Right Weigh 202-DDG-03 User manual

ONBOARD LOAD SCALE
INTERIOR DIGITAL |202-DDG-03

WELCOME
2
Thank you for choosing to drive more and scale less! Here at Right
Weigh, we are commied to making our products simple to install
and easy to use. We understand that installaon can vary between
vehicles and yours may not be described in this manual. In any
event, our technical support team is ready to answer your
quesons!
[phone]
[phone] - Toll Free (USA ONLY)
[phone] - Australia & New Zealand
[email protected]
[email protected] - Australia & New Zealand
www.rwls.com/how-to-calibrate-install/
rightweigh.com.au - Australia & New Zealand
FOLLOW US!
IMPORTANT!
Please read instrucons COMPLETELY and thoroughly before installaon.
Right Weigh, Inc. is not responsible or liable for product failure or vehicle
damage due to improper installaon. The installaon requirements are
outlined in this manual and should be followed thoroughly to avoid inaccuracy
or damage to the product.
It is also important to be aware of vehicle manufacturer policies before making
modificaons to the vehicle. Right Weigh, Inc. is not liable or responsible for
issues regarding warranes with other manufacturers. This is the responsibility
of the customer. If you are unsure about how these installaon pracces apply
to your vehicle, please contact your vehicle or component manufacturer.

Specificaons & Overview
Scale Installaon & Electrical Connecons
Air Sensor Configuraon
Changing Air Sensor Names
Esmated Steer Mode
Units / Display Sengs
Calibraon
Operang & Weighing
Seng Security PIN Code
Reset Calibraon Data
Factory Default
Troubleshoong
Appendix A - Addional Parts (Tractor Suspension Installaon)
Appendix B - Addional Parts (Trailer Suspension Installaon)
Warranty Statement
Return Policy & Repairs
4
6
9
11
12
13
14
17
18
19
20
21
23
24
26
27
CONTENTS
3

The Right Weigh 202-DDG-03 digital load scale has three internal air pressure
sensors. This scale can monitor either:
• one axle group with two HCVs + one axle group with one HCV
• three separate axle groups with one HCV each
1 HCV1 HCV
2 HCVs
SPECIFICATIONS & OVERVIEW
4
The weight of the steer axle can be esmated if this scale is used to monitor
the drive axle group. Refer to the Esmated Steer Mode secon for more
informaon.
Esmated Steer Axle:
Example of one axle group with one HCV and one axle group with two
HCVs:
Example of three axle groups with one HCV each:
1 HCV
1 HCV

Technical Specificaons
Operang Temperature: -4° F to +185° F (-20° C to +85° C)
Storage Temperature: -4° F to +185° F (-20° C to +85° C)
Power Requirement: 9 VDC to 32 VDC (Switched)
Units: Pounds (LBS) or Kilograms (KG)
Housing: ABS/PC Blend
Display: Capacitave Touch
SPECIFICATIONS & OVERVIEW
5
63 mm
2.5”
60mm
2.4”
15 mm
0.6”
65 mm
2.6”
51mm
2.0”

SCALE INSTALLATION
& ELECTRICAL CONNECTIONS
6
CHOOSE MOUNTING LOCATION
1
The gauge can be mounted in the dash panel either using an exisng factory
gauge hole or by creang one. If this opon is unavailable or not desirable,
Right Weigh has an oponal bracket (202-BR) that can be purchased
separately to mount the gauge. See below for a detailed list of opons for
mounng into the dash:
The 202-DDG-03 scale is designed to be mounted inside the vehicle cabin, it is
not for outdoor use. The following steps will walk you through how to correctly
mount and install the gauge.
Use an available 2 1/16”(52mm) factory
gauge hole.
a
Remove and replace a factory installed
drive axle air suspension pressure
gauge.
b
Cut a new hole in the dash panel using a
2 1/16” (52mm) hole saw as shown.
c
Make sure to check behind the dash
panel for internal wires and
components that may need to be
moved to avoid damage.
!
Use Right Weigh 202-BR bracket or an aermarket bracket to
mount the gauge.
d

