Riverside Aberdeen King Bed User manual

6/6 King Bed
21284 -- 6/0-6/6 Panel Headboard
21285 -- 6/0-6/6Panel Bed Footboard & Slats
21272 --5/0 -6/6Panel Bed Rails (for 6/6 Bed)
OR
21282 -- 6/0 Panel Bed Rails
8 pcs. 8 pcs.
8 pcs. 8 pcs. 8 pcs.
1 pc.
2 pcs.
Aberdeen
King Bed Bed
Assembly Instructions
Made in Viet Nam
email: [email protected]
FURNITURE
Riverside
8 pcs.
1 pc.
Page 1 of 4
8 pcs.
4 pcs. 8 pcs.

Page 2 of 4
Aberdeen
King Bed
Assembly Instructions
Made in Viet Nam
email: [e-mail]
FURNITURE
Riverside
ASSEMBLY STEPS :
1. Place the Headboard Panel (H-A) face down on a clean and soft surface.
2. Attach the Left and Right Headboard Posts (H-B) to the back of the Headboard Panel,
using the Flat Washers (H-F), Spring Washers (H-E) and 1-3/4" Long Bolts (H-D). Do
not fully tighten until after next step. (see Detail A).
3. Attach the Headboard Stretcher (H-C) to the Headboard Posts using the same Washers
and Bolts (H-D) as in previous step.
4. Tighten all Bolts using the Allen Wrench (H-G). (see Detail A & B).
Gently lean the back of the assembled Headboard against the wall where the Bed will be
located in the room.

Page 3 of 4
Aberdeen
King Bed
Assembly Instructions
Made in Viet Nam
email: [e-mail]
FURNITURE
Riverside
ASSEMBLY STEPS :
To prevent possible damage to furniture and personal injury, it is recommended that two people are used
to perform the following steps.
5. Install two All-Thread Bolts (R-B) into the metal threaded inserts installed in the Headboard Posts and
into the metal inserts on the Footboard.
6. Carefully position one end of one Bed Rail (R-A) onto the All-thread Bolts on the Headboard and
connect using the Arc Washers (R-F), Flat Washers (R-E), Spring Washers (R-D), and Hex Nut (R-C).
Only partially tighten the Nuts until the Footboard has been connected. Repeat for other Bed Rail.
7. Position and connect the Footboard (F-A) to the other end of the Bed Rails, attaching as in the previous
Steps.
8. Carefully align the Footboard to be 'square' with the Headboard. Using the Open Wrench (R-G) tighten
all Hex Nuts attaching the Side Rails to the Headboard and Footboard. (See Detail E ).
9. Attach the eight Support Legs (F-C) to the bottom side of four Wood Slats (F-B). (See Detail D).
10. Position and attach the Slats to the Bed Rails using the Wood Screws (F-D) and your Phillips
Screwdriver. (See Detail E).
The levelers located at the bottom of the Support Legs can be adjusted if necessary to support the Slats.

Riverside
email: [e-mail]
Page 4 of 4
USE THESE HOLES FOR ATTACHING WOOD SIDE RAILS.
ALL HARDWARE IS INCLUDED WITH THE SIDE RAILS
USE THESE HOLES FOR ATTACHING A FULL SIZE (4/6)
METAL BED FRAME
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
CUSTOMER TO PROVIDE 5/16 X 1-1/2" LONG BOLTS, NUTS
& WASHERS TO CONNECT THE METAL BED FRAME
USE THESE HOLES FOR ATTACHING A QUEEN SIZE (5/0)
METAL BED FRAME
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
CUSTOMER TO PROVIDE 5/16 X 3-1/2" LONG BOLTS, NUTS
& WASHERS TO CONNECT THE METAL BED FRAME
21284
King Panel Bed Headboard
21284 -- 6/0-6/6 Panel Headboard
21285 -- 6/0-6/6 Panel Footboard w/Slats
21272 -- 5/0-6/6 Bed Rails
21282 -- 6/0 Bed Rails
The Headboard may be used alone with
an Eastern King or California King
Metal Bed Frame
#11872 QUEEN/
EASTERN KING RAILS