Riverside Windhaven User manual

5/0 Queen Storage Bed
50770 -- 4/6-5/0 Panel Headboard
50772 -- 5/0-6/6 Bed Rails
50773 -- 5/0 Storage Footboard w/Platform
_______________Note:________________
The 50773 Storage Footboard can be used
with the 50770 Panel Headboard as shown
or with the 50774 Upholstered Headboard
8 pcs. 8 pcs.
8 pcs.
2 pcs.
8 pcs. 8 pcs.
1 pc.
2 pcs.
Windhaven
Queen Storage Bed
Assembly Instructions
Made in Viet Nam
email: [e-mail]
FURNITURE
Riverside
3 pcs.
4 pcs. 1 pc.
3 pcs.
4 pcs. 4 pcs.
1 pc.
Page 1 of 7
8 pcs.
1 pc.

50770 -- 4/6-5/0 Panel Headboard
50772 -- 5/0-6/6 Bed Rails
50771 -- 5/0 Panel Footboard w/Slats
8 pcs. 8 pcs.
8 pcs.
4 pcs.
8 pcs. 8 pcs.
1 pc.
2 pcs.
Windhaven
Queen Standard Bed
Assembly Instructions
Made in Viet Nam
email: [e-mail]
FURNITURE
Riverside
1 pc.
Page 2 of 7
8 pcs.

Page 3 of 7
ASSEMBLY STEPS :
1. Place the Headboard Panel (H-A) face down on a clean and soft surface.
2. Attach the Left and Right Headboard Posts (H-B) to the back of the Headboard Panel,
using the Flat Washers (H-F), Spring Washers (H-E) and Allen-Head Bolts (H-D). Do
not fully tighten until after next step. (see Detail A).
3. Attach the Back Stretcher (H-C) to the Headboard Posts using the same Washers and
Bolts as in previous step.
4. Tighten all Bolts using the Allen Wrench (H-G). (see Detail A & B).
Gently lean the back of the assembled Headboard against the wall where the Bed will be
located in the room.
Windhaven
Bedroom
Assembly Instructions
Made in Viet Nam
email: [e-mail]
FURNITURE
Riverside

Page 4 of 7
Windhaven
Bedroom
Assembly Instructions
Made in Viet Nam
email: [e-mail]
FURNITURE
Riverside
ASSEMBLY STEPS :
1. Remove both drawers from the Storage Footboard. Refer to the steps above.
2. Place the Storage Footboard (F-A) face down on a clean and soft surface.
3. Attach the Drawer Box Support Legs (F-C) using the Flat Washers (F-H), Spring
Washers (F-G) and Bolts (F-F). Tighten with the Allen Wrench (F-I).
To remove the drawer:
A. Pull the drawer fully open so the
black latch is visible in the inside
channel of the guides.
B. Release the latches by
simultaneously pushing one lever up
and the other down.
C. At the same time, pulling the
drawer forward until the slides
release.

Page 5 of 7
Windhaven
Bedroom
Assembly Instructions
Made in Viet Nam
email: [e-mail]
FURNITURE
Riverside
ASSEMBