Riverside Aberdeen Queen Bed User manual

5/0 Queen Bed
21270 -- 4/6-5/0 Reeded Headboard
21271 -- 5/0 Reeded Footboard & Slats
21272 -- 5/0-6/6 Bed Rails (for 5/0 Bed)
8 pcs. 8 pcs.
8 pcs. 8 pcs. 8 pcs.
1 pc.
2 pcs.
Aberdeen
Queen Bed
Assembly Instructions
Made in Viet Nam
email: [email protected]
FURNITURE
Riverside
8 pcs.
1 pc.
Page 1 of 4
8 pcs.
4 pcs.

Page 2 of 4
ASSEMBLY STEPS :
1. Place the Headboard Panel (H-A) face down on a clean and soft surface.
2. Attach the Left and Right Headboard Posts (H-B) to the back of the Headboard Panel,
using the Flat Washers (H-F), Spring Washers (H-E) and 1-3/4" Long Bolts (H-D). Do
not fully tighten until after next step. (see Detail A).
3. Attach the Headboard Stretcher (H-C) to the Headboard Posts using the same Washers
and Bolts (H-D) as in previous step.
4. Tighten all Bolts using the Allen Wrench (H-G). (see Detail A & B).
Gently lean the back of the assembled Headboard against the wall where the Bed will be
located in the room.
Made in Viet Nam
email: [e-mail]
FURNITURE
Riverside Aberdeen
Queen Bed
Assembly Instructions

Page 3 of 4
Made in Viet Nam
email: [e-mail]
FURNITURE
Riverside
ASSEMBLY STEPS :
To prevent possible damage to furniture and personal injury, it is recommended that two people are used
to perform the following steps.
5. Install two All-Thread Bolts (R-B) into the metal threaded inserts installed in the Headboard Posts and
into the metal inserts on the Footboard.
6. Carefully position one end of one Bed Rail (R-A) onto the All-thread Bolts on the Headboard and
connect using the Arc Washers (R-F), Flat Washers (R-E), Spring Washers (R-D), and Hex Nut (R-C).
Only partially tighten the Nuts until the Footboard has been connected. Repeat for other Bed Rail.
7. Position and connect the Footboard (F-A) to the other end of the Bed Rails, attaching as in the previous
Steps.
8. Carefully align the Footboard to be 'square' with the Headboard. Using the Open Wrench (R-G) tighten
all Hex Nuts attaching the Side Rails to the Headboard and Footboard. (See Detail C ).
9. Attach the four Support Legs (F-C) to the bottom side of four Wood Slats (F-B). (See Detail D).
10. Position and attach the Slats to the Bed Rails using the Wood Screws (F-D) and your Phillips
Screwdriver. (See Detail E).
The levelers located at the bottom of the Support Legs can be adjusted if necessary to support the Slats.
Aberdeen
Queen Bed
Assembly Instructions

Riverside
email: [e-mail]
The Headboard may be used alone
with a Queen or Full Size
Metal Bed Frame
Page 4 of 4
21270 -- 4/6-5/0 Reeded Headboard
21271 -- 5/0 Reeded Footboard w/Slats
21272 -- 5/0-6/6 Bed Rails
#21272 QUEEN /
EASTERN KING RAILS
USE THESE HOLES FOR ATTACHING WOOD SIDE RAILS.
ALL HARDWARE IS INCLUDED WITH THE SIDE RAILS
USE THESE HOLES FOR ATTACHING A FULL SIZE (4/6)
METAL BED FRAME
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
CUSTOMER TO PROVIDE 5/16 X 1-1/2" LONG BOLTS, NUTS
& WASHERS TO CONNECT THE METAL BED FRAME
USE THESE HOLES FOR ATTACHING A QUEEN SIZE (5/0)
METAL BED FRAME
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
CUSTOMER TO PROVIDE 5/16 X 1-1/2" LONG BOLTS, NUTS
& WASHERS TO CONNECT THE METAL BED FRAME
21270
Queen Reeded Headboard