Rice Lake SCT-1SX Series User manual

SCT-1SX Series
Firmware version 01.21.01
Fieldbus Protocol
PN 221628 Rev A
January 4, 2024

© Rice Lake Weighing Systems. All rights reserved.
Rice Lake Weighing Systems® is a registered trademark of
Rice Lake Weighing Systems.
All other brand or product names within this publication are trademarks or
registered trademarks of their respective companies.
All information contained within this publication is, to the best of our knowledge, complete and accurate at the
time of publication. Rice Lake Weighing Systems reserves the right to make changes to the technology, features,
specications and design of the equipment without notice.
The most current version of this publication, software, rmware and all other product
updates can be found on our website:
www.ricelake.com

© Rice Lake Weighing Systems • All Rights Reserved 3
Contents
Connection 4
Fieldbus and Data Format Configuration 5
Data Reading (Input Area) 7
Alibi Memory "Page 1000" (0x03E8) 9
ADC Value "Page 3000" (0x0BB8) 10
µV Value "Page 3001" (0x0BB9) 11
Calibration 0 - Scale Parameters "Page 5000" (0x1388) 12
Calibration 1 - Calibration Points Weights "Page 5001" (0x1389) 13
Calibration 2 - Calibration Points ADC "Page 5002" (0x138A) 14
Calibration 3 - Legal State "Page 5003" (0x138B) 15
Calibration 4 - Filter and Metrical Parameters (1/2) "Page 5004" (0x138C) 16
Calibration 5 - Metrical Parameters (2/2) "Page 5005" (0x138D) 17
Calibration 6 - Condensed Calibration "Page 5006" (0x138E) 18
Advanced Filters "Page 5007" (0x138F) 19
Anti-Peak Filter "Page 5008" (0x139A) 20
Tare Type "Page 5010" (0x1392) 21
Transmitter SN and Firmware "Page 5011" (0x1393) 22
Unit of Measure 2 ("Conver" mode) "Page 5015" (0x1397) 23
Fieldbus Configuration "Page 5030" (0x13A6) 24
Profinet Name (only for SCT-1SX-PRONET) "Page 5031" (0x13A7) 25
Inputs Configuration "Page 5100" (0x13EC) 26
Outputs Configuration "Pages 5101 - 5104" (0x13ED - 13F0) 27
Analogue Output Configuration (1/3) "Page 5101" (0x13F6) 28
Analogue Output Configuration (2/3) "Page 5102" (0x13F7) 29
Analogue Output Configuration (3/3) "Page 5102" (0x13F8) 30
Setpoint Values (1/2) "Page 6100" (0x17D4) 31

4 Visit our website www.RiceLake.com
Setpoint Values (2/2) "Page 6101" (0x17D5) 32
Table 1 - Input Status Register 33
Table 2 - Output Status Register 33
Table 3 - Command Status Register 34
Table 4 - Alibi Status Register 34
Table 5 - Filter 35
Table 7 - Input Functions 35
Table 6 - Zero Tracking 35
Table 8 - Output Functions 35
Command Sending (Output Area) 36
Available Commands 37
Transmitter Configuration Via Fieldbus 38
Theoretical Calibration 38
Calibration 39
Calibration Linearization 40
Filter / Metric Parameters 1 41
Metric Parameters 2 42
Digital Inputs 43
Digital Output 1 44
Digital Output 2 45
Profinet Name 46
Scale Zeroing via Fieldbus 47
Mechanical Tare Zeroing via Fieldbus 47
Setup Backup and Restore via Fieldbus 48
Backup 48
Restore 48
Diagnostic Messages 49

