Riverside Furniture 67802 User manual

2 Leg Assembly
1Stretcher
16 Bolts 3/16 x 1/2
P pS Screwdriver (NOT INCLUDED)
It is strongly recommended that this table be assembled by TWO PERSONS to avoid marking or scratching the finish.
It is easier to assemble this product upside down.
It is recommended that you periodically check and tighten all parts during the lifetime of the product.
Clean with a damp cloth and buff dry with a soft cloth. Use of commercial polishes or waxes is not recommended.
Use coasters under beverages and articles that may scratch. Do not place hot items directly on the surface.
LEG ASSEMBLY (2)WOOD TOP
1 Wood Top
67802 / 67809 / 67812 / 67815
STRETCHER
8 Screws #10 x 3/4
ASSEMBLY INSTRUCTION
Thank you for purchasing this quality product. Be sure to check all packing material carefully for small parts which may
have come loose inside the carton during shipment. Identify and count all parts and compare with parts list below.
MADE IN MEXICO
TOOLS REQUIRED
BUT NOT PROVIDED
PART LIST HARDWARE LIST
Philips Screwdriver
4Angle Bracket
LEG ASSEMBLY
STRETCHER
WOOD TOP
BOLTS
(3/16 x1/2”)
BOLTS
(3/16 x1/2”)
SCREWS
(#10x3/4”)
Angle Bracket Detail
1. Locate and unpack all the parts and place them on a soft surface such as a blanket or carpet.
2. Match the numbers on the base to the numbers on top.
3. Place the Wood Top upside down on a soft surface and while lifting one end, insert one Leg Assembly into
the channel of the Wood Top.
4. Attach a Metal Bracket to the Leg Assembly using the 3/16” x 1/2” Bolts as shown. Leave Loose.
5. Repeat Steps 3 & 4 above for other Leg Assembly.
6. Screw the Angle Bracket to the Wood Top using the #10 x 3/4” Wood Screws as shown.
7. Attach the Stretchers to the bottom of the Leg Assembly using 3/16” x 1/2” Bolts as shown. Tighten all Bolts.
8. Turn the completed table upright.
NOTICE: 67815 Sofa Table includes an Anti-Tipping Restraint Kit (#HH510)

1. Temporarily locate the furniture to near it's fInal location In the room next to a wall. Locate a
wall stud behInd your furniture and also mark the stud's location on the back of your furniture.
2. Firmly attach one bracket to the stud approximately 2" below the top of the furniture with the
2 Inch long Wood Screws provided. It may be necessary to drill 3/32 dia. pilot holes for the screws.
3. Firmly attach the other bracket onto a solid, structural part on the back of the furniture usIng the
5/8 Inch long Wood Screws. It may also be necessary to pilot bore for these screws.
4. Move the furniture Into its fInal position, takIng care to lIne up the wall bracket with the
furniture bracket. Thread a strap through the bracket as shown In the illustration. Tighten strap
until snug but do not over tighten.
Caution: Riverside Furniture Corp. assumes no liability for improper Installation or excessive
loads placed on screws, brackets or straps. Failure to detach this restraInt before movIng furniture
may result In personal Injury and property damage.
WarnIng: This tip-over restraInt is not to be a substitute for proper adult supervision. Do not allow
children to climb on furniture. Items left on top of the TV and furniture, such as toys, remote
controls and treats might tempt young children to climb. Push the TV as far back as possible from
the front of its stand. Place electrical cords out of a child's reach, and teach children not to play
with the cords.
email: [email protected]m
FURNITURE
Riverside
Approximately
2"
Anti-Tip Hardware
Installation Instructions
Install screws
through the small
hole In brackets
Notice: Riverside Furniture Corp. recommends that steps be taken for certain furniture items to
prevent or minimize the risk of tip-over. This furniture is equipped with Tip-over Restraint
Hardware for use to minimize this risk, if used. Please follow below installation steps. Riverside
Furniture Corp. recommends that parents and guardians periodically visit the U.S. Consumer
Product Safety Commission (CPSC) website at http://www.cpsc.gov/ and stay up to date on all
issues related to children's product safety.
Page 8 of 11