RIKA VISIO Guide

Die Seele Ihres Heimes
RIKA-KAMINÖFEN
MANUAL
VISIO

2
Fig. 2
Fig. 1
Exhaust gas connection
Combustion air connection

3
Fig. 4
Fig. 3

4
Fig. 5

5
A Bus 1
B Bus 2
C Bus 3
a Fine-wire fuse
b Capacitor
Fig. 6
Fig. 7
1 HAL-RG-Fan
2 Control board
3 Remote-fixed network
4 Air sensor
5 UTB
6 OTB
7 FKY 1
8 FKY 2
9 Alarm
I Network 230VAC 50Hz
II RG-Fan
III Cross flow fan
IV Ignition element
V Auger motor
VI Circulating pump
VII Reserve
MAIN CONTROL BOARD
123456789VII VI VIV III II I
yellow/green
blue
brown
PE
N
L
a
b
PE yellow/green
ABC

7. OPERATION
6.FITTING OPTIONS
4.AUTOMATIC SAFET FUNCTIONS
1. IMPORTANT INFORMATION
TABLE OF CONTENTS
5.INSTALLING THE ENCLOSED FIRE
6
2.WHAT ARE PELLETS?
3.TECHNOLOG
ENGLISH
Overview of technical data and spare parts 8
General warning and safety instructions 9
Pellet storage 9
Operating comfort - Operating security 10
Highest efficiency - Lowest emissions 10
Power failure 10
Overheating 10
Low temperature switch off 10
Electric excess current cut out 10
Genral information 11
Making the flue connection 11
Method 11
Floor protection 11
Safety distances 11
Electrical connection 12
Combustion air 12
Feeding external combustion air 12
General 13
Fitting the steel or ceramic front cladding,
ceramic lid with insert 13
Fitting convection fan (optional) 13
Basic information 14
Control and internal control unit - function 14
Internal control unit 14
Possible operating ranges 14/16
Using the heater for the first time 16
Stopping the heater 16/17
External control unit with room temperature probe
(Pellet-Control-Optional) 17

7
EXPLANATION OF S MBOLS
Important instructions
Practical advice
Use the fold out plan for assistance
10. FAULT FINDING AND SOLUTIONS
9.MAINTENANCE AND CLEANING
12. GUARANTEE
ENGLISH
11. APPENDIX
8.ELECTRONIC IGNITION
Heating up without electric ignition 18
Some field values 18
Adding fuel 18
Basic information 19
Operating handle 19
Wood as fertiliser 19
Cleaning the fire grate 19
Cleaning the fire door 19
Cleaning the exhaust air flues 19/20
Cleaning the exhaust air manifold 20/21
Cleaning the exhaust air fan housing 21
Cleaning the pellet container 21
Inspecting the door seal 21
Checking the chimney connection 21
Cleaning the air sensor 21
Problems - Causes - Possible Solutions 22/23
Menu driven operation for programming the internal control 24
We guarantee 27
Guarantee card 27/28

8
TECHNICAL DATA
(Fig. 1)
The owner of the pellet heater is required
to retain the technical documentation and
to present it on demand for inspection by
the authorities or the chimney sweep.
PACKAGING
Your first impression is important tous!
- The packaging of your new domestic
heater offers excellent protection against
damage. Nevertheless, damage can occur to
the heater and the accessories during trans-
portation.
Therefore please check your heater on receipt
to ensure it is complete and free from damage!
Inform your dealer of any shortfalls without
delay!
The wood in the packaging is not surface
treated and can therefore be burnt in your
pellet heater.
The cardboard and sheeting (PE) can be
disposed of at public refuse disposal facilities
for re-cycling.
- The packaging used for your domestic
heater is mainly environmentally neutral.
SPARE PARTS - O ER IEW
(Fig. 3 - Fig. 7)
DESCRIPTION
01 Fire door
02 Fire door seal
03 Fire door glass
04 Upper temperature limiter
05 Ignition element
06 Conveyorscrew complete
07 Centring plate
08 Motor plate
09 Hexagonal bolt
10 Conveyor screw drive motor
11 Air sensor
20 Internal control unit
21 Main fuse
22 Main board
23 Remote fixed network board (optional)
30 Wing nut
31 Flue gas shaft cleaning lid
32 Intermediate bottom
33 Top/bottom cleaning lid
34 Exhaust gas fan housing
35 Exhaust gas fan motor
36 Hexagonal screws
37 Low temperature switch
38 Smoke tube adapter 100 mm
39 Fire door hinge
40 Container lid (with rating plate, warning sign)
41 Rear wall
42 Side cladding rear right complete
43 Rear wall cover
44 Mains cable with earthed plug
45 Corner post front right complete
46 Front cladding bottom
47 Front cladding top
48 Corner post front left complete
49 Side cladding rear left complete
50 Ceramic lid with insert
TECHNICAL DATA
eight
Width
Depth
Weight without casing
Weight with steel front
Weight with ceramic front
Smoke tube pipe diameter
eating performance range
Room heating capacity (m3)
dependent on house insulation
Fuel consumption
Pellet container capacity
Power supply
Average electrical power consumption
Fuse
1031
530
600
130
137
142
100
2,4 - 8
50 - 220
0,6 - 1,8
32
230; 50
< 100
1,6 T
Exhaust air mass flow
Exhaust air temperature
Chimney draft requirement
6.0 - 6.0
157 - 229
0 - 0
[mm]
[mm]
[mm]
[daN]
[daN]
[daN]
[mm]
[kW]
[m3]
[kg/h]
[kg]
[V]; [ z]
[W]
[A]
[g/s]
[°C]
[Pa]
Subject to technical and optical modifications as well as typographical errors and misprints.
ENGLISH

1. IMPORTANT INFORMATION
GENERAL WARNING AND
SAFETY INSTRUCTIONS
The introductory general warning and
safety instructions must be unconditio-
nally observed
➧Read the whole manual thoroughly be-
fore using the fire for the first time.
➧Only approved transport aids with ade-
quate carrying capacity may be used to
transport the heating device.
➧Yourheating device isnotsuitable for use
as a ladder or to stand on.
➧Burning fuels releases heat energy that
leads to the surface of the pellet heater, as
well as the doors, the door and operating
handles, the door glass, the smoke tubes
and occasionally the front wall of the hea-
ting device heating up.
Thermal value: 5.3 kWh/kg
Density: 700 kg/m
3
Water content: max. 8% of the weight
Ash content: max. 1% of the weight
Diameter: 5 - 6.5 mm
Length: max. 30 mm
Contents: 100 % wood, untreated and without
any binding agent (proportion of bark
max. 5%)
Packaging: in sacks made from environmentally
friendly or biologically degradable
plastic or from paper (2 - 3 layer/
similar to cement packaging)
Do not touch these parts without the rele-
vant protectiveclothingoraidssuchas heat
protective gloves or operating materials
(cold hand).
➧Ensure that children are aware of this
particular danger and keep them away
from the heating device during operation.
➧Do not place non-heat resistant items on
the heating device or in its vicinity.
➧Do not put washing on the fire to dry.
➧Stands for drying items of clothing or
suchlike must be set up at an adequate
distance from the heating device - fire
hazard!
➧Processing easily inflammable or explo-
sive substances in the same of adjoining
rooms isprohibitedwhenthe heatingdevice
is in operation.
PELLET STORAGE
The fuel must be stored as dry as possible
in order to guarantee problem free burning
of the wood pellets.
9
2. WHAT ARE PELLETS?
Pellets are made from wood waste from
saw- and planing mills as well as brash from
forestry operations. These „starting pro-
ducts“ are crushed, dried and pressed into
„fuel“ pellets without any binding agent.
Please request the tested fuel and a list of
monitored fuel producers from your pellet fire
consultant.
Using poor quality or prohibited pellet fuel
influences the function of your fire and can
further lead to the guarantee and the product
liability becoming invalid.
SPECIFICATIONS FOR HIGH QUALITY
PELLETS:
ENGLISH

The advanced technological state of your
pellet fire is the result of years of tests in
laboratory and practice.
The practical advantages of your pellet
fire are convincing:
OPERATING COMFORT -
OPERATING SECURITY
The fire is controlled by a digital electronic
monitoring device together with a patented
„air sensor“ that controls the interaction of
a flue gas fan, worm conveyor, convection
fan and temperature monitoring.
This monitoring system guarantees an opti-
mum combustion and operating state.
Operation is reduced to a minimum - this
means no operating errors with optimum
operation at the same time.
HIGHEST EFFICIENCY -
LOWEST EMISSIONS
Averylargeheatexchangersurfacetogether
with an optimum combustion air control
results in very good use of fuel.
Finely dosed pellet feed in an optimised
burner pot made from high quality cast
steel results in almost perfect combustion
withvery goodexhaust gasvalues-and that
is guaranteed in every phase of operation.
10
3. TECHNOLOG
4. AUTOMATIC SAFET FUNCTIONS
POWER FAILURE
After a brief power failure the operating
functions that were set before the power
failure are continued.
ON-mode (manual operation): The control
switches into ST (start phase) and the de-
vicethen continues torun in ON-operation.
TM-mode (automatic operation): The contol
switches into ST (start phase) and the de-
vice then continues to run in TM-operation.
SB-mode (Standby-operation): The control
switches into SB operation after approx. 2
seconds.
Some smoke can be emitted when the
power fails. This does not last any longer
than three to five minutes and is not a safety
risk.
OVERHEATING
An excess temperature switch (OTB) swit-
ches the heater off automatically in the
caseofoverheating.Afterthefirehascooled
down it returns to the control programme.
However whether heating operation is
continued depends on the embers still in
the combustion pan. If no ignition takes
place when fuel feed is started again, then
the shutdown programme (cleaning, after-
running phase) is carried out. The fire must
be started again dependent on the pre-set
mode.
LOW TEMPERATURE SWITCH OFF
The fire switches off if it cools down below
a minimum temperature.
It can also switch off if starting takes too
long.
ELECTRIC EXCESS CURRENT CUT OUT
The fire is fitted with a main fuse (on the
rear of the fire) as protection against excess
current (Data as per Item 1)
ENGLISH
CAUTION! If the fire overheats it is imperative
that maintenance and cleaning work is carried
out.

5. INSTALLING THE ENCLOSED FIRE
GENERAL INFORMATION
The fire must be connected to a chimney
that has been approved for solid fuel. The
chimney must have a diameter of at least
120 mm.
The flue gas system is based on underpres-
sure in the combustion chamber and a light
excess pressure on the flue gas outlet. It is
therefore important that the flue gas con-
nection is fitted correctly and in an airtight
manner.
Only use heat resistant sealing materials, as
well as heat resistant silicon and mineral wool.
MAKING THE FLUE CONNECTION
(Fig. 1)
Method
1. Measure out and mark the fire connec-
tion (taking any floor plate thickness into
consideration) (Fig. 1)
2. Chisel out (drill) the hole in the wall
3. Seal in wall lining
4.Connect fire with the smoke tube to the
chimney
FLOOR PROTECTION
The fire must be installed on a fire resi-
stance surface. A fire resistant underlay
(steel plate, ceramic or similar) is required
for flammable floors (wood, carpet etc.).
Minimum dimensions for a relevant
underlay (floor plate):
From the fire chamber opening to the
front:
50 cm
From the fire chamber opening to the left
and right:
30 cm (each side)
SAFETY DISTANCES
(Fig. 2)
(Measured from the outside surface of
the fire)
11
We recommend that only the authorised specia-
list company carries out fitting (or inspection
and approval in the case of own installation).
Please also ensure that the smoke tube
does not jut out into the free cross section
in the chimney.
ATTENTION! Please follow locally valid building
regulations.
Contact your chimney sweep for information on
this.
Avoid extraction routes to the chimney
that are too long.
Avoid too many changes in the direction of
the exhaust gas flow to the fire (e.g. too
many corners and bends).
Should you not be able to connect directly
to the fire, then use a connecting piece
with cleaning opening if possible.
1. To non flammable items
a > 400 mm b > 100 mm c > 100 mm
2. To flammable items and to supporting walls made
of reinforced concrete
a > 800 mm b > 200 mm c > 200 mm
When the exhaust pipe is not connected
horizontally (e.g. leading upwards) keep the
safety distance to the pipe of 10 cm.
ENGLISH