© Rice Lake Weighing Systems • All Rights Reserved 5
+-
IN 2 IN 1 COM RL2 RL1
ETHERNET I/O PORT 1 ETHERNET I/O PORT 2
12 / 24 Vdc
RL4 RL3
8 9763 4 51 2
17 1619 18 15 14
LOAD CELL
i
SCT-1SX-E/IP, SCT-1SX-PRONET, SCT-1SX-MODTCP
Connection
The connection to the Fieldbus goes
through one of the two ETHERNET standard
connectors of the device.
Thank you for purchasing this product.
This manual contains fieldbus information for the following SCT-1SX digital weight transmitters:
• SCT-1SX-E/IP
• SCT-1SX-MODTCP
• SCT-1SX-PRONET
It is recommended that you carefully follow the instructions for programming the weight transmitter; performing actions not indicated in
this manual could compromise the functionality of the scale.
iManuals are available from Rice Lake Weighing Systems at www.ricelake.com/manuals
Warranty information is available at www.ricelake.com/warranties
Any problem with the product must be reported to the manufacturer or to the retailer where it was purchased.
Always TURN OFF THE POWER SUPPLY prior to installation or repair action.
Introduction

6 Visit our website www.RiceLake.com
888888 f.mode
A
tim.out
endian
Format
2
3
4
setup
BConfiG
1
fld.bus bus.typ
bus.typ
4 1
i
profin aut.CfG
ip.add
net.msk
Gat.way
Fieldbus and Data Format Configuration
The Fieldbus can be set through the configuration menu, following the procedure below:
•Restart the device.
•Press the key when 888888 is displayed.
2. Scroll the menu with the key until setup is displayed and press .
3. Scroll the menu with the key until fld.bus is displayed and press .
4. Selected the fieldbus type used and configure its parameters.
Depending on the selected Fieldbus, set the appropriate configuration parameters:
1. Access to the configuration menu:
MENU OVERVIEW
For Profinet:
The name of the Profinet node to use in the
project linked to the network master node is
dini <IP4>, <IP4> being the last Byte of the IP
address incorporated in the device configuration,
also when dynamic IP is used.
Ex. IP - 192.168.1.10, the node name will be dini-010.
If AUT.CFG parameter = YES, the IP address and
Profinet name can be assigned directly from the
network.
Dynamic IP configuration.
Static IP address.
Subnet mask.
Gateway.

© Rice Lake Weighing Systems • All Rights Reserved 7
i
eth.ip
mb.tCp
tim.out
endian
format
aut.CfG
aut.CfG
no
biG
uns.int
ip.add
ip.add
yes
little
float
siG.int
net.msk
net.msk
Gat.way
Gat.way
tim.out endian format
This parameter changes the order of the data sent to and received from the PLC. If data is available but does not relate to
data on the display, try changing this parameter.
For Ethernet/IP:
For Modbus TCP:
MENU OVERVIEW
"Time out" error message displayed only once.
"Time out" error message repeated.
Big Endian.
Unsigned integer (read the sign from Input status register).
Little Endian.
Float.
Signed integer.
Dynamic IP configuration.
Dynamic IP configuration.
Static IP address.
Static IP address.
Subnet mask.
Subnet mask.
Gateway.
Gateway.

8 Visit our website www.RiceLake.com
...
Byte 0
Byte 15
Byte 16
Byte 31
Byte 0
Byte 15
Byte 16
Byte 31
Byte 0
Byte 15
Byte 16
Byte 31
Data Reading (Input Area)
• The available data are divided into pages.
• To display data from pages 5xxx you must first send the command 35 (0x23) "LETTURA DATI".
• Depending on the Fieldbus, the data area size can be up to 128 Bytes.
• The size of each SCT-1SX page is 32 Bytes (therefore, even if the page size is 64 or 128 Bytes, only the first 32 available Bytes
• are used).
• The first 16 Bytes of each page always include the data concerning weight and weighing system status.
• Bytes 16 to 31 contain additional information, depending on the selected page (setup data, alibi memory etc.)
• The page selected by default is:
• - 3001 (0x0BB9).
• In factory configuration the data format is Big Endian. To change the format, follow the procedure on page 6.
• Weight data are expressed with unsigned integers. (Es. 12,345 0x3039). To change it, follow the procedure at page 6.
• V and ADC points are always expressed with positive and negative integers. (Ex. -12,345 0xCFC7).
Model of the pages in the Input Area:
Page 1000 Page 3000 Page 3001
Alibi
memory
Weight data
+
System status
diagnostics
ADC points
of each channel
Weight data
+
System status
diagnostics
V value
of each channel
Weight data
+
System status
diagnostics

