Rinnai RB-3311S-GBS User manual

1
Instructions for use, installation,
and connection
Gas Built in Hob
RB-3311S-GBS
RB-3312S-GBS
RB-3311D-GBS
RB-3311M-GBS
RB-3311N-GBS
RB-6313S-GBST
RB-6323S-GBST
RB-6314S-GBS
RB-6313D-GBST
RB-6313M-GBST
RB-7312S-GBS
RB-7313S-GBST
RB-7323S-GBST
RB-7314S-GBS
RB-7315S-GBS
RB-7313D-GBST
RB-7312M-GBS
RB-7313M-GBST
RB-7312N-GBS
RB-9312S-GBS
RB-9313S-GBST
RB-9314S-GBS
RB-9315S-GBS
RB-9312D-GBS
RB-9213D-GBST
RB-9314D-GBS
RB-9315D-GBS
RB-9312M-GBS
RB-9313M-GBST
RB-9312N-GBS
RB-9313N-GBSU

2
1. Important Warnings........................................................ 3
2. Safety Instructions.......................................................... 4
3. Line up............................................................................ 6
4. Components and Parts name ........................................ 7
5. Installation ...................................................................... 8
6. Operating Instructions.................................................. 12
7. Maintenance................................................................. 13
8. Trouble Shootings ........................................................ 17
9. Technical Specifications............................................... 18
Thank-you very much for purchasing Rinnai Gas Built in Hob.
More than 90 years of history of introducing high qualified Japan-
designed appliances throughout the world.
Every time you use Rinnai appliances, Rinnai believes you can feel
comfort by its safety and quality.
In order to maximize the performance and to maintain your Rinnai built-
in hob in the best condition, please follow the instruction carefully.
Please visit www.rinnai.com for further inquires
Contents

3
Before installing and using of Rinnai
appliances, carefully read and follow the
supplied instructions. The manufacturer
is not responsible for any damages
caused by incorrect installation and use.
This instruction shall always be kept with
the appliance for future reference and
pass them on to possible new owners of
the appliance.
1.1 General
• Theapplianceanditsaccessibleparts
become hot during use.
• Unattendedcookingonahobwithfat
or oil can be dangerous and may result
in fire. Never try to extinguish a fire
with water, but switch off the appliance
and then cover flame e.g. with a lid or
a fire blanket.
• Theapplianceisnotintendedtobe
operated by means of an external timer
or separate remote control system.
• Donotstoreitemsonthecooking
surfaces.
• Donotuseasteamcleanertoclean
the appliance.
1.2 Children and vulnerable people
WARNING!
Risk of suffocation, injury or
permanent disability.
• Thisappliancecanbeusedby
children aged from 8 years and above
and persons with reduced physical,
sensory or mental capabilities or lack
of experience and knowledge if they
are supervised by an adult or a person
who is responsible for their safety.
• Neverletchildrenplaywiththe
appliance.
• Keepallpackagingmaterialoutofthe
reach from children.
• Keepchildrenandpetsawayfromthe
appliance when it operates or when it
cools down.
• Neverletchildrencleanand
maintenance without supervision.
1. Important Warnings

4
2.1 Installation
WARNING!
Only a qualified person must install
this appliance.
•Removeallthepackaging.
•Neverinstalloruseadamaged
appliance.
•Theminimumdistanceshallbekept
from the other appliances and units as
instructed.
•Alwayswearsafetyglovesandbe
careful when you move the appliances.
•Protectthebottomoftheappliance
from any steam and moisture.
•Preventingfromtheappliancetofall,
never install the appliance adjacent to
a door or under a window.
•Sufficientspacesareneedsforair
circulation when the appliance is
installed above drawers.
Gas connection
•Allgasconnectionsmustbemadeby
a qualified person.
•Confirmsufficientaircirculationaround
the appliance.
•Alwaysconnecttheappliance
according to the latest installation
regulations.
2.2 Use
WARNING!
Risk of burns.
•
CAUTION: The use of a gas cooking
appliance results in the production
of heat, moisture and products of
combustion in the room in which it
is installed. Ensure that the kitchen
is well ventilated especially when
the appliance is in use : keep natural
ventilation holes open or install
a mechanical ventilation device
(mechanical extractor hood).
•
CAUTION : This appliances is for
cooking purposes only. It must not be
used for other purposes, for example
room heating.
•Thisapplianceisintendedforusein
household.
•Neverchangethespecificationofthis
appliance.
•Donotlettheappliancestay
unattended during operation.
•Ensurethecookingzoneto“off”after
cooking.
WARNING!
Risk of fire or explosion.
•Fatsandoilwhenheatedcanrelease
flammablevapors.Keepflamesor
heated objects away from fats and oils
when you cook with them.
•Thevaporsofhotoilreleasesmay
cause spontaneous combustion.
•Usedoilmaycausefireatalower
temperature.
•Neverplaceflammableproductsor
items near or on the appliance.
WARNING!
Risk of damage to the appliance.
•Donotplaceandkeephotcookware
on the control panel.
•Donotignitetheflameswithempty
cookware or without cookware.
•Becarefulnottoletobjectsor
cookware fall on the appliance. The
glass top plate can be damaged.
•Donotplacealuminumfoilonthe
appliance.
•Neveruseunstablecookwarewiththe
incorrect shape and diameter larger
than the dimensions of the burners.
•Makesuretheflamedoesnotgoout
when you quickly turn the knob from
the maximum to the minimum position.
2. Safety Instructions

5
•Makesurecookwareiscentrally
positioned on the pan supports and do
not stick out over edges of the cooking
surface.
•Onlyapplytheaccessoriessuppliedby
manufacturer.
•Neverinstallaflamediffuseronthe
burner.
2.3 Care and Cleaning
WARNING!
Risk of damage to the appliance.
•Cleanregularlytheappliancetoprevent
the deterioration of the surface material.
•Donotusesteamtocleanthe
appliance.
•Neverusethedishwashertocleanthe
burners in the dishwasher.
•Cleantheappliancewithamoistsoft
cloth, and only use neutral detergents.
Never use abrasive products, abrasive
cleaning pads, solvents or metal
objects.
•CAUTION: In case of hotplate glass
breakage:
- Shut immediately off all burners and
any electrical heating element and
isolate the appliance from the power
supply.
- Do not touch the appliance surface,
- Do not use the appliance
2.4 Caution for the tempered glass
•Neveruseoversized
cooking utensils or
overload the cooking
appliances.
•Donotremovethepan
support and enclose the
burner with a wok stand as
this will concentrate and
deflect the heat onto the
gas hob.
•Donotplacethebuilt-
in hob pan over the pan
support side as it can
cause tumbling.
•Useonlyawoksupport
supplied or recommended
by the manufacture of the
appliance.
• Donotplaceanything,e.g.,
flame tamer, asbestos mat
between pan and support
as serious damage to
appliance may result.
2.5 Disposal
WARNING!
Risk of injury or suffocation.
•Pleasecontactyournearmunicipal
authority for detailed information on the
disposal of appliance.

6
3. Line up
30cm Models
Top Plate Dimension ; 310 mm × 520 mm
Cut-Out Hole Dimension ; 268 mm × 490 mm × R0 mm ~ R50 mm
RB-3311N-GBS
InnerFlame
RB-3311M-GBS
Mega
RB-3311D-GBS
Double Simmer
RB-3311S-GBS
Simmer
RB-3312S-GBS
Simmer
60cm Models
Top Plate Dimension ; 620 mm × 520 mm
Cut-Out Hole Dimension ; 560 mm × 480 mm × R0 mm ~ R50 mm
RB-6313M-GBST
Mega
RB-6313D-GBST
Double Simmer
RB-6313S-GBST
Simmer
RB-6323S-GBST
Simmer
RB-6314S-GBS
Simmer
75cm Models
Top Plate Dimension ; 770 mm × 520 mm
Cut-Out Hole Dimension ; 725 mm × 480 mm × R0 mm ~ R50 mm
RB-7312N-GBS
InnerFlame
RB-7312M-GBS
Mega
RB-7313M-GBST
Mega
RB-7313D-GBST
Double Simmer
RB-7312S-GBS
Simmer
RB-7313S-GBST
Simmer
RB-7323S-GBST
Simmer
RB-7314S-GBS
Simmer
RB-7315S-GBS
Simmer
90cm Models
Top Plate Dimension ; 880 mm × 520 mm
Cut-Out Hole Dimension ; 830 mm × 470 mm × R0 mm ~ R100 mm
RB-9312N-GBS
InnerFlame
RB-9313N-GBSU
InnerFlame
RB-9312M-GBS
Mega
RB-9313M-GBST
Mega
RB-9312D-GBS
Double Simmer
RB-9313D-GBST
Double Simmer
RB-9314D-GBS
Double Simmer
RB-9315D-GBS
Double Simmer
RB-9312S-GBS
Simmer
RB-9313S-GBST
Simmer
RB-9314S-GBS
Simmer
RB-9315S-GBS
Simmer