90˚ end end wind hood
minimum diameter 5 cm/2“
wall
150
wall
50
70
ELECTRICAL CONNECTION
The fire is supplied with an approx. 2.5 m
long connecting cable with Euro plug.
Connect this cable to a 230 volt, 50 Hz
electrical connection. The average electri-
cal power consumption during heating is
approx. 100 watt. During the automatic
ignition process (duration approx. 10
minutes) itisapprox.350watt. Theconnec-
tion cable must be laid so that any type of
contact with the hot or sharp edged
exterior surfaces of the fire is avoided.
COMBUSTION AIR
Each combustion processrequiresoxygenor
air. Thiscombustionairisusually drawnfrom
the living area for single fires.
This air that has been withdrawn must be
fed into the living room again. It is possible
inmodern housesthatnotenoughair flows
in through very tightly sealed windows and
doors. This situation is also problematic
due to additional ventilation in the house
(e.g. in the kitchen or WC).
12
Feeding External Combustion Air
➧Only use steel pipes
➧Minimum diameter, 5 cm/2 inches
➧Pipesmade fromplasticoraluminiumare
not permitted!
➧The line should be no longer than
approx. 4 m to guarantee adequate air feed
and not have too many bends.
➧If the line leads into the open air it must
end with a downward vertical 90˚ bend or
with a windbreaker (see sketch).
Should one or more of these conditions be
applicable this gives rise to poor combus-
tion in the fire as well as an air vacuum in
the house.
We recommend that an air grid be fitted in
a window near the fire for permanent ven-
tilation.
It is further possible to draw the combus-
tion air directly from outside or from anot-
her room with adequate ventilation (e.g.
cellar).
ENGLISH

GENERAL
ATTENTION! Only carry out any work on the
fire when the mains plug has been removed.
13
6. FITTING OPTIONS
When fitting do not allow any items (screws
etc.) to drop into the fuel container - they
can block the conveyor screw and damage
the fire.
The fire must be switched off and have cooled
down before work can be carried out.
ENGLISH
FITTING THE STEEL OR CERAMIC
FRONT CLADDING, CERAMIC LID
WITH INSERT
(Fig. 6)
1. Open both corner posts (Fig. 6, Part 45
and 48) by slackening the hexagonal
bolts at the top on the front corner post
bracket.
2. Hang the bottom front cladding (Fig. 6,
Part 46) in the edges of the cleaning
door. The bottom brackets centre the
front cladding in the centre of the fire.
3. Upper front cladding: First remove both
hexagonal screws in the front of the
frame (next to the corner post fixing
screws). Now hang the upper front clad-
ding (Fig. 6, Part 47) in the recess in the
frame and fix it using the previously
removed hexagonal screws.
4.Now carefully let the corner post snap
intothebottomspring steel clipand fix it
intheupper area again usingthehexago-
nal screws as per Item 1.
5. Open the pellet container lid (Fig. 6, Part
40). Align the ceramic lid on the pellet
fire using the insert (Fig. 6, Part 50).
The round recesses in the bottom must
be positioned on the outer hexagonal
screws in the front frame.
CAUTION! The corner posts have been snapped
in a spring steel clip at the bottom - open by
pulling accordingly.
FITTING THE CONVECTION FAN
(OPTIONAL)
(Fig. 6)
Remove the rear side panels (Fig. 6, Part 42)
on the left and right by removing the hexa-
gonal screws at the top front and rear on
the rear panel. Pay attention to the feed for
the internal control unit when doing this.
Nut
Picture 1
Using the 2 nuts supplied fasten the con-
vection fan on the screws provided in the
combustion chamber rear panel (Fig. 1), by
inserting the washer under the nut.
Nut
Picture 2 Convection fan plug
Lay the power line in the mounts on the
control board casing and insert the 2-pole
plug in Position III.
Now fit the rear side panels on the left and
right side again.
CAUTION! The convection fan must only be
fitted by an authorised specialist.

