Rinnai JZY-11S User manual

OPERATING INSTRUCTIONS
使用說明書使用說明書
型號型號 MODEL JZ (Y,T)-11S
型號型號 MODEL RB-11S-C
CERAMIC GLASS TOP BUILT-IN HOB
嵌入式陶瓷玻璃檯面平面爐嵌入式陶瓷玻璃檯面平面爐
NAGOYA JAPAN
CORPORATION
RB-11S-C(NEW).indd 1RB-11S-C(NEW).indd 1 3/18/2009 2:55:49 PM3/18/2009 2:55:49 PM

– 1 –
In order to obtain the best results and to maintain your Built-In Hob in the best condition, lease read the
instructions below carefully:
為確保爐具正確使用及維持最佳效能 , 請詳閱以下說明 :
COMPONENTS AND PARTS NAMES 各部份名稱及組成
Pan Su ort
爐架
Burner Head-S
爐頭-S
Burner Body
爐體
Dri Pan
爐碟
To Plate
面板
Casing
爐身
Burner Head-H
爐頭-H
Front Side
前面
Gas Inlet
燃氣管連接部
Battery 1.5V × 1 Size C
乾電池 1.5伏特 × 1 C 型
Sealing Packing
密封圈
RB-11S-C(NEW).indd Sec1:1RB-11S-C(NEW).indd Sec1:1 3/18/2009 2:55:51 PM3/18/2009 2:55:51 PM

– 2 –
SPECIFICATION 規格
Heat In ut 輸入熱量 :
Gas Inlet Connection : Ø9.5 Hose End
燃氣入口接駁 : Ø9.5 毫米接駁口
Overall Dimensions : Height 高 74.5 mm 毫米 (To To Plate 至爐面)
55 mm 毫米 (To Bench To 至櫥檯面)
整體尺寸 95 mm 毫米 (To Pan Su ort 至爐架)
: Width 寬 310 mm 毫米
: De th 深 521.5 mm 毫米 (Body 爐身)
Weight 重量 : 6.0kg 千克
BENCHTOP CUT-OUT DIMENSIONS 櫃面開孔尺寸
INSTALLATION 安裝
* Install the built-in hob in a well ventilated room and kee it away from any combustible or infl ammable
objects such as a er or oil.
爐具須安裝在空氣流通之房間內 , 附近不可放置易燃物品如紙張、油類等。
* Place the built-in hob on a stable and level bench to . Please refer to Fig. 2 for cut-out dimensions and
osition.
爐具須放置在穩固及水平的櫃面上 , 請依照圖 2 所示的開孔尺寸及位置。
50mm (MIN)
268mm
600mm (MIN)
490mm
Case by non-infl
ammable wall
在有隔火墙的情況下
High Calorifi c Value
高發熱量
Low Calorifi c Value
低發熱量
L. P. G. 4.0 kW 3.5 kW
N. G. 5.4 kW 4.5 kW
RB-11S-C(NEW).indd Sec1:2RB-11S-C(NEW).indd Sec1:2 3/18/2009 2:55:51 PM3/18/2009 2:55:51 PM

– 3 –
* If another built-in a liance (e.g. dishwasher, washer, etc,) is to be installed under the built-in hob, kee a
clearance of at least 10mm from the bottom of the built-in hob. If the installation of the a liance underneath
requires a different distance, ado t the larger value.
若在嵌入式平面爐下安裝其他器具 ( 如洗碗碟機 , 洗衣機等 ) 。 請保留最少 10 毫米的距離。
若其他器具的安裝指引要求不同的間距 , 應採用較大者。
* The built-in hob should be installed with a distance of more than 15cm away from surrounding combustible
materials.
此爐具的安裝位置應與週圍易燃物料距離 15 厘米以上。
* If the built-in hob is to be installed on to of a built-in oven, a artition between two a liances is required
with all ga s being sealed. It is to avoid the infl uence of air draught on the o eration of the built-in hob when
the oven fan is running.
煮食爐下方如設有嵌入式焗爐 , 必須加裝隔層板並將所有縫隙密封 , 避免焗爐的風機氣流影響煮食
爐運作。
* In case utting artition late under a liance, stand a art from a liance by over 10cm.
若要將隔層板安裝在器具下，站架需與器具隔開 10 釐米以上。
* Make sure that the following arts are fi tted ro erly before use:
使用前請確定以下配件已置於正確位置 :
1. Pan Su ort 爐架
Fit Pan Su ort into Glass To Plate.
爐架正確地安放於玻璃面板上。
Install the hollow art behind the trivet nail
art at the two oints of convex side of the to
late ro erly.
將凹入部分穩當地安裝在頂面板凸面上的
兩點的三腳火爐架尖頭部分後
2. Burner Head, Burner Body 爐頭 , 爐體
Set back holes of Burner Body with Electrode Fixing lace. Then insert Burner Head Pin to to holes of
Burner Body.
將爐體後的開孔對準點火針安裝位置。然後將爐頭腳插入爐體面上的插孔。
Fit Burner Head into Burner Body ro erly without ga . See the right illustration as below.
爐頭放置在爐體上 , 放置時請勿傾斜。 如下圖。
Burner Head-S
爐頭 -
S
S ark Electrode
點火針
Burner Head-H
爐頭 -
H
Safety Sensor
安全感應頭
Pan Su ort De ression
爐架凹部
Dri Pan Projection
爐碟凸部
Ga
空隙
Ga
空隙
RB-11S-C(NEW).indd Sec1:3RB-11S-C(NEW).indd Sec1:3 3/18/2009 2:55:51 PM3/18/2009 2:55:51 PM

