'' x 7.1''
204690 TE-8200NC 8200 g 1 g 6.3'' x 7.1''
Table 1-2. Available NTEP / Measurement Canada Models
Part No. Description
186074 Power supply 100-240 VAC, 50-60 Hz
186075 In-use dust cover 1,200 g models and lower
186076 In-use dust cover 3,200 g models and higher
186077 Specific Density Measurement Kit
186079 Ethernet TCP/IP option card
Table 1-3. Available Options

TE Series Tuning Fork Enhanced Balance
2 Visit our website www.RiceLake.com
1.1 Safety
Safety Signal Definitions:
Indicates an imminently hazardous situation that, if not avoided, will result in death or serious injury. Includes
hazards that are exposed when guards are removed.
Indicates a potentially hazardous situation that, if not avoided, could result in serious injury or death. Includes
hazards that are exposed when guards are removed.
Indicates a potentially hazardous situation that, if not avoided, could result in minor or moderate injury.
Indicates information about procedures that, if not observed, could result in damage to equipment or corruption
to and loss of data.
General Safety
Do not operate or work on this equipment unless this manual has been read and all instructions are understood.
Failure to follow the instructions or heed the warnings could result in injury or death. Contact any Rice Lake
Weighing Systems dealer for replacement manuals.
Failure to heed could result in serious injury or death.
Do not allow minors (children) or inexperienced persons to operate this unit.
Don not operate unless unit is completely assembled.
Do not use for purposes other than weight taking.
Do not exceed the rated specification of the unit.
Do not remove or obscured warning labels.
Do not use in wet locations or with wet hands.
Do not use solvents or aggressive substances to clean the unit.
Review MSDS (Material Safety Data Sheets) when applicable.
Only use the specified power supply supplied by Rice Lake Weighing Systems.
Do not disassemble or modify the unit. For inspection and adjustments, contact Rice Lake Weighing Systems.
Do not use in an explosive environment.
1.2 FCC Compliance
United States
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
Canada
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio
Interference Regulations of the Canadian Department of Communications.
Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites applicables aux appareils
numériques de la Class A prescites dans le Règlement sur le brouillage radioélectrique edicté par le ministère des
Communications du Canada.
DANGER
WARNING
CAUTION
IMPORTANT
WARNING

Introduction
© Rice Lake Weighing Systems ● All Rights Reserved 3
1.3 For More Accurate Measurements
To make more accurate measurement, it is necessary to lessen error-causing factors in measurement to the extent possible.
Error-causing factors include not only an instrument error and performance of the balance itself but also the nature and
condition of a specimen, measuring environment (vibration, temperature, humidity, etc.) and the like. These factors will directly
affect measurement result in the case of a balance with high resolution capability.
Figure 1-2. Measurement Error Factors
1.3.1 Measuring Environment Precautions
Temperature / Humidity / Air Draft / Atmospheric Pressure / Dust
• Keep the room temperature constant to avoid condensation and indication drift due to temperature changes
• Avoid exposure to direct sun that can cause abrupt temperature changes
• Low humidity can cause static electricity, resulting in inaccurate measurements
• Avoid exposure to airflow (air conditioner, heat ducts)
• Change of atmospheric pressure can cause a change of buoyancy of the air on the specimen and mechanism of the
balance, resulting in inaccurate measurements
• Avoid locations that are subject to dust
Vibration / Shaking
• When possible, locate balance in a room on the first floor or basement
• Rooms near a road/railroad should be avoided
• Place balance on a table/counter that is not affected by vibration
• Placing a sheet of soft cloth or paper under the balance can cause shaking
Gravity
• The latitude and altitude of a measuring location can affect a weight reading due to changes in gravity
• Calibrate the balance at a measuring location to account for location gravity
Electromagnetic Wave
• Avoid locations where strong electromagnetic wave generating objects are present
• Avoid using tables that are subject to magnetism or static electricity
Measuring Room
Measurement Errors
Balance
Measuring Table
Sample
Maintenance
Calibration
Temperature
Vibration / Shaking
Gravity
Static Electricity
Temperature
Vibration /
Shaking
Magnetism
Humidity
Drafts
Electromagnetic Waves
Static Electricity
Absorption /
Evaporation
of Moisture
Magnetism