7. OPERATION
IT IS VITAL T AT T E FIRE PAINTWORK IS
BAKED OUT.
Please follow the following advice when using
the fire for the first few times:
- No children are allowed in the room whilst
this is taking place, as vapours escaping
could be a danger to health.
Adults should also avoid staying in the room
for a longer period of time.
- Do not touch the surface during heating as
it is still soft.
- Ventilate the house several times to remove
the vapours that have been released.
- eat the fire up to hot - this shortens the
heating and hardening time.
- ardening the surface is completed after
several heating procedures.
14
The fire must only be started when fully fitted.
Your pellet fire is exclusively approved for
burning pellets made from controlled quality
wood.
Burning non pelletised solid fuels (straw,
maize etc.) is not allowed. Failure to comply
with these specifications invalidates all gua-
rantees and could influence the security of
the fire.
When your pellet fire is operated correctly it
cannot overheat. owever continuous heating
at high capacity can shorten the life expec-
tancy of the fire components (fan, motors
and electric control) and is not recommended.
BASIC INFORMATION
ENGLISH
CONTROL AND INTERNAL
CONTROL UNIT - FUNCTION
(Fig. 4, Part 20)
The pellet fire is fitted with a modern pro-
grammable microprocessor control.
The user can preset the individual device
functions via the Internal Control Unit
fitted on the rear right side panel (keypad
with operating display).
Adjustments to the control (main board)
and on the control board may only be car-
ried out by a trained specialist or the ser-
vice personnel.
Inappropriate handling of these parts will
lead to loss of guarantee.
Internal Control Unit
All settings and functions can be controlled
via this unit.
Illustr. 1: Internal control unit Key assign-
ment
DISPLAY FIELD:
Displays the operating states in illuminated
letters.
MENU:
Navigation in the menu level
ENTER:
Navigation in the normal display, in the sub-
menus, confirming entries
MINUS/PLUS:
Reducing or increasing values
ON/OFF:
Switching the fire on or off.
See the APPENDIX, page 24) for a graphic
image of the menu drive for the program-
ming levels.
Possible operating ranges
Your pellet fire can be preset in 3 different
operating modes.
➧Manual operation
➧Automatic
➧Standby-mode
Selecting „ENTER“ enables you to change
between the individual operating types.
„MENU“ key
„MINUS“ key
„ON/OFF“ key
Display field
„ENTER“ key
„PLUS“ key