© Rice Lake Weighing Systems • All Rights Reserved 9
(*) page selected by default at power-up.
Available Pages
Page Name Desciption Read Write
1000 (0x03E8) Alibi memory See page 9
3000 (0x0BB8) ADC values See page 10
3001 (0x0BB9) µV values (*) See page 11
5000 (0x1388) Calibration 0 - Scale parameters See page 12
5001 (0x1389) Calibration 1 - Calibration points weights See page 13
5002 (0x138A) Calibration 2 - Calibration points ADC See page 14
5003 (0x138B) Calibration 3 - Legal state See page 15
5004 (0x138C) Calibration 4 - Filter and metrical parameters (1/2) See page 16
5005 (0x138D) Calibration 5 - Metrical parameters (2/2) See page 17
5006 (0x138E) Calibration 6 - Quick calibration See page 18
5007 (0x138F) Advanced filters See page 19
5008 (0x1390) Anti-peak filter See page 20
5010 (0x1392) Tare type See page 21
5011 (0x1393) Transmitter SN and firmware See page 22
5015 (0x1397) Unit of measure 2 ("CoNVER" mode) See page 23
5030 (0x13A6) Fieldbus configuration See page 24
5031 (0x13A7) Profinet name (only for SCT-1SX) See page 25
5100 (0x13EC) Inputs configuration See page 26
5101 (0x13ED)
...
5104 (0x13F2)
Outputs configuration See page 27
5110 (0x13F6) Analog output configuration (1/3) See page 28
5111 (0x13F7) Analog output configuration (2/3) See page 29
5112 (0x13F8) Analog output configuration(3/3) See page 30
6100 (0x17D4) Setpoints values (1/2) See page 31
6101 (0x17D5) Setpoints values (2/2) See page 32

10 Visit our website www.RiceLake.com
Alibi Memory "Page 1000" (0x03E8)
Byte Modbus TCP
Register Big Endian Dato Little Endian
030001 B3 H
Gross weight.
B0
L
1B2 B1
230002 B1 L
B2
H
3B0 B3
430003 B3 H
Net weight.
B0
L
5B2 B1
6
30004
B1
L
B2
H
7B0 B3
830005 B1 - Input Status Register (see Table 1 page 33).
B1
-
9B0 B0
10 30006 B1 - Command Status Register (see Table 3 page 34).
B0
-
11 B0 B1
12 30007 B1 - Output Status Register (see Table 2 page 33).
B0
-
13 B0 B1
14 30008 B1 -Selected page - Data format
(bit 0 to 13) (bit 14 to 15)
0 = uns. integer 01 = sig. integer B0
-
15 B0 10 = float B1
16 30009 B3 H
Gross weight.
B0
L
17 B2 B1
18 30010 B1 L
B2
H
19 B0 B3
20 30011 B3 H
Tare weight.
B0
L
21 B2 B1
22 30012 B1 L
B2
H
23 B0 B3
24 30013 B3 H
ID
B0
L
25 B2 B1
26 30014 B1 L
B2
H
27 B0 B3
28 30015 B1 - Alibi status register
B0
-
29 B0 B1
30 30016 - - Not used. - -
31