7
4. Components and Parts name
Rinnai Original Burner Series
Inner Flame Series Mega Series Double Simmer Series Simmer Series
Parts Names
Inner Flame Series Mega Series
Double Simmer Series Simmer Series
Pan Support H
Simmer
Burner Head
Burner Head H
Burner Body H
Casing
Knob Tempered Glass
Top Plate
Burner Body S
Burner Head S
Pan Support
Center
Pan Support H
Simmer Burner
Cap
Burner Cap H
Burner Body H
Burner Cover H
Casing
Knob Tempered Glass
Top Plate
Burner Body S
Burner Cover S
Small Burner
Cap
Pan Support S
Pan Support
Burner Head S
Burner Head H
Burner cover
Drip Pan
Drip Pan Seal Packing
Burner S
Top Burner HS
Tempered Glass
Top Plate
Knob
Casing
Pan Support S
Burner Cover S
Drip Pan S
Pan Support H
Drip Pan
Burner Cover H
Tempered Glass
Top Plate
Knob
Casing

8
5. Installation
Kitchen worktop cut-out dimensions
Model Cut out hole dimension (mm)
30 cm
RB-3311S-GBS
RB-3312S-GBS
RB-3311D-GBS
RB-3311M-GBS
RB-3311N-GBS
268 x 490
R0~R50
60 cm
RB-6313S-GBST
RB-6323S-GBST
RB-6314S-GBS
RB-6313D-GBST
RB-6313M-GBST
560 x 480
R0~R50
75 cm
RB-7312S-GBS
RB-7313S-GBST
RB-7323S-GBST
RB-7314S-GBS
RB-7315S-GBS
RB-7313D-GBST
RB-7312M-GBS
RB-7313M-GBST
RB-7312N-GBS
725 x 480
R0~R50
90 cm
RB-9312S-GBS
RB-9313S-GBST
RB-9314S-GBS
RB-9315S-GBS
RB-9312D-GBS
RB-9213D-GBST
RB-9314D-GBS
RB-9315D-GBS
RB-9312M-GBS
RB-9313M-GBST
RB-9312N-GBS
RB-9313N-GBSU
830 x 470
R0~R100
R0~R50
268
490
65
600 (MIN)
R0~R50
560
480
65
600 (MIN)
R0~R50
725
480
65
600 (MIN)
R0~R100
830
470
65
600 (MIN)

9
WARNING!
* Install the built-in hob in a well ventilated room and keep it away from any combustible
or flammable objects such as paper or oil.
* Place the built-in hob on a stable and level surface.
* If the built-in hob is to be installed close to combustible objects (such as wooden walls,
wooden shelves), it should be installed at least 15 cm from the side walls. Even if the
combustible material is protected by stainless steel sheet, a clearance of 15 cm must be
maintained too. If the surrounding material is fireproof, 15 cm clearance is not required.
The clearance between the appliance and above combustible shelves or the ceiling
must be at least 100 cm.
*(ForMegaburnerseriesonly)Iftheovenisinstalledunderneathofhob,itismandatory
to install the separator in between. The separator must be made out of incombustible
material (eg. metal or plywood).
●If the separator is placed underneath of the hob, its distance shall be recommended to be kept more
than 150mm away from the surface of kitchen worktop. Please refer to below diagram.
● Adjustscrewpositionasbenchcutoutsize.
●Confirm that four screws are secured firmly into the casing.
Table Casing Screw
150
1000 (min)
150 (min)
150 (min) 150 (min)