Manual operation
There is no display when the fire is swit-
chedoff.Pushingthe ON/OFF buttonswit-
ches the fire on and the display is activated.
Thedisplayin theupper linejumpsto„ON“
and the fire goes into start phase „ST“ at
the same time. This phase is shown by
alternating display (flashing) „ST“/“ON“.
The bottom line changes between display-
ing the heating output set as a percentage
or the remaining start time in increments
of a minute.
Heating output display: „100“ is the rated
thermal output. „0“ is the lowest heating
capacity. The heating capacity is adjusted
5% increments using the +/- key in.
Start time display: „21“ is the start time in
minutes.
Display on concluding the start phase:
Top: „ON“
Bottom: e.g. „50“ (heating capacity in %).
Automatic operation with
programming the heating time
It is recommended that the weekday pro-
gramming described in the following is car-
ried out after the start programme has
been completed.
Pushing the „ENTER“ key switches over
from „Manual Operation“ (display „ON“) to
time controlled heating. The display „TM“
(TIME) will appear in the upper line and the
current heating capacity in percent in the
bottom line. 2 on or off times can be pro-
grammed per weekday. One heating capa-
city can be programmed for the heating or
lowering times.
In general it applies: If you want to keep a
selection, then select the next display stage
using „ENTER“.
Weekday programming:
Change over into the weekday program-
ming by pushing the „MENU“ key - „MO“
(Monday) appears, pushing the „ENTER“
key willdisplay „E1“(switch ontime1) atthe
top and atthe bottom thetime in hours(0 -
23 hrs). The +, - keys can be used to alter
the time in increments of one hour. Using
„ENTER“ confirm the selection you have
made and the program will display „A1“
(switch off time 1) with the respective time.
The value can be altered as described pre-
viously. Now „E2“ appears with the time
etc. After confirming the „A2“ value using
„ENTER“, the weekday „MO“ (Monday)
appears again. Selecting „MENU“ displays
the weekday „DI“ (Tuesday). Continue with
the programming of the switch on and
switch off times for the further weekdays
as described above.
Programming the Heating Capacity,
Cleaning Cycle:
When all weekdays „MO“, „DI“, „MI“, „DO“,
„FR“, „SA“ and „SO“ have been programm-
ed, selecting „MENU“ in the display shows
„LE“ (output during switch on time) at the
top, with the display at the bottom as e.g.
„75“ (heating capacity in percent). This
valuecan be altered in 5%increments using
the +/- buttons - the new value is confir-
med using „ENTER“ and the display show
„LA“ (output when switched off) at the top
with the display at the bottom showing e.g.
„10“ (heating capacity in %). This value can
be altered in 5% increments again using the
+/-keys–the new valueis confirmed using
„ENTER“. The value for „LA“ in these hea-
ting times can either be lowered as given
above or switched off by pushing the „-“
several times and the display will show
„OFF“at thebottom (i.e. the fire isswitched
off between the heating times).
ENGLISH
15

ENGLISH
After the „LA“ value has been confirmed
using „ENTER“, the „RZ“ (Cleaning Cycle)
value is shown with the value in minutes
(lower display). The value can be altered in
increments of one minute using the +/-
keys. (When the prescribed fuel is used, we
recommend that the cleaning run is carried
out every 60 minutes). The value for the
„RZ“ is confirmed using „ENTER“ and selec-
ting „MENU“ the display will show the time
programming „ZH“.
Time programming:
The top display shows „ZH“ (internal clock
hour memory) and the bottom display
shows the value in hours. The +/- key is
used to alter the value, confirm using
„ENTER“ and „ZM“ (internal clock minute
memory) then appears. Alter the minute
value using +/-, pressing „ENTER“ displays
„WT“ (weekday, MO=1, DI=1 -› SO=7), +/-
alters the value. Selecting „MENU“ displays
„RI“.
Tele-Control
(optional telephone triggering):
This function is not part of the standard
display and can be retrofitted if required.
The relevant additional device functions
and the programming of the system values
are included in the retrofitting kit.
Standby-Mode:
The fire is switched off in this operating
mode but remains active to receive tele-
phone triggering. The display shows „SB“.
Starting the fire for the first time
General remarks
➧Check that the pellet container is full and
the combustion chamber is clean and
free from ash.
After filling the storage tank and plugging
the fire in, the start programme is carried
out by pressing the „ON/OFF“ button on
the internal control unit. The fire carries
out the „Manual operating mode“ (see
Manual Operation, page 15).
You can now select the operating modes as
per the Possible Operating Ranges Item
(Page 14) in accordance with your require-
ments.
Stopping the fire
Switching off from „Manual Operation“
If the „ON/OFF“ button is pushed during
operation, then all functions will continue
to run (without the conveying worm), so
long until the fire has cooled down suffi-
ciently and the following alternating infor-
mation appears on the display (in an appro-
ximately 2 second cycle):
a) ON manual operation with xx%
heating output
b) VZ delay phase of xxx seconds
c) CL clear (cleaning phase) of xxx
seconds
d) NL after running of xxx seconds
(The whole switch off procedure will take
approximately 7 seconds)
After theswitch offprogrammehasfinished
thedisplay goesout. A newstartthen takes
place by pushing the „ON/Off“ button.
CAUTION! The combustion chamber door must
be closed during the ignition procedure. The
electric ignition will not work if the combustion
chamber door is open.
When the pellet container is opened for the
first time, no pellets are transported into the
fire pan. You can put a handful of pellets in
the combustion pan to prevent the fire from
restarting again.
16

