Riverside AVON User manual

8 pcs.
R-B 8 pcs. 1 pc.
12 mm Open WrenchØ5/16''x 3" Long Bolt
R-C R-D
Hardware and Parts packed with the Bed Rails
2 pcs.
R-A
Hardware and Parts packed with the Headboard
Panel Headboard
1 pc. One Left &
One Right 1 pc.
Headboard Post Headboard Stretcher
Made in Viet Nam
email: [email protected]
Page 1 of 4
H-A H-B H-C
AVON
Bedroom
Assembly Instructions
4 pcs.
H-G
Ø1/4'' x 1-1/4"
Allen Head Bolt
1 pc.
H-H H-I H-J
Allen key
Ø1/4'' x Ø19mm
Flat Washer
Ø1/4'' x Ø10mm
Spring Washer
6 pcs.
H-D
Ø5/16'' x 1-3/4"
Allen Head Bolt
H-E H-F
Ø5/16'' x Ø19mm
Flat Washer
Ø5/16'' x Ø12mm
Spring Washer
4/6 -5/0 Queen Bed
28870--4/6-5/0 Panel Headboard
28871--4/6-5/0 Panel Footboard &Slats
28872 -- 5/0-6/6 Panel Bed Rails
37*17mm Arc Washer Ø5/16''-18mm Nut
R-E
8 pcs.
6 pcs. 6 pcs. 4 pcs. 4 pcs.
Hardware and Parts packed with the Footboard
Panel Footboard Slats Screw #8*30mm
F-A 1 pc. F-B 2 pcs. F-C 4 pcs. F-D 4 pcs. F-E 8 pcs.
Support leg
Bun Foot
Panel Bed Rails

Made in Viet Nam
email: [email protected]
Page 2 of 4
AVON
Bedroom
Assembly Instructions
F-A
F-B
H-G
H-H
H-I
H-J
H-A
H-B H-C
H-D
H-E
H-F
H-J
ASSEMBLY STEPS:
1. Place the Headboard Panel (H-A) face down on a soft surface such as a blanket or carpet.
2. Attach the Left and Right Legs (H-B) to the back of the Headboard Panel using the Allen-Head Bolts (H-D), Spring
Washers (H-E) and Flat Washers (H-F). Do not fully tighten Bolts until after next step.
3. Attach the Stretcher (H-C) to the Legs as shown using the Allen-Head Bolts (H-G), Spring Washers (H-H) and Flat
Washers (H-I). Do not fully tighten Bolts until after next step.
4. Adjust parts for correct fit if necessary and tighten all Bolts using the Allen Key (H-J).
5. Carefully lean the assembled Headboard against the wall where the bed will be used.
6. Install the bun feet onto the bottom footboard as shown.
Note: There are levelers installed in the bottom of the posts which can be adjusted if needed.

F-E
F-C
Made in Viet Nam
email: [email protected]
Page 3 of 4
AVON
Bedroom
Assembly Instructions
R-A
R-D
R-B
R-E
R-C
F-A
R-A
H-A
F-D
F-C
Steps:
7. Install all the All-Thread Bolts (R-D) into the metal threaded inserts installed in the Headboard Legs and into the metal inserts on the Footboard.
8. Carefully position one end of one Bed Rail (R-A) onto the All-thread Bolts on the Headboard and connect using the Arc Washer (R-B) & Nut
(R-C). Only partially tighten the Nuts until the Footboard has been connected. Repeat for other Bed Rail.
9. Position and connect the Footboard (F-A) to the other end of the Bed Rails, attaching as in the previous Steps.
10. Carefully align the Footboard to be 'square' with the Headboard. Using the Open Wrench (R-E) tighten all of the Nuts as shown.
11. Attach a support foot (F-D) to each slat (F-C) as shown.
12. Position the slats onto the side rails, making sure to space them evenly.
13. Attach the slats with the wood screws (F-E) as shown.

Page 4 of 4
Made in Viet Nam
email: [email protected]
USE THESE HOLES FOR ATTACHING WOOD SIDE RAILS.
ALL HARDWARE IS INCLUDED WITH THE SIDE RAILS
USE THESE HOLES FOR ATTACHING A FULL SIZE (4/6)
METAL BED FRAME
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
CUSTOMER TO PROVIDE 5/16 X 1-1/2" LONG BOLTS, NUTS
& WASHERS TO CONNECT THE METAL BED FRAME
USE THESE HOLES FOR ATTACHING A QUEEN SIZE (5/0)
METAL BED FRAME
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
CUSTOMER TO PROVIDE 5/16 X 1-1/2" LONG BOLTS, NUTS
& WASHERS TO CONNECT THE METAL BED FRAME
AVON
Bedroom
Assembly Instructions
28870 -- 4/6-5/0 Panel Headboard