RIOTEC DC9257L User manual

1
Programming Quick Guide
-DC9257L: Docking Scanner
-DC9267L: Wearable Scanner
Docking Scanner:
Gently tap the trigger area at the middle of scanner, to enable the
scanner(for reading barcode)
Wearable Scanner:
Press the ring trigger to enable the scanner.
Up Side
Lower Side
The touch sensor area is around middle of the scanner as drawing shown.
Installation
They are Plug &Play USB (HID) devices. When plugged into your Android
OTG devices, it can be recognized as barcode scanner and begin to scan
the barcode. Before using scanner, make sure the smartphone or tablet
is fully charged. Open your APP, they can work as a keyboard input.
Reset Configuration to Default
(scan from 1 to 3)
1
0006010
3
0006000
2
0001160
Barcode Configuration Method:
(Flow chart for setup procedure :)
Start
Configuration
End
Configuration
0006010
0006000
Keyboard Country (For USB HID only)
Scan the appropriate country code as below to program the keyboard
layout for your country or language. As a general rule, the following
characters are supported, but need special care for countries other
than the United States: @ | $ # { } [ ] = / ‘ \ < > ~
1103001
1103002
USA
Japan
1103003
1103004
Denmark
Finland
1103005
1103227
France
UK
1103007
1103008
Italy
Norway
1103006
1103226
Turkey F
Turkey Q
Keyboard Country (For USB HID only)
Scan the appropriate country code as below to program the keyboard
layout for your country or language. As a general rule, the following
characters are supported, but need special care for countries other
than the United States: @ | $ # { } [ ] = / ‘ \ < > ~
1103202
1103222
Belgium
Spain
1103209
1103220
Germany
Austria
Russia
1103223
1103218
Sweden
Portugal
1D Symbologies –1
ENABLE
UPC-E
DISABLE
0403020
0403010
ENABLE
UPC-A
DISABLE
0404020
0404010
ENABLE
Code 128
DISABLE
0400020
0400010
ENABLE
GS1-128
UCC/EAN-128
DISABLE
0412020
0412010
Trigger
Area

2
Barcode Configuration Method:
(Flow chart for setup procedure :)
Start
Configuration
End
Configuration
0006010
0006000
1D Symbologies –2
ENABLE
Code 39
DISABLE
0408020
0408010
ENABLE
Code 93
DISABLE
0410020
0410010
1D Symbologies –3
ENABLE
EAN-8
DISABLE
0401020
0401010
ENABLE
EAN-13
DISABLE
0402020
0402010
ENABLE
ISSN
DISABLE
0421020
0421010
ENABLE
ISBN
DISABLE
0416020
0416010
ENABLE
Codabar
DISABLE
0409020
0409010
ENABLE
GS1-Databar
(RSS)
DISABLE
0413020
0413010
ENABLE
Interleaved
2 of 5
DISABLE
0405020
0405010
2D Symbologies
ENABLE
Data
Matrix
DISABLE
0504020
0504010
ENABLE
QR Code
DISABLE
0502020
0502010
ENABLE
Micro
QR Code
DISABLE
0502110
0502100
ENABLE
PDF 417
DISABLE
0501020
0501010
Inter-Keystroke Delay (For USB HID only)
This parameter specifies the delay between emulated keystrokes.
No Delay
1103050
Short Delay
(20ms)
Long Delay
(40ms)
1103051
1103052

3
How to put trigger cable into plastic buckle:
1.plastic wire buckle of DC9267A
2.press the plastic buckle and pull backward
3. release the lock
4.make sure the lock is released
5.put trigger cable into plastic buckle
6.push plastic buckle to make it locked.
Information in this document is subject to change without notice.
For more information, please visit:
www.riotec.com.tw
R_180717_01