7
SCALE INSTALLATION
& ELECTRICAL CONNECTIONS
CONNECT TO POWER AND GROUND
4
Connect the wiring harness to power and
ground. Be sure the RED wire is connected to
a SWITCHED posive (+) power source (DO
NOT CONNECT DIRECTLY TO BATTERY) and
the BLACK wire to chassis ground (-). Supply
voltage must be between 9 and 32 volts DC.
DO NOT connect directly to a battery or any constant power
source, gauge should be connected to a switched source so
that it can be disconnected from power when not in use. Most
users connect the power to the ignition switch.
!
INSERT 202 GAUGE
2
Insert the gauge into the mounng
hole or bracket. Hold the gauge in a
posion so the display appears level
on the dash panel or bracket. Note
that the thickest poron of the gauge
bezel indicates the boom of the
display. Screw the gauge nut onto the
back of the gauge unl it is ght.
TIGHTEN
INSERT
Connect the wire harness
to the connector on the
back of the gauge.
DUMP AIR FROM SUSPENSION SYSTEM
5
INSTALL BEZEL STYLING
COVER (OPTIONAL)
3
If desired, place chrome styling cover
over the front of the gauge bezel.
Press unl both sides snap into place.

8
SCALE INSTALLATION
& ELECTRICAL CONNECTIONS
REPEAT STEPS 5-8 FOR SECOND AND
THIRD HCVS OR AXLE GROUPS
9
ROUTE AIR LINE TO GAUGE
8
Route the new 1/4” air line from the
tee fing assembly to the gauge.
Secure air line with zip es. Insert the
air line into the push-to-connect
fing on the back of the gauge.
RE-ASSEMBLE DASH PANEL IF NEEDED
11
AIR UP SUSPENSION TO CHECK FOR LEAKS
10
INSTALL NEW STREET TEE FITTING
6
Install a new 1/4” air line and fing into
the remaining port on the tee.
Air Bag
Air Bag
Street tee
fitting
Insert suspension air line
and fitting into the tee fitting
Insert new air line and
fitting into the tee fitting
Remove suspension
air line and fitting
Air Bag
Insert a street tee fing into the top of the
air bag that matches the thread size of the
vehicle suspension. Reinstall the suspension
air line and fing into the street tee. For
more informaon on the parts needed for air
line installaon, see Appendix A (gauge to
tractor suspension) and Appendix B (gauge
to trailer suspension).
7 INSTALL NEW 1/4” AIR LINE
Remove the suspension air line fing from
the top of one of the air bags connected to
the first axle group being monitored.
If monitoring an axle group with two Height Control Valves
(HCVs), connect the two air lines from that group to air sensors 1
and 2 as marked on the back of the gauge.
!

AIR SENSOR CONFIGURATION
9
The 202-DDG-03 gauge can be used to monitor up to three separate axle groups
with one Height Control Valve (HCV) each, or a combinaon of axle groups with a
total of three HCVs. Follow the steps below to configure the gauge to your
applicaon:
Home
Weight
System Setup
Calibration
Settings
Settings
Units
Display Settings
Settings
Config Names
From the Home screen, select the
WRENCH icon.
From the System Setup screen, select
SETTINGS.
From the Sengs screen, select
the RIGHT ARROW and then
select USER CONFIG. Then
select the right arrow to
connue to the next screen.
Config Inputs
Settings
User Config
Average All
Sensor Mode
Select CONFIG INPUTS.

10
AIR SENSOR CONFIGURATION
Config Inputs
If monitoring an axle group with two HCVs, the two air sensors connected to that
axle group must be set to Average together. For any axle groups with one HCV, the
sensor for that group must be set to be Independent from the rest. To set the desired
configuraon, select the blue buons between the numbers (air sensors 1, 2, and 3)
unl each is set correctly for your applicaon.
12
= Average
= Independent
3
Example: Air sensors 1
and 2 are averaged and
sensor 3 is independent
Config Inputs
1 2
3
Example: All air sensors
are measured
independently from one
another
If monitoring an axle group with two HCVs, the air lines from this
group MUST be connected to sensors 1 and 2 or sensors 1 and 3
so they can be averaged together. Sensors 2 and 3 CANNOT be
averaged together.
!