ENGLISH
Switching the fire
out of automatic running
(timed operation or manual)
If the „LA“ output is switched to „OFF“
when the fire is switched off (see Heating
Output, Cleaning Cycle Programming,
Page 15), then when in timed operation the
fire is switched off as described in the func-
tions above. The display flashes the follo-
wing alternately:
a) TM Time with xx% heating output or
b) to d) remain identical
After completing the switch off procedure
the display will show the following:
TM Time with OFF
The fire is reactivated after a new start
phase has been completed, as soon as the
next programmed heating period begins.
Ifthe„ON/OFF“ keyispushedduring auto-
matic operation, the fire will immediately
go into the shutdown run. The display
flashes alternately:
a) TM Time with xx% heating output or
b) to d) remain the same
After the shutdown phase is complete the
display will show the following:
TM Time with OFF
The fire is reactivated by running through a
new start phase, as soon as the next pro-
grammed heating period begins.
aSwitching off using the operating mode
change in standby
Change from „Manual Operation“ as well
as from Automatic into Standby Mode by
pressing „ENTER“, this switches the fire off
using the procedure described above. After
completing the switch off programme the
display shows „SB“.
To restart the relevant mode must be
selected or the fire started using the re-
mote function (Telephone Start).
External control unit
with room temperature probe
(Pellet-Control-Optional)
The external control unit can be used to
extend your Pellet Fire with Room
Temperature Control Function. To do this
the room temperature is measured using a
sensor in the external control unit.
This function is not part of the standard
scope of supply and can be retrofitted if
required. The relevant extended functions
of the fire and the programming of the
system values are included in the retrofit-
ting kit.
17

8. ELECTRONIC IGNITION
ENGLISH
18
HEATING UP WITHOUT
ELECTRIC IGNITION
➧CAUTION! ONLY APPLIES TO FIRES
WIT OUT ELECTRIC IGNITION.
➧If your fire has an electric ignition and this
is faulty - please contact the Service
Department or Repair Service!
If your pellet fire does not have electric
ignition, then please proceed as follows:
1. Check whether the pellet container is
filled and the combustion chamber is
clean and free from impurities. Place
approved fire lighters in the cavity and
lay a small handful of pellets on the top.
Please note: Do not use inflammable
liquids for starting the fire!
2. Light the firelighters in the fire pan with
a match and close the fire door carefully.
Push the „ON/OFF“ key. This setting will
run the start procedure.
20 kg of pellets should be sufficient for
approx.12 hoursoperationat„max.“ setting
or approx. 40 hours at „min.“ setting.
(Different pellet fuel can give rise to devia-
tions to the above!)
Please consult your authorised pellet fire
dealer if there are any questions.
We recommend that the storage container
is kept topped up to prevent the fire from
goingout duetolackoffuel. Assoon asthe
pellet container is less than half full, a 15 kg
pellet sack can be tipped into your pellet
fire. Check the filling level often. However
the container lid should always be closed
except during filling.
Pellet container capacity (see Technical
Data)
CAUTION when filling! Do not let the pellet
sack touch the hot fire! Remove any pellets
that have not dropped into the storage con-
tainer immediately!
FUEL FEED
The pellet fire is fitted with an electric ig-
nition.
This begins to function along with the start
programme.
Ignition start duration: Approx. 12 mins
CAUTION! Always wear heat resistant gloves
when filling the storage container!
Pellet consumption is dependent on the size of
the pellets. The larger the pellets the slower
the feed and vice versa.
The pellet fire can be run continuously with-
out hesitation and without risk, however it is
recommended that the heating capacity be
reduced over night and when leaving the room
for longer periods of time.
SOME PRACTICAL INFORMATION