TE Series Tuning Fork Enhanced Balance
4 Visit our website www.RiceLake.com
1.3.2 Specimen Related Precautions
Static Electricity
• Synthetic resin- and glass-made specimens are easily electrically charged
• Weighing electrically charged specimens make the displayed value unstable, reducing the reproducibility of a test result
• Neutralize electrically charged specimens before measurement
Magnetism
• Specimens affected by magnetism weigh differently depending on the position on the pan, reducing reproducibility
• Eliminate the magnetism or place the specimens on a container/plate to protect the weighing mechanism
Moisture Absorption/Evaporation
• Wet or volatile specimens can cause the displayed value to continuously fluctuate due to evaporation
• Put these specimens in a container with a tight fitting lid to prevent evaporation during the weighing process
Specimen Temperature
• Difference in temperature between specimens and the draft shield interior generates convection flow, causing errors
• If specimen temperature is excessively high or low, allow its temperature to stabilize at room temperature prior to
measuring
• Ensure the draft shield interior temperature is equal to room temperature prior to measuring
• Body temperature of operator affects measurement results; handle specimens with tweezers and refrain from putting
hands in the draft shield during operation
1.3.3 Balance Main Unit Precautions
Operating precautions
• If a dust cover is used, wipe with an anti-static agent or remove the cover
• For stability, turn on the balance 30 minutes or more and load the balance a few times with a calibration weight
equivalent to the weighing capacity prior to using
Adjustment
• Calibrate balance periodically with an external adjustment weight or internal adjustment weight, external is more precise
• Adjustment is needed when:
• Using the balance for the first time
• Using the balance after a long period of non-use
• Relocating the balance
• A major change in temperature, humidity or atmospheric pressure has happened
Maintenance
• Remove any dust or liquid from the pan and/or pan base prior to operation
• Ensure that no dust or liquid enters the balance when cleaning
• Frequent cleaning of the balance is required

Installation
© Rice Lake Weighing Systems ● All Rights Reserved 5
2.0 Installation
Use balance only in areas free from environmental conditions that could affect the accuracy ( Section 1.3 on page 3 ).
Legal for Trade balance must be verified and sealed (Section 5.3 on page 57).
2.1 Unpack Balance
Unpack the balance and inspect the contents. Report missing or damaged components to the shipper and Rice Lake Weighing
Systems immediately.
Figure 2-1. Balance Components
IMPORTANT
Draft Shield
Round Pan
Round Pan Base
Balance Base
Square Pan
Square Pan Base
Pan Base Screw
Balance Base
Round Pan Balance Components Square Pan Balance Components
Adapter with
Attachments
Sealing Kit Sealing Kit

TE Series Tuning Fork Enhanced Balance
6 Visit our website www.RiceLake.com
2.1.1 Connections and Part Locations
Figure 2-2. Connection and Part Locations
Item No. Description
1 Draft shield (Section 2.5 on page 10)
2 Weighing pan
3 Level
4 Adjustable Feet
5 Display
6 Battery case
7 AC adapter jack
8 USB connector (Type B)
9 RS-232C connector (D-sub 9 pin male)
10 Option slot
11 Adapter with attachments
Table 2-1. Parts and Locations
2
34
5
6
7
8
9
10
2
3
4
5
6
7
8
9
10
1
11
Round Pan Type
Square Pan Type

Installation
© Rice Lake Weighing Systems ● All Rights Reserved 7
2.2 Assemble Balance
Use the following steps to assemble the balance.
2.2.1 Round Pan Base Assembly
Figure 2-3. Assemble Base
1. Ensure the lock plate is in the unlocked position.
2. Set the pan base on the balance.
3. Slide the lock into the locked position.
4. Mount the weighing pan.
5. Connect the AC adapter or insert batteries (Section 2.3 on page 8).
6. Assemble and install the draft shield (Section 2.5 on page 10).
2.2.2 Square Pan Base Assembly
Figure 2-4. Square Base Assembly
1. Ensure the word Front is aligned towards the display of the balance and attach the pan base to the balance.
2. Tighten the pan base screw firmly.
3. Place the weighing pan on the pan base.
4. Connect the AC adapter or insert batteries (Section 2.3 on page 8).
Pan Base
Screw

TE Series Tuning Fork Enhanced Balance
8 Visit our website www.RiceLake.com
2.3 Battery Installation
Use the following steps to install four AA batteries into the unit. Alkaline, manganese and nickel-metal hydride batteries can be
used. Approximate battery life is 150 hours using alkaline batteries with the back-light and external output off.
Figure 2-5. Install Batteries
1. Pull out the battery case.
2. Insert four AA batteries into battery case. Make sure to insert batteries with the positive and negative poles correctly
inserted.
3. Insert battery case back into the unit until it clicks in place. When the balance is battery operated, one of the icons
below will display:
Full Charge
Low Charge
Replace Batteries
Observe the following statements when changing or replacing the batteries.
• If the balance is not going to be used for a long period of time remove the batteries
• Dispose of used batteries in accordance with state and local regulations
• Do not use batteries that leak or are damaged
• Only use new batteries in the balance, never mix used and new batteries or different brands/manufacturers
IMPORTANT

Installation
© Rice Lake Weighing Systems ● All Rights Reserved 9
2.4 Leveling the Balance
Use the following steps to level the balance.
1. Turn the adjustable feet as shown in Figure 2-6 to unlock them.
Figure 2-6. Unlock Adjustable Feet
2. Adjust balance feet until the bubble level is centered in the center circle. See Figure 2-7 for illustrated directions for
adjusting the feet to level the balance by moving the bubble into the center.
Figure 2-7. Level the Balance
or
or or or