© Rice Lake Weighing Systems • All Rights Reserved 11
ADC Value "Page 3000" (0x0BB8)
Byte Modbus TCP
Register Big Endian Dato Little Endian
030001 B3 H
Gross weight.
B0
L
1B2 B1
230002 B1 L
B2
H
3B0 B3
430003 B3 H
Net weight.
B0
L
5B2 B1
630004 B1 L
B2
H
7B0 B3
830005 B1 - Input Status Register (see Table 1 page 33).
B1
-
9B0 B0
10 30006 B1 - Command Status Register (see Table 3 page 34).
B0
-
11 B0 B1
12 30007 B1 - Output Status Register (see Table 2 page 33).
B0
-
13 B0 B1
14 30008 B1 -Selected page - Data format
(bit 0 to 13) (bit 14 to 15)
0 = uns. integer 01 = sig. integer B0
-
15 B0 10 = float B1
16 30009 B3 H
ADC points.
B0
L
17 B2 B1
18 30010 B1 L
B2
H
19 B0 B3
20 30011
- - Not used. - -
... ...
31 30016

12 Visit our website www.RiceLake.com
µV Value "Page 3001" (0x0BB9)
Byte Modbus TCP
Register Big Endian Dato Little Endian
030001 B3 H
Gross weight.
B0
L
1B2 B1
230002 B1 L
B2
H
3B0 B3
430003 B3 H
Net weight.
B0
L
5B2 B1
630004 B1 L
B2
H
7B0 B3
830005 B1 - Input Status Register (see Table 1 page 33).
B1
-
9B0 B0
10 30006 B1 - Command Status Register (see Table 3 page 34).
B0
-
11 B0 B1
12 30007 B1 - Output Status Register (see Table 2 page 33).
B0
-
13 B0 B1
14 30008 B1 -Selected page - Data format
(bit 0 to 13) (bit 14 to 15)
0 = uns. integer 01 = sig. integer B0
-
15 B0 10 = float B1
16 30009 B1 - µV value.
B0
-
17 B0 B1
18 30010
- - Not used. - -
...
31 30016

© Rice Lake Weighing Systems • All Rights Reserved 13
Calibration 0 - Scale Parameters "Page 5000" (0x1388)
Byte Modbus TCP
Register Big Endian Dato Little Endian
030001 B3 H
Gross weight.
B0
L
1B2 B1
230002 B1 L
B2
H
3B0 B3
430003 B3 H
Net weight.
B0
L
5B2 B1
630004 B1 L
B2
H
7B0 B3
830005 B1 - Input Status Register (see Table 1 page 33).
B1
-
9B0 B0
10 30006 B1 - Command Status Register (see Table 3 page 34).
B0
-
11 B0 B1
12 30007 B1 - Output Status Register (see Table 2 page 33).
B0
-
13 B0 B1
14 30008 B1 -Selected page - Data format
(bit 0 to 13) (bit 14 to 15)
0 = uns. integer 01 = sig. integer B0
-
15 B0 10 = float B1
16 30009 B3 - Unit of measure 0 = g 1 = kg B0
L
17 B2 2 = t 3 = lb B1
18 30010 B1 - Range 1 division
B2
H
19 B0 B3
20 30011 B3 - Range 2 division
B0
L
21 B2 B1
22 30012 B1 - Decimals
B2
H
23 B0 B3
24 30013 B3 H
Range 1
B0
L
25 B2 B1
26 30014 B1 L
B2
H
27 B0 B3
28 30015 B3 H
Range 2
B0
L
29 B2 B1
30 30016 B1 L
B2
H
31 B0 B3
To set the data, write the same positions in the output area and use command 36 (0x24) "DATA WRITING AND STORAGE" with
PARAMETER 1 equals to 5000.