10
●Set the battery properly as instructed.
Model Ignition
Battery Size Battery holder location
30 cm
RB-3311S-GBS C (1.5V × 1)
RB-3312S-GBS C (1.5V × 1)
RB-3311D-GBS C (1.5V × 1)
RB-3311M-GBS C (1.5V × 1)
RB-3311N-GBS C (1.5V × 1)
60 cm
RB-6313S-GBST C (1.5V × 1)
RB-6323S-GBST C (1.5V × 1)
RB-6314S-GBS D (1.5V × 2)
RB-6313D-GBST C (1.5V × 1)
RB-6313M-GBST C (1.5V × 1)
75 cm
RB-7312S-GBS C (1.5V × 1)
RB-7313S-GBST C (1.5V × 1)
RB-7323S-GBST C (1.5V × 1)
RB-7314S-GBS D (1.5V × 2)
RB-7315S-GBS D (1.5V × 2)
RB-7313D-GBST C (1.5V × 1)
RB-7312M-GBS C (1.5V × 1)
RB-7313M-GBST C (1.5V × 1)
RB-7312N-GBS C (1.5V × 1)
90 cm
RB-9312S-GBS C (1.5V × 1)
RB-9313S-GBST C (1.5V × 1)
RB-9314S-GBS D (1.5V × 2)
RB-9315S-GBS D (1.5V × 2)
RB-9312D-GBS C (1.5V × 1)
RB-9213D-GBST C (1.5V × 1)
RB-9314D-GBS D (1.5V × 2)
RB-9315D-GBS D (1.5V × 2)
RB-9312M-GBS C (1.5V × 1)
RB-9313M-GBST C (1.5V × 1)
RB-9312N-GBS C (1.5V × 1)
RB-9313N-GBSU C (1.5V × 1)
Front
Front
Front
Front
Front
Front
Front
+
-
C (1.5V × 1) D (1.5V × 2)
+
+-
-
+
-
C (1.5V × 1) D (1.5V × 2)
+
+-
-
+
+
-
-
C (1.5V × 1)
C (1.5V × 1)
D (1.5V × 2)
+
+
+
+
-
-
-
-
+
+
-
-
+
-
+
-
+
+
-
-
+
+
-
-

11
●Set the pan support properly as instructed.
* Set pan support to top plate.
Double Simmer Series H, S
Simmer Series H, S
Installation of Gas Hose
●Certified rubber hose for built-in hob must be applied.
●The rubber hose must no be bent during installation and must be at appropriate length (less than 2 m).
●During installation, make sure that the rubber hose must not touch the body
and bottom part of the built-in hob.
●Set the securing ring over the rubber hose and connect to the gas inlet rear
side of the built-in hob till the red marked line. Secure the position of rubber
hose by tightening securing ring.
●The installation of gas hose must be performed by a qualified installer according
totherelevantstandards(ForLPGas).
Important
Once installation is complete, check the perfect seal of every pipe fitting, using a soapy
solution, never a flame.
InnerFlameSeriesH,S
H Burner S Burner
H Burner
H Burner
S Burner
S Burner
Mega Series
Gas inlet Securing
ring
Red marked
line
Rubber hose

12
Ignition
1. Pressthecontrolknobforabout3mmandturntotheleft(counterclock-wise)tothe“●●●”(MAX)
position.
2 In the event of the burner flames being accidentally extinguished, turn off the burner control and do
not attempt to re-ignite the burner for at least 1 min. If the burner has not lit up after 15 seconds,
stop operating the built-in hob and open the compartment door and/or wait for at least 1 minute
before attempting to ignite the burner again.
3.Theflamecanbecontrolledbetween“●●●”(MAX)
and“●”(MIN) position, please adjust the flame
slowly.
4. Do not clean the top of the sensor with a hard
brush, as it may damage the sensor.
Flame Extinguishing
1.Aftertheusage,turnthecontrolknobright(clock-wise)totheoriginal“●”positionandtheflamewill
be extinguished.
2.Afterextinguishingoftheflame,donottouchtheconductivepartsofthebuilt-inhobastheymay
remain at high temperature.
3. There might be a slight hissing sounds after the extinguishing of the flame.
4. If the built-in hob is not in use, turn off the main gas supply in order to avoid gas leakage or
unnecessary accidents.
How to Handle Safety Device
1. If the flame is extinguish during operation, the flame failure safety device will automatically cut off the
gas within second.
  Ifyounoticethattheflamehasbeenextinguished,pleaseturntheknobto“●”positionanddonot
attempt re-ignite the burner at least 1 minute.
Max Position Min Position
6. Operating Instructions

