Riverside Furniture 21485 User manual

Made in Viet Nam
Page 1 of 3
8 pcs.
email: [email protected]
FURNITURE
Riverside
Curved Washer
32 L x 13 x 8mm
2 pcs.
1 pc.
Hardware and Parts packed with the King Storage Footboard
F-A
F-E F-F
2 pcs.
Ø5
16-18 x 3" Long
Allen Head Bolt
4 pcs.
#8 x 1" Wood
Screw
F-G
King Storage
Footboard
Hardware and Parts packed with the 5/0-6/6 Bed Rails
8 pcs. 8 pcs.
Ø5
16-18 x 4-1/2" Long
All-Thread Bolt
8 pcs.
Queen / Eastern King
Bed Rail
2 pcs.
R-A R-B R-C R-D R-E
R-F 8 pcs.
Ø5
16-18 Hex Nut
12mm Open Wrench
Slat Support Rails
King Roll Slat
1 pc.
F-B 2 pcs.
F-C 1 pc.
F-D
Slat Support Leg
Precision Bed Room
King Bed
Assembly Instructions
Ø5
16-18 x 1-1/4" Long
Allen Head Bolt
Ø5
16 x 12 x 3mm
Spring Washer
Ø5
16 x 19 x 2mm
Flat Washer
4 pcs.F-H
F-I 30 pcs. 1 pc.
5mm Allen Wrench
F-J
Ø5
16 x 12 x 3mm
Spring Washer
Wood Dowel Pin
R-G 4 pcs.
8 pcs.
Curved Washer
32 L x 13 x 8mm
Hardware and Parts packed with the 6/0 California King Bed Rails
8 pcs. 8 pcs.
Ø5
16-18 x 4-1/2" Long
All-Thread Bolt
8 pcs.
California King Bed
Rail
2 pcs.
R-A R-B R-C R-D R-E
R-F 8 pcs.
Ø5
16-18 Hex Nut
12mm Open Wrench
Ø5
16 x 12 x 3mm
Spring Washer
Wood Dowel Pin
R-G 4 pcs. 1 pc.
4mm Allen Wrench
R-H
21485 / 21885 6/0-6/6 STORAGE FOOTBOARD
21476 / 21876 5/0-6/6 BED RAILS --OR--
21486 / 21886 6/0 BED RAILS
21480 / 21880
LOW HEADBOARD
21484 / 21884
TALL HEADBOARD
21482 / 21882
LOW UPH HEADBOARD
21488 / 21888
TALL UPH HEADBOARD
21485 / 21885 6/0-6/6 STORAGE FOOTBOARD
21476 / 21876 5/0-6/6 BED RAILS --OR--
21486 / 21886 6/0 BED RAILS
Part A
Part B
Note: The Allen Wrench (R-H) is used to remove, then reattach
the Filler Rail mounted at the top edge of the California King
Bed Rails.
Be sure to check all packing material carefully for small parts, which may have come loose inside the carton
during shipment. To prevent possible scratches or damage, this furniture should be assembled on a soft surface
such as a blanket or carpet.
To prevent possible damage to furniture and personal injury, it is recommended that two people are used to
assemble and set-up this bed.

Page 2 of 3
email: [email protected]
FURNITURE
Riverside
Adj Glide
STEP 3
Detail E
Steps:
1. Lean the back of the Headboard against the wall where the Bed will be
assembled.
2. Install two All-Thread Bolts (R-B) into the metal threaded inserts installed in the
Headboard Legs and into the metal inserts on the Footboard. Insert the Wood
Dowel Pins (R-G) into the middle holes.
3. Carefully position one end of one Bed Rail (R-A) onto the All-thread Bolts on
the Headboard and connect using the Curved Washers (R-E), Spring Washers
(R-D), and Hex Nut (R-C). Only partially tighten the Nuts until the Footboard
has been connected. Repeat for other Bed Rail.
4. Position and connect the Footboard (F-A) to the other end of the Bed Rails,
attaching as in the previous Steps.
8. Carefully align the Footboard to be 'square' with the Headboard. Using the
Open Wrench (R-F) tighten all Hex Nuts attaching the Side Rails to the
Headboard and Footboard. (See Detail E).
F-C
F-C
F-C
F-D
F-D
6. Assemble Parts A & B of the Slat Support Rails (F-C) using the two 1-1/4"
long Bolts (F-F), Spring Washers (F-G) and Flat Washers (F-H). Assemble the
Slat Support Leg (F-D) to the Support Rails using the two 3" Long Bolts (F-E)
and the same Washers. Tighten all four Bolts with the Allen Wrench (F-J).
7. Position the Slat Support assembly into the pockets on the Headboard and
Footboard.
R-B
R-E
R-D
R-C
R-F
R-G
F-F
F-G
F-H
F-J
F-E
F-G
F-H
F-J
Note: Use these four holes
when assembling the Slat
Support Rails for a Queen or
Eastern King Bed.
Note: Use these four holes
when assembling the Slat
Support Rails for a California
King Bed.
68-3/8" For Queen / Eastern King
72-3/8" For California King
NOTE: The Slat Support Rails Parts A
& B, and Support Leg, can be
assembled to fit a Queen/King Bed or
to fit a California King Bed length,
depending on the sets of holes used.
Made in Viet Nam
Precision Bed Room
King Bed
Assembly Instructions
21485 / 21885 6/0-6/6 STORAGE FOOTBOARD
21476 / 21876 5/0-6/6 BED RAILS --OR--
21486 / 21886 6/0 BED RAILS
21480 / 21880
LOW HEADBOARD
21484 / 21884
TALL HEADBOARD
21482 / 21882
LOW UPH HEADBOARD
21488 / 21888
TALL UPH HEADBOARD
21485 / 21885 6/0-6/6 STORAGE FOOTBOARD
21476 / 21876 5/0-6/6 BED RAILS --OR--
21486 / 21886 6/0 BED RAILS

Page 3 of 3
email: [email protected]
FURNITURE
Riverside
After the Bed is assembled, completely unroll the Bed Roll Slat (F-B) onto the
Bed.
For an Eastern King Bed, disregard Steps 1 and 3 shown below.
Using your Phillips Screwdriver, attach the Slats nearest the Headboard and
Footboard and attach the middle of the Slats to the Slat Support Rails in the
middle of the Bed using the 1" Long Wood Screws (F-I).
Steps 1 and 3 below apply for California King Bed Rails only. These Bed Rails
use a wood filler attached to the top inside edge of the Bed Rails, which must
be removed using the Allen Wrench supplied with the Bed Rails (Step 1
below), install the Bed Slats (Step 2 below) and then reattach the filler rails
(Step 3 below).
R-A
F-I
Made in Viet Nam
Precision Bed Room
King Bed
Assembly Instructions
21485 / 21885 6/0-6/6 STORAGE FOOTBOARD
21476 / 21876 5/0-6/6 BED RAILS --OR--
21486 / 21886 6/0 BED RAILS
21480 / 21880
LOW HEADBOARD
21484 / 21884
TALL HEADBOARD
21482 / 21882
LOW UPH HEADBOARD
21488 / 21888
TALL UPH HEADBOARD
21485 / 21885 6/0-6/6 STORAGE FOOTBOARD
21476 / 21876 5/0-6/6 BED RAILS --OR--
21486 / 21886 6/0 BED RAILS
Step 1
Step 2
Wood
Filler rail
Step 3
Wood
filler rail