CHANGING AIR SENSOR NAMES
11
The default sengs for the gauge can be changed to make the informaon
specific to your vehicle configuraon. To change the default air sensor name,
follow these steps:
Home
Weight
System Setup
Calibration
Settings
Settings
Units
Display Settings
Settings
Config Names
Config Names
1:
Drive
Config Names
Steer Drive
Trailer A Trailer B
From the Home screen, select the
WRENCH icon.
From the System Setup screen, select
SETTINGS.
From the Sengs screen, select
the RIGHT ARROW twice and
then select CONFIG NAMES.
Press the first sensor or sensor group to
change the name.
Select the appropriate name from the list.
Press the RIGHT ARROW for more
opons.
2:
Trailer A
Repeat the process for each addional axle group.
3:
Trailer B
Config Inputs

12
ESTIMATED STEER
If the 202-DDG-03 load scale is used to monitor a tractor’s drive axle group, the
Esmated Steer opon can be enabled. Esmated Steer will not work for straight
trucks or anyone who slides their fih wheel regularly. To enable Esmated Steer,
follow these steps:
Home
Weight
System Setup
Calibration
Settings
Settings
Units
Display Settings
Settings
Est. Steer
Est. Steer
On
From the Home screen, select the
WRENCH icon.
From the System Setup screen, select
SETTINGS.
From the Sengs screen, select
the RIGHT ARROW three
mes and then select EST.
STEER.
To turn on Esmated Steer, make sure the
“ON” buon is selected as shown.
Language
Off

UNITS / DISPLAY SETTINGS
13
Home
Weight
System Setup
Calibration
Settings
Settings
Units
Display Settings
Units
From the Home
screen, select the
WRENCH icon.
From the System Setup
screen, select
SETTINGS.
The gauge can be set to read in ENGLISH
(LBS) or METRIC (KG). Make sure the
buon is selected next to the units sengs
desired.
Use the slider to adjust the backlight.
CHANGING UNITS
DISPLAY SETTINGS
From the Sengs
screen select either
UNITS or DISPLAY
SETTINGS.
English
Metric
Display Settings
Backlight

The 202-DDG-03 load scale must be calibrated both empty and loaded to
work properly. The scale associates the air pressure in the suspension
system to the weight you enter at the me of calibraon. You will need to
calibrate once while the vehicle is empty, and again while the vehicle is
loaded for the axle group(s) being monitored.
STEER AXLE
(Esmated) DRIVE AXLE
GROUP
(2 HCVs)
TRAILER AXLE
GROUP
Only enter on-the-ground weight of axle or group being
monitored. DO NOT use gross weight, tare weight, etc.
!
Follow calibraon steps on the next page, once these are complete the gauge
will be ready to use!
CALIBRATION
14
STEER AXLE
(Esmated) DRIVE AXLE
GROUP TRAILER A
AXLE GROUP TRAILER B
AXLE GROUP

CALIBRATION
15
1. While the vehicle is empty, obtain axle group weights from a cerfied
in-ground scale.
2. Park on a level surface. Shi the transmission to neutral and set the
parking brakes. Chock the wheels to prevent unexpected vehicle movement,
then release the parking and service brakes.
3. Make sure the Height Control Valve (HCV) has fully inflated the air bags. If
needed, briefly dump the air from the suspension and allow the HCV to refill
the system.
EMPTY CALIBRATION POINT
Home
Weight
System Setup
Calibration
Settings
Calibration
Est. Steer
Drive
4. From the Home screen, select the
WRENCH icon.
5. From the System Setup screen, select
CALIBRATION.
6. From the Calibraon screen select
the appropriate axle group. For more
opons, press the RIGHT ARROW.
Cal. Est. Steer Axle
Empty
Loaded
7. From the Calibraon
screen select EMPTY. Select
YES to enter new calibraon
data.
Continue?
Do you want to
enter new
calibration
data?
Yes No
123
4
7
5 6
8 9
Del 0 Enter
8. Enter weight from scale
cket for the corresponding
axle group and then press
ENTER.
If the value you have
entered looks correct, select
YES to save calibraon data.
10,800 Continue?
Set 10,800lb as
Est. Steer
Empty
calibration value?
Yes No
9. Repeat process for all axle groups being monitored, including steer
axle if using Esmated Steer feature.