13
How to Change Battery
1. If the battery ran out, open the cabinet door and change it correctly. The location of the battery is
described in Page 10.
  •Batteryboxislocatedatbottomofbuilt-inhob.
Open the cabinet door and change the battery.
* Set battery correctly with care. +-
7. Maintenance
How to set Drip Pan
InnerFlameSeries
* Set Burner Cover properly as instructed.
* Set drip pan into burner correctly, without gap.
Mega Series
* Set the drip pan properly as instructed.
×
×
✓
✓
Gap
Gap
Burner Cover
Slot
Slot
Pin
Pin
Drip Pan
Drip Pan

14
* Set Burner Head H on Top Burner Body HS properly. The Pin of Burner Head H shall be located
onto the Slot on Top Burner Body HS.
Set Burner Head S on the Top Burner Body HS properly.
×
✓×
Burner Head S
Burner Head H
Top Burner Body HS
Gap Gap
Slot
Pin
Double Simmer Series H, S
* Install Burner Body H to Burner Base H properly. The Slot on Burner Body H shall be properly
located onto the Pin of Burner Base H.
* Install Burner Head H to Burner Body H properly. The Slot on Burner Body H shall be properly
located onto the Pin of Burner Head H.
* Install Simmer Burner Head to Burner Body H properly. The Slot on Burner Body H shall be properly
located onto the Pin of Simmer Burner Head.
Burner Base H
Burner Body H Simmer Burner Head
Burner Body H
Burner
Head H
Slot
Slot
Slot
Pin
Pin
Pin
Slot
Pin

15
* Install Burner Body S to Burner Base S properly. The Slot on Burner Base S shall be properly located
onto the Guide Pin of Burner Body S.
* Set Burner Head S on Burner Body S.
* Set Burner Head on Burner Body H properly without gap as below illustration.
×
✓×
Gap
Gap
×
Gap
Burner Base SSlot Slot
Guide Pin
Pin
Burner Head S
Burner Body S
Simmer Burner
Head
Burner Body H

16
Simmer Series H, S
* Set burner Body H on burner base H. Be careful to align guide pin of burner body with slot of burner
base.
* Install Burner Cap H and Simmer Burner Cap properly onto Burner Body H.
* Install Burner Body S to Burner Base S properly.
The Slot on Burner Base S shall be properly located onto the Guide Pin of Burner Body S.
* Set Small Burner Cap on Burner Body S.
* Set burner cap on burner body properly without gap as below illustration.
×
×
✓×
Burner Cap
Burner Body
Gap Gap
Burner Body H
Burner Body S
Guide Pin
Guide Pin
Burner Base H
Burner Base S
Burner Body S
Small Burner Cap
Simmer Burner Cap
Burner Cap H
Slot
Slot
Gap

17
FAULT CAUSE REMEDY
1. No Ignition Spark electrode is wet, especially in
high humidity season.
Dry the electrode with clean tissue
or dry cloth.
2.Flamecannot
be held.
Incorrect turning of gas control
knob.
Push and turn the gas control knob
anti-clockwise until a ‘click’ sound
is heard. Hold for a few seconds
until flame is ignited.
3. No main flame. Gas regulator has been turned off. Open gas regulator completely.
4. Yellow flame. Accumulatedgreaseanddirtonthe
burner.
Wash the burner in warm water
with detergent. Leave it to dry, then
place it back in the correct position.
5. Unstable flame. Incorrect location of burner head. Refit burner head into burner ring.
8. Trouble Shootings