14 Visit our website www.RiceLake.com
Calibration 1 - Calibration Points Weights "Page 5001" (0x1389)
Byte Modbus TCP
Register Big Endian Dato Little Endian
030001 B3 H
Gross weight.
B0
L
1B2 B1
230002 B1 L
B2
H
3B0 B3
430003 B3 H
Net weight.
B0
L
5B2 B1
630004 B1 L
B2
H
7B0 B3
830005 B1 - Input Status Register (see Table 1 page 33).
B1
-
9B0 B0
10 30006 B1 - Command Status Register (see Table 3 page 34).
B0
-
11 B0 B1
12 30007 B1 - Output Status Register (see Table 2 page 33).
B0
-
13 B0 B1
14 30008 B1 -Selected page - Data format
(bit 0 to 13) (bit 14 to 15)
0 = uns. integer 01 = sig. integer B0
-
15 B0 10 = float B1
16 30009 B1 - Number of calibration points.
B0
-
17 B0 B1
18 30010 B1 -
Sample weight 1.
B0
L
19 B0 B1
20 30011 B1 -
B2
H
21 B0 B3
22 30012 B1 -
Sample weight 2.
B0
L
23 B0 B1
24
30013
B1
-
B2
H
25 B0 B3
26 30014 B1 -
Sample weight 3.
B0
L
27 B0 B1
28 30015 B1 -
B2
H
29 B0 B3
30 30016 B1 - Calibration state (same as page 5006, only reading)
B0
-
31 B0 B1
To set the data, write the same positions in the output area and use command 36 (0x24) "DATA WRITING AND STORAGE" with
PARAMETER 1 equals to 5001.

© Rice Lake Weighing Systems • All Rights Reserved 15
Calibration 2 - Calibration Points ADC "Page 5002" (0x138A)
Byte Modbus TCP
Register Big Endian Dato Little Endian
030001 B3 H
Gross weight.
B0
L
1B2 B1
230002 B1 L
B2
H
3B0 B3
430003 B3 H
Net weight.
B0
L
5B2 B1
630004 B1 L
B2
H
7B0 B3
830005 B1 - Input Status Register (see Table 1 page 33).
B1
-
9B0 B0
10 30006 B1 - Command Status Register (see Table 3 page 34).
B0
-
11 B0 B1
12 30007 B1 - Output Status Register (see Table 2 page 33).
B0
-
13 B0 B1
14 30008 B1 -Selected page - Data format
(bit 0 to 13) (bit 14 to 15)
0 = uns. integer 01 = sig. integer B0
-
15 B0 10 = float B1
16 30009 B3 H
ADC value of the zero point.
B0
L
17 B2 B1
18 30010 B1 L
B2
H
19 B0 B3
20 30011 B3 H
ADC value of the point 1.
B0
L
21 B2 B1
22 30012 B1 L
B2
H
23 B0 B3
24 30013 B3 H
ADC value of the point 2.
B0
L
25 B2 B1
26 30014 B1 L
B2
H
27 B0 B3
28 30015 B3 H
ADC value of the point 3.
B0
L
29 B2 B1
30 30016 B1 L
B2
H
31 B0 B3
To set the data, write them to the same position in the output area and use command 36 (0x24) "DATA WRITING AND STORAGE" with
PARAMETER 1 equal to 5002.

16 Visit our website www.RiceLake.com
Calibration 3 - Legal State "Page 5003" (0x138B)
Byte Modbus TCP
Register Big Endian Dato Little Endian
030001 B3 H
Gross weight.
B0
L
1B2 B1
230002 B1 L
B2
H
3B0 B3
430003 B3 H
Net weight.
B0
L
5B2 B1
630004 B1 L
B2
H
7B0 B3
830005 B1 - Input Status Register (see Table 1 page 33).
B1
-
9B0 B0
10 30006 B1 - Command Status Register (see Table 3 page 34).
B0
-
11 B0 B1
12 30007 B1 - Output Status Register (see Table 2 page 33).
B0
-
13 B0 B1
14 30008 B1 -Selected page - Data format
(bit 0 to 13) (bit 14 to 15)
0 = uns. integer 01 = sig. integer B0
-
15 B0 10 = float B1
16 30009
- Not used in reading. - -
17
18 30010
19
20
30011
B1
- Pre-calibration state
0 = no. B0
-
21 B0 1 = yes. B1
22 30012 B1 - Setup size
B0
-
23 B0 B1
24 30013 B1 - Restricted 0 = internal use. B0
-
25 B0 1 = restricted. B1
26 30014
- - Not used. - - ... ...
31 30016
To set the data, write the same positions in the output area and use command
36 (0x24) "DATA WRITING AND STORAGE" with
PARAMETER 1 equals to 5003.
The instrument will permanently save the setting and reboot.