– 4 –
INSTRUCTIONS FOR USE 操作要點
ATTENTION! 注意 !
This built-in hob is to be used for cooking only. Do not dry towels, clothes, etc. over it.
此爐具只用於烹飪 , 不可用於烘乾衣物、毛巾等。
1. While ushing the Control Knob, turn it to the left (toward the “ON” osition) slowly until you hear a ‘click’
sound. Electronic s ark will ignite burners.
Kee ushing the Control Knob for a few seconds after the burner is ignited (Safety Device will then
o erate).
If you release the knob halfway, electronic s ark might not be able to ignite burners.
請一邊按住爐具開關爐掣一邊向左 ( 開的方向 ) 慢慢地旋轉。
“ ”隨著 啪、啪 的響聲 , 火花將點燃燃燒器。在確認燃燒器被點燃後數秒鐘內 , 請保持原位置
（安全裝置啟動）。
如果中途放開手，可能點不著火。
2. If the fl ame goes out when you release your hand from the knob, re eat the ignition rocedures, kee
ushing the Control Knob for a longer time and release your hand more slowly than last time.
若手放開爐具開關掣而火仍未點著時，請用同樣的方法再次操作，將按爐掣的時間保持長久一
些，然後將手慢慢地放開。
3. Turn Control Knob to adjust fl ame to desirable setting.
轉動爐掣， 調節爐火至所需火力。
4. Flame can be adjusted between “MAX” and “OFF”. Please adjust fl ame slowly.
“ ” “ ”火力強弱可在 最大 和 熄火 之間調校。請緩慢調校火力。
5. Turn the ignition Control Knob backwards to the “OFF” osition to extinguish the fl ame.
“ ”將爐掣轉回至熄火 位置，爐火便會熄滅。
* The Safety Sensor is delicate, lease do not use stiff brushes or rough cleaning ads when cleaning.
防漏熄火安全感應頭十分精密 , 不可用粗 的刷子或其他東西進行清潔。
* Aeration is reset at manufacturing, lease do not attem t to adjust it.
廠方已調校了風位 , 不可自行嘗試調校。
* Please do not use Aluminium Mat. Use of aluminium mat may cause combustion roblem.
請勿使用錫紙碟。使用錫紙碟可能會引致爐頭燃燒不正常。
Outside fl ame
外環火 : Max. 最大
Inside fl ame
內環火 : Max. 最大
Outside fl ame
外環火 : Off 熄滅
Inside fl ame
內環火 : Max. 最大
Outside fl ame
外環火 : Off 熄滅
Inside fl ame
內環火 : Min. 最弱
Outside fl ame
外環火 : Middle 中火
Inside fl ame
內環火 : Middle 中火
RB-11S-C(NEW).indd Sec1:4RB-11S-C(NEW).indd Sec1:4 3/18/2009 2:55:52 PM3/18/2009 2:55:52 PM