18
Model Net
Weight
Overall
Dimension
Cut out
hole size
(mm)
Ignition
Battery Size
Respective gas consumption (kW) Gas
Connecting
Tube
High Medium small all Type of
gas
30 cm
RB-3311S-GBS
6.8 310 x 520 x 130
268 x 490
R0~R50 C (1.5V × 1)
3.7 — — 3.7
L.P.G
(30 mbar)
ø 9.5 mm
gas specific
rubber hose
RB-3312S-GBS
8.1 310 x 520 x 130 3.2 —1.6 4.7
RB-3311D-GBS
7.8 310 x 520 x 136 4.2 — — 4.2
RB-3311M-GBS
8.2 310 x 520 x 127 5.0 — — 5.0
RB-3311N-GBS
7.1 310 x 520 x 112 3.5 — — 3.5
60 cm
RB-6313S-GBST
14.2 620 x 520 x 130
560 x 480
R0~R50
C (1.5V × 1) 3.7 —1.6 x 2 6.8
RB-6323S-GBST
14.6 620 x 520 x 130 C (1.5V × 1) 3.7 3.2 1.6 8.2
RB-6314S-GBS
16.0 620 x 520 x 130 D (1.5V × 2) 3.2 x 2 —1.6 x 2 9.3
RB-6313D-GBST
15.4 620 x 520 x 136 C (1.5V × 1) 4.2 —1.5 x 2 7.2
RB-6313M-GBST
15.8 620 x 520 x 127 C (1.5V × 1) 5.0 —1.5 x 2 8.0
75 cm
RB-7312S-GBS
16.4 770 x 520 x 130
725 x 480
R0~R50
C (1.5V × 1) 3.7 x 2 — — 7.2
RB-7313S-GBST
17.2 770 x 520 x 130 C (1.5V × 1) 3.7 —1.6 x 2 6.8
RB-7323S-GBST
17.4 770 x 520 x 130 C (1.5V × 1) 3.7 3.4 1.6 8.5
RB-7314S-GBS
18.8 770 x 520 x 130 D (1.5V × 2) 3.4 x 2 —1.6 x 2 9.7
RB-7315S-GBS
20.0 770 x 520 x 130 D (1.5V × 2) 3.4 x 2 —1.6 x 3 11.0
RB-7313D-GBST
18.0 770 x 520 x 136 C (1.5V × 1) 4.2 —1.5 x 2 7.2
RB-7312M-GBS
18.9 770 x 520 x 127 C (1.5V × 1) 5.0 x 2 — — 9.9
RB-7313M-GBST
18.6 770 x 520 x 127 C (1.5V × 1) 5.0 —1.5 x 2 8.0
RB-7312N-GBS
16.9 770 x 520 x 112 C (1.5V × 1) 3.5 x 2 — — 6.8
90 cm
RB-9312S-GBS 17.3 880 x 520 x 130
830 x 470
R0~R100
C (1.5V × 1) 3.7 x 2 — — 7.2
RB-9313S-GBST
17.7 880 x 520 x 130 C (1.5V × 1) 3.7 x 2 —1.6 8.7
RB-9314S-GBS
19.8 880 x 520 x 130 D (1.5V × 2) 3.7 x 2 —1.6 x 2 10.3
RB-9315S-GBS
21.0 880 x 520 x 130 D (1.5V × 2) 3.7 x 2 —1.6 x 3 11.5
RB-9312D-GBS
18.8 880 x 520 x 136 C (1.5V × 1) 4.2 x 2 — — 7.9
RB-9213D-GBST
20.1 880 x 520 x 136 C (1.5V × 1) 4.2 x 2 —1.5 9.4
RB-9314D-GBS
21.5 880 x 520 x 136 D (1.5V × 2) 4.2 x 2 —1.5 x 2 10.7
RB-9315D-GBS
22.8 880 x 520 x 136 D (1.5V × 2) 4.2 x 2 —1.5 x 3 12.2
RB-9312M-GBS
19.6 880 x 520 x 127 C (1.5V × 1) 5.0 x 2 — — 9.9
RB-9313M-GBST
20.6 880 x 520 x 127 C (1.5V × 1) 5.0 4.2 1.5 10.4
RB-9312N-GBS
17.7 880 x 520 x 112 C (1.5V × 1) 3.5 x 2 — — 6.8
RB-9313N-GBSU
19.2 880 x 520 x 112 C (1.5V × 1) 3.5 2.9 1.5 7.8
9. Technical Specifications

19

20
http://www.rinnai.com