© Rice Lake Weighing Systems • All Rights Reserved 17
Calibration 4 - Filter and Metrical Parameters (1/2) "Page 5004" (0x138C)
Byte Modbus TCP
Register Big Endian Dato Little Endian
030001 B3 H
Gross weight.
B0
L
1B2 B1
230002 B1 L
B2
H
3B0 B3
430003 B3 H
Net weight.
B0
L
5B2 B1
630004 B1 L
B2
H
7B0 B3
830005 B1 - Input Status Register (see Table 1 page 33).
B1
-
9B0 B0
10 30006 B1 - Command Status Register (see Table 3 page 34).
B0
-
11 B0 B1
12 30007 B1 - Output Status Register (see Table 2 page 33).
B0
-
13 B0 B1
14 30008 B1 -Selected page - Data format
(bit 0 to 13) (bit 14 to 15)
0 = uns. integer 01 = sig. integer B0
-
15 B0 10 = float B1
16 30009 B1 - Filter index (see Table 5 page 35)
B0
-
17 B0 B1
18 30010 B1 - Rate custom filter.
B0
-
19 B0 B1
20 30011 B1 - Win custom filter.
B0
-
21 B0 B1
22 30012 B1 - Avg custom filter.
B0
-
23 B0 B1
24 30013 B1 - Pit custom filter.
B0
-
25 B0 B1
26 30014 B1 - Auto zero at start-up.
B0
-
27 B0 B1
28 30015 B1 - Auto zero percentage.
B0
-
29 B0 B1
30 30016 B1 - Zero percentage (by key / command)
B0
-
31 B0 B1
To set the data, write the same positions in the output area and use command 36 (0x24) "DATA WRITING AND STORAGE" with
PARAMETER 1 equals to 5004.

18 Visit our website www.RiceLake.com
Calibration 5 - Metrical Parameters (2/2) "Page 5005" (0x138D)
Byte Modbus TCP
Register Big Endian Dato Little Endian
030001 B3 H
Gross weight.
B0
L
1B2 B1
230002 B1 L
B2
H
3B0 B3
430003 B3 H
Net weight.
B0
L
5B2 B1
630004 B1 L
B2
H
7B0 B3
830005 B1 - Input Status Register (see Table 1 page 33).
B1
-
9B0 B0
10 30006 B1 - Command Status Register (see Table 3 page 34).
B0
-
11 B0 B1
12 30007 B1 - Output Status Register (see Table 2 page 33).
B0
-
13 B0 B1
14 30008 B1 -Selected page - Data format
(bit 0 to 13) (bit 14 to 15)
0 = uns. integer 01 = sig. integer B0
-
15 B0 10 = float B1
16 30009 B1 - Zero tracking. (see Table 6 page 35)
B0
-
17 B0 B1
18 30010 B1 - Division for stability. (number of divisions)
B0
-
19 B0 B1
20 30011 B1 - G value of the calibration zone.
G value decimals – 9.7.
B0
-
21 B0 B1
22 30012 B1 - G value of the use zone.
E.g. g=9.80390, the value
displayed will be 10390.
B0
-
23 B0 B1
24 30013 B1 - Zero tracking time. (100-5000ms)
B0
-
25 B0 B1
26 30014 B1 - Stability detection time. (10-10000ms)
B0
-
27 B0 B1
28 30015 B1 -Additional filter for stability
detection. (0-2000ms, 0 disabled)
B0
-
29 B0 B1
30 30016 B1 - Stability detection divisions. (1-100 divisions)
B0
-
31 B0 B1
To set the data, write the same positions in the output area and use command 36 (0x24) "DATA WRITING AND STORAGE" with
PARAMETER 1 equals to 5005.

