RIOTEC DC9257LP User manual

1
*
Quick Guide
-DC9257LP
1
H92P
Connect to micro USB port of OTG device
2
H92P
3
*Before you use it, please switch to "C" for battery charge for
3~4 hours.
*Under “C mode”, you can raise/lower soft-keyboard easily.
4
H92P Scan Holder is with Li-Ion battery inside. When in
charging, please use the original power adaptor of
smartphone (recommend). Through it, it charges both OTG
device and H92P internal battery at the same time. When in
low battery (Red LED flashing), please charge it
immediately.
LED Indicator Information
Green LED OFF
Full charged (Charge mode)
Green LED ON
Charging (Charge mode)
Red LED Flashing
Low battery (Operation mode)
Attention: Under “Operation mode” please do not charging,
otherwise the OTG device's battery will be charging back to
H92P’s battery.
5
The touch trigger is in the central area of mini scanner. (for both side).
Please check the above drawing for your reference.
Installation
Before using scanner, please make sure that the OTG device is fully
charged.
1. Under USB HID interface
** When plugged into OTG device, it will be recognized and begin
to scan the barcode.
2. Under USB Serial interface
** Please install PL-2303 driver into your OTG device first. PL-2303
driver can be downloaded from Google Play
** Connect scanner to your OTG device, then, you can know which
serial port scanner connects to.
** The data you scan will be sent to serial port and your APP can
get the data from serial port directly.
Reset Configuration to Default
(scan from #1 to #3)
1
0006010
3
0006000
2
0001160
Suction Cup
PU Glue
(Can be used
repeatedly)
Micro USB
port (OTG)
Li- Ion
Battery
O = Operation mode
C = Charge mode
LED Indicator
LED Indicator
Trigger
Area
Mini
scanner

2
Barcode Configuration Method:
(Flow chart for setup procedure :)
0006010
0006000
Start
Configuration
End
Configuration
Keyboard Country (For USB HID only)
Scan the appropriate country code as below to program the
keyboard layout for your country or language. As a general
rule, the following characters are supported, but need special
care for countries other than the United States:
@ | $ # { } [ ] = / ‘ \ < > ~
1103202
1103222
Belgium
Spain
1103209
1103220
Germany
Austria
Russia
1103223
1103218
Sweden
Portugal
Keyboard Country (For USB HID only)
Scan the appropriate country code as below to program the
keyboard layout for your country or language. As a general
rule, the following characters are supported, but need special
care for countries other than the United States:
@ | $ # { } [ ] = / ‘ \ < > ~
1103001
1103002
USA
Japan
1103003
1103004
Denmark
Finland
1103005
1103227
France
UK
1103007
1103008
Italy
Norway
1103006
1103226
Turkey F
Turkey Q
1D Symbologies –1
ENABLE
GS1-Databar
(RSS)
DISABLE
0413020
0413010
ENABLE
UPC-E
DISABLE
0403020
0403010
ENABLE
UPC-A
DISABLE
0404020
0404010
ENABLE
Interleaved
2 of 5
DISABLE
0405020
0405010
ENABLE
Code 128
DISABLE
0400020
0400010
ENABLE
GS1-128
UCC/EAN-128
DISABLE
0412020
0412010
ENABLE
MSI
DISABLE
0420020
0420010

3
Barcode Configuration Method:
(Flow chart for setup procedure :)
0006010
0006000
Start
Configuration
End
Configuration
1D Symbologies –2
ENABLE
Matrix
2 of 5
DISABLE
0406020
0406010
ENABLE
Industrial 25
DISABLE
0417020
0417010
ENABLE
Code 39
DISABLE
0408020
0408010
1D Symbologies –3
ENABLE
EAN-8
DISABLE
0401020
0401010
ENABLE
EAN-13
DISABLE
0402020
0402010
ENABLE
Code 93
DISABLE
0410020
0410010
ENABLE
Codabar
DISABLE
0409020
0409010
ENABLE
ISSN
DISABLE
0421020
0421010
ENABLE
ISBN
DISABLE
0416020
0416010
2D Symbologies
ENABLE
Data
Matrix
DISABLE
0504020
0504010
ENABLE
QR Code
DISABLE
0502020
0502010
ENABLE
Micro
QR Code
DISABLE
0502110
0502100
ENABLE
PDF 417
DISABLE
0501020
0501010
Inter-Keystroke Delay (For USB HID only)
This parameter specifies the delay between emulated keystrokes.
No Delay
1103050
Short Delay
(20ms)
Long Delay
(40ms)
1103051
1103052
Information in this document is subject to change without notice.
For more information, please visit:
www.riotec.com.tw
R_151116_03