TE Series Tuning Fork Enhanced Balance
10 Visit our website www.RiceLake.com
2.5 Draft Shield Assembly
The draft shield for round pan balance models must be assembled using the following steps.
1. Place the draft shield base on a flat, level surface.
2. Insert one of the rear panel supports into the bottom frame as shown in Figure 2-8. Ensure flat side is on the outside.
Figure 2-8. Install Rear Panel Supports
3. Secure the rear panel support to the base with a provided screw and repeat for the other side.
4. Insert the rear glass panel into the slots of the back supports.
5. Insert the front glass panel into the base, ensuring it clicks as shown in Figure 2-9.
Figure 2-9. Insert Front and Rear Panels
6. Gently place top assembly support on unit and carefully connect to the front glass panel.
Figure 2-10. Install Top Assembly
Rear panel
support Rear panel support
Draft shield base
Screw
Rear glass
panel
Front glass
panel
Ensure the front panel clicks
into the bottom frame
Top assembly
support

Installation
© Rice Lake Weighing Systems ● All Rights Reserved 11
7. Place the upper side brackets on top of the assembly as shown in Figure 2-11 and secure with provided screws.
Figure 2-11. Install Upper Brackets
8. Slide the top door assembly, with the handle towards the front, into the top brackets as shown in Figure 2-12. Ensure
the side rails of the top assembly are in the grooves in the top brackets.
Figure 2-12. Install Top Panel
9. Place the glass side panels together ensuring the rollers are on the outside. Use one panel with the handle and one
without as a pair.
10. Hold the panels together, ensuring the panel with the handle is facing outward. With the panels held tightly together,
insert the rollers into the frame of the top assembly as shown in Figure 2-13.
Figure 2-13. Insert Side Assemblies
Screw
Screw
Upper side
bracket
Top assembly
support
Top assembly
Rails must slide
into the grooves
Insert rollers into the top frame,
ensuring they are in the outside guides

TE Series Tuning Fork Enhanced Balance
12 Visit our website www.RiceLake.com
11. Push the pair as far as they will go, there is a stop for the inside panel.
12. Slide the outer panel to the front of the assembly.
13. Insert the panel stops as shown in Figure 2-14. Orient them with the wider end on the stop to the outside.
14. Press them until they are seated completely in the top brackets.
Figure 2-14. Insert Panel Stops
15. Ensure the latch on the back of the draft shield is in the up position.
16. Place the completed draft shield assembly on the balance as shown in Figure 2-15.
Figure 2-15. Install Draft Shield on Balance
17. Gently position the draft shield assembly toward the back of the balance to seat it in the slots of the balance.
18. Rotate the latch to the down position securing the draft shield assembly to the balance.
Do not move balance by holding the draft shield. Make sure to hold the main body of the balance to move it.
Panel Stops
Latch in up
position
Latch in down
position
IMPORTANT

Installation
© Rice Lake Weighing Systems ● All Rights Reserved 13
2.5.1 Draft Shield Assembly Parts
Figure 2-16. Draft Shield Parts
Item No. Description
1 Draft Shield Base
2 Rear Panel Support, Plastic
3 Rear Glass Panel
4 Front Glass Panel
5 Top Assembly Support
6 Left Upper Side Bracket
7 Right Upper Side Bracket
8 Left Door Assembly
9 Right Door Assembly
10 Top Door Assembly
11 Draft Shield Stopper
12 Screw (No. 1, White, d=3, L-8)
Table 2-2. Draft Shield Parts List
1
2
3
4
5
6
7
8
9
10
11
12

TE Series Tuning Fork Enhanced Balance
14 Visit our website www.RiceLake.com
3.0 Operation
This section lists the front panel display and button descriptions, necessary operation related precautions, and walks through
using the eight modes of operation, as well as the other functions used during the operation of the balance.
Calibrate the balance when it is installed or relocated and always adjust the level of the balance before use.
Do not apply excessive force to or impact the balance. Carefully place samples on the balance.
Shortcuts for various modes/functions can be assigned to F-keys (Section 4.8 on page 51).
3.1 Front Panel
3.1.1 NTEP Only Models
Includes TE-223, TE-623, TE-3202, TE-6202, and TE-15001 models.
Figure 3-1. Front Panel Display Overview (NTEP Only Models)
3.1.2 NTEP / Measurement Canada Models
Includes TE-322NC, TE-1501NC, and TE-8200NC models.
Tare key has been removed from the front panel for NTEP / Measurement Canada models.
Figure 3-2. Front Panel Display Overview (NTEP / Measurement Canada Models)
IMPORTANT
Note
1
2
3
5
4
6 7 8 9
14
13
12
15 2120
22
23
24
252525
11
10
18
17 19
16
Note
On/Off
Output
Zero
Zero
Menu
On/Off
F1 F2 F3 F4
1
4
2
4
3
6 7 8 9
14
13
12
15 21 20
23
24
252525
11
10
18
17 19
16