– 5 –
HANDLING PROCEDURES WHEN FLAME FAILURE SAFETY DEVICE OPERATES
防漏熄火安全裝置生效時的處理方法
If the fl ame is extinguished during o eration, the automatic Flame Failure Safety Device will shut the gas off
after a short delay.
If you notice that the fl ame has been extinguished, lease turn the knob to the “OFF” osition.
如爐頭在使用中火焰突然熄滅 , 防漏熄火安全裝置會自動切斷氣供應。
如察覺火焰熄滅 , 請將爐掣轉至「熄火」位置。
CHANGE BATTERY 更換電池
* Battery Box is located at bottom of center front (Size C, 1.5V × 1) (Fig. 6)
電池盒在爐身的底部中前方 (C 型 ,
1.5伏特 × 1) ( 圖6)
* Set battery correctly according to ⊕ .
請小心別把乾電池的⊕ 弄錯。
MAINTENANCE 維修
* Wi e the to late with a soft dam cloth, and mild detergent.
用乾淨, 柔軟抹布及洗潔精清潔爐面。
* Wash the an su orts and burners with warm water and detergent.
用暖水及洗潔精清理爐架及爐頭。
* Use the neutral detergent since the burner body made by aluminium.
(Please do not use alkaline.)
使用中性洗潔精 , 以防止鋁質爐體被侵蝕。
( 請勿使用鹼性的洗潔精 )
* Please clean with an acutemetal as below design when the burner hole
is cloged with s ill over.
請用尖銳的金屬棒清除被溢瀉物堵塞的爐頭孔。
Burner Body-H (aluminium)
爐體 -
H(鋁)
Burner holes
爐頭孔
Front Side
前面
RB-11S-C(NEW).indd Sec1:5RB-11S-C(NEW).indd Sec1:5 3/18/2009 2:55:52 PM3/18/2009 2:55:52 PM

– 6 –
CAUTION 注意
* Glass to late is fixed. Do not remove it.
玻璃面是固定的 ! 切勿移動。
* Pan su ort is heavy. Do not dro it.
爐架是很重的 ! 切勿掉下。
* Do not clean the glass when the a liance is hot.
當爐具熱時 , 請勿清洗玻璃。
* Do not lace hot cooking utensil on the glass surface.
請勿將熱的煮食器皿放在玻璃上。
TROUBLE SHOOTING MANUAL FOR BUILT-IN HOB
嵌入式雙頭爐的故障檢查手冊
Fault 故障 Cause 原因Remedy 處理方法
1. No Ignition
點火不著
S ark electrode is wet es ecially
in seasons of high humidity.
點火電極(瓦咀 )濕了 ,尤其是在
潮濕季節。
Dry the electrode with tissue or
dry cloth.
以紙巾或乾毛巾抹乾點火電極
(瓦咀 ) 。
2. Flame cannot be held
不能保持火焰
Incorrect turning of gas control
knob.
不正確轉動爐掣。
Push and turn the gas control
knob anti-clockwise until a ‘click’
sound is heard. Hold for a few
seconds fl ame is ignited.
推入爐掣及反時針方向旋轉至
「開」位置 , 直至聽到「的」
聲。當爐火點著時 , 按著爐掣
數秒才放手。
3. No main fl ame
爐頭沒有火
3.1 Gas meter cock and/or
a liance cock have been
turned off.
仍未開啟氣錶控制閥及/ 或
爐具切斷閥。
O en gas meter cock and/
or a liance isolating cock
com letely.
完全開啟氣錶控制閥及/ 或爐
具切斷閥。
3.2 Burner head is blocked by
aluminium foil.
錫紙阻塞爐頭。
Remove aluminium foil.
拿去錫紙。
4. Yellow fl ame
黃火
Accumulated grease and dirt on
head.
爐頭積聚油漬和污垢。
Wash burner head in warm water
with detergent. Dry it and lace it
back at correct osition.
以暖水和洗潔精清洗爐頭。把
它抹乾 , 然後放好。
5. Unstable fl ame
火焰不穩定
Incorrect location of burner head.
爐頭未放好。
Refi t burner head into burner body.
重新放好爐頭。
RB-11S-C(NEW).indd Sec1:6RB-11S-C(NEW).indd Sec1:6 3/18/2009 2:55:53 PM3/18/2009 2:55:53 PM

CORPORATION
2-26 Fukuzumi Nakagawa
Nagoya Ja an
TRJB11S-32X01(00)
06000005267470
Printed in Ja an
RB-11S-C(NEW).indd Sec1:7RB-11S-C(NEW).indd Sec1:7 3/18/2009 2:55:53 PM3/18/2009 2:55:53 PM