9. MAINTENANCE AND CLEANING
19
ENGLISH
BASIC INFORMATION
Your fire must be switched off and have cooled
down before carrying out maintenance.
The frequency with which your fire is to be
cleaned as well as maintenance intervals
depends on the fuel used.
High moisture content, ash, dust and chips
can more than double the required mainte-
nance intervals. We would therefore like to
point out once more that only tested and
approved wood pellets may be used as fuel.
Operating Handle
An operating handle is supplied with your
new pellet fire this is for opening or closing
the fire door. Please use this operating
handle for:
➧Cleaning the fire grate
➧Loosening the pellets in the container,
should they stick on the side walls.
Wood as Fertiliser
Approx. 1 - 2 % of wood minerals remain
as ash after burning. This ash is a natural
product and an excellent fertiliser for all
plants in the garden. However the ash
should be stored and „extinguished“ with
water beforehand.
Please take care: The ash may contain
embers, only put into metal containers.
ATTENTION! Only start maintenance when the
fire mains plug has been removed from the
socket.
CLEANING THE FIRE DOOR
The best way to clean the fire door glass is
with a damp cloth. Persistent dirt can be
removed with a special cleaning material
that can be purchased from your fire dealer.
CLEANING THE EXHAUST AIR FLUES
The flue gas channels are situated at the
side of the fire chamber (Picture 3).
➧Remove the ceramic lid (Fig. 6, Part 50)
from the fire. Open the combustion
chamber door.
➧Remove the wing nut (Fig. 5, Part 30) and
lift the flue gas shaft cleaning lid off (Fig.
5, Part 31). Do this on the left and right
hand side of the fire.
➧Clean the heating gas flues on the com-
bustion chamber side using the soot
brush (Fig. 6).
➧Remove the topmost combustion cham-
ber lid (Fig. 5, Part 33) by unscrewing the
4 wing nuts.
➧Now vacuum the exposed interior cham-
ber and the side apertures clean from
soiling.
➧Fit the parts in reverse order.
Picture 3
CLEANING THE FIRE GRATE
(Picture 2)
Check the fire grate to ensure that the air
feed openings are not blocked by ash or
clinker. The fire grate is easy to clean inside
the fire. The area underneath it can be
cleaned after the grate has been removed.

20
Picture 4
ENGLISH
Picture 5
Clean flue gas channels
Picture 6
CLEANING THE EXHAUST
AIR MANIFOLD
The heating gas manifold is located in the
bottom area of the combustion chamber
(Picture 7 to Picture 10).
➧After removing the front claddings (see
Page 13)
➧Opening the combustion chamber door
➧Remove the bottom inspection opening
(Fig. 5, Part 33) (4 wing nuts)
➧Clean the interim bottom (Fig. 5, Part 32)
(e.g. using a vacuum cleaner) and then
remove from the combustion chamber.
➧Now remove the combustion residue
from the collection channel with a
vacuum cleaner.
➧Fit the parts again in reverse order.
Ensure that seals are tight.
Picture 7
Picture 8
Picture 9