CALIBRATION
16
LOADED CALIBRATION POINT
Repeat “empty calibraon point” steps 1-3 with the vehicle
fully loaded
Home
Weight
System Setup
Calibration
Settings
Calibration
Est. Steer
Drive
4. From the Home screen, select the
WRENCH icon.
5. From the System Setup screen, select
CALIBRATION.
6. From the Calibraon screen select
the appropriate axle group.
For more opons, press the RIGHT
ARROW.
Cal. Est. Steer Axle
Empty
Loaded
7. From the Calibraon
screen select LOADED.
Select YES to enter new
calibraon data.
Continue?
Do you want to
enter new
calibration
data?
Yes No
123
4
7
5 6
8 9
Del 0 Enter
8. Enter weight from scale
cket for the corresponding
axle group and then press
ENTER.
If the value you have
entered looks correct, select
YES to save calibraon data.
11,460 Continue?
Set 11,460lb as
Est. Steer
Loaded
calibration value?
Yes No
9. Repeat process for all axle groups being monitored, including steer
axle if using Esmated Steer feature.

OPERATING & WEIGHING
17
Follow these steps while weighing your vehicle:
1: Park on a level surface. Shi the transmission to neutral and set the
parking brakes.
2: Chock the wheels to prevent unexpected vehicle movement, then release
the parking and service brakes.
3: Make sure the Height Control Valve (HCV) has fully inflated the air bags. If
needed, briefly dump the air from the suspension and allow the HCV to refill
the system. (This may take several minutes depending on the type of HCV.)
Home
Weight
4. From the Home screen, select
WEIGHT.
Summary
Est. Steer
Drive
Total
11,200
31,600
108,720
5. From the Summary screen, you
can view the weight of the axle
groups being monitored, the
esmated steer weight (if this
feature is turned on), and the total
weight.
6. From the summary screen, you can select the RIGHT ARROW to view each
weight separately and the net weight.
Est. Steer
11,200
Drive
31,600
Net
0
ZERO
By selecng ZERO, the
net weight will reset to
0. This reading will
display the net change
in total weight since
the last me the ZERO
buon was pressed.
If the screen says “Cal Needed”
then further calibraon needs
to be performed on one or more
axle groups.
!
Cal
Needed
Press the HOME buon at any me to return to the Home screen.
33,800
32,120
Trailer A
Trailer B

SECURITY PIN CODE
18
Home
Weight
System Setup
Calibration
Settings
Calibration
Est. Steer
Drive
From the Home screen, select the
WRENCH icon.
From the System Setup screen, select
CALIBRATION.
From the Calibraon screen
select the RIGHT ARROW
and then select SET PIN.
To protect calibraon data from unwanted changes, you can set a security PIN
code. When a PIN is set, the user will be required to enter the PIN in order to get
into the calibraon screens. Follow these steps to set a PIN code:
Calibration
Set PIN
Reset Cal Data
123
4
7
5 6
8 9
Del 0 Enter
Enter a unique PIN code (up to 6 digits).
If a PIN code is forgoen or lost, please contact Right
Weigh technical support listed on page 2 for instrucons
on how to reset the PIN code.
!

19
RESET CALIBRATION DATA
Home
Weight
System Setup
Calibration
Settings
Calibration
Est. Steer
Drive
From the Home screen, select the
WRENCH icon.
From the System Setup screen, select
CALIBRATION.
From the Calibraon screen
select the RIGHT ARROW
and then select RESET CAL
DATA.
In rare cases, it might be necessary to reset the calibraon data back to the
original default values. To reset the calibraon data to the default values, follow
these steps:
Calibration
Set PIN
Reset Cal Data
Reset Cal Data
YES to reset.
NO to cancel.
Yes No
To reset the calibraon back to the default
values (erase any previous calibraon data)
select YES.

FACTORY DEFAULT
20
Home
Weight
System Setup
Calibration
Settings
Calibration
Est. Steer
Drive
From the Home screen, select the
WRENCH icon.
From the System Setup screen, select
CALIBRATION.
From the Calibraon screen
select the RIGHT ARROW
twice and then select
FACTORY DEFAULTS.
If there is a problem with the gauge, it may be necessary to reset it completely
back to factory default sengs. This will remove previously set calibraon data,
air sensor configuraon and names, PIN code, etc. To reset the gauge, follow
these steps:
Calibration
Factory Defaults
Factory Defaults
YES to reset.
NO to canel.
Yes No
To reset the gauge back to the factory
default sengs, select YES.