© Rice Lake Weighing Systems • All Rights Reserved 19
Calibration 6 - Condensed Calibration "Page 5006" (0x138E)
Byte Modbus TCP
Register Big Endian Dato Little Endian
030001 B3 H
Gross weight.
B0
L
1B2 B1
230002 B1 L
B2
H
3B0 B3
430003 B3 H
Net weight.
B0
L
5B2 B1
630004 B1 L
B2
H
7B0 B3
830005 B1 - Input Status Register (see Table 1 page 33).
B1
-
9B0 B0
10 30006 B1 - Command Status Register (see Table 3 page 34).
B0
-
11 B0 B1
12 30007 B1 - Output Status Register (see Table 2 page 34).
B0
-
13 B0 B1
14 30008 B1 -Selected page - Data format
(bit 0 to 13) (bit 14 to 15)
00 = uns. integer 01 = sig. integer B0
-
15 B0 10 = float B1
16 30009 B1 - Unit of measure. 00 = g 01 = kg B0
-
17 B0 10 = t 11 = lb B1
18 30010 B1 - Division.
B0
-
19 B0 B1
20 30011 B1 - Number of decimals.
B0
-
21 B0 B1
22 30012 B3 H
Capacity.
B0
L
23 B2 B1
24 30013 B1 L
B2
H
25 B0 B3
26 30014 B3 H
Sample weight for calibration.
B0
L
27 B2 B1
28 30015 B1 L
B2
H
29 B0 B3
30
30016
B1
-Calibration state
(reading only)
0 (0x00) = Calibration not started.
B0
-
1 (0x01) = Acquisition in progress.
2 (0x02) = Acquistion OK.
3 (0x03) = Acquisition error.
31 B0
4 (0x04) = Calibration OK.
B1
5 (0x05) = Calibration error.
6 (0x06) = Zero calibration in progress.
To set the data, write the same positions in the output area and use command 36 (0x24) "DATA WRITING AND STORAGE" with
PARAMETER 1 equals to 5006.
Automatically will be set:
Division 2 = 0, Range 2 = 0, Number of calibration points = 1, Sample weight 2 = 0, Sample weight 3 = 0, ADC value of the point 2 = 0,
ADC value of the point 3 = 0.

20 Visit our website www.RiceLake.com
Advanced Filters "Page 5007" (0x138F)
Byte Modbus TCP
Register Big Endian Dato Little Endian
030001 B3 H
Gross weight.
B0
L
1B2 B1
230002 B1 L
B2
H
3B0 B3
430003 B3 H
Net weight.
B0
L
5B2 B1
630004 B1 L
B2
H
7B0 B3
830005 B1 - Input Status Register (see Table 1 page 33).
B1
-
9B0 B0
10 30006 B1 - Command Status Register (see Table 3 page 34).
B0
-
11 B0 B1
12 30007 B1 - Output Status Register (see Table 2 page 33).
B0
-
13 B0 B1
14 30008 B1 -Selected page - Data format
(bit 0 to 13) (bit 14 to 15)
0 = uns. integer 01 = sig. integer B0
-
15 B0 10 = float B1
16 30009 B1 - Filter 1 ID.
B0
-
17 B0 B1
18 30010 B1 - Filter 1 value.
B0
-
19 B0 B1
20 30011 B1 - Filter 2 ID.
B0
-
21 B0 B1
22 30012 B1 - Filter 2 value.
B0
-
23 B0 B1
24 30013 B1 Filter 3 ID.
B0
-
25 B0 B1
26 30014 B1 Filter 3 value.
B0
-
27 B0 B1
28 30015
- - Not used. - -
...
31 30016
ID Filter type Value
0- Filter disabled.
1Coarse Frequency, 1 decimal (the value 30 stands for 3,0 Hz)
4Selective Frequency, 1 decimal (the value 500 stands for 50,0 Hz)
5Fine Percentage, 2 decimal (the value 100 stands for 10%)
To set the data, write the same positions in the output area and use command
36 (0x24) "DATA WRITING AND STORAGE" with
PARAMETER 1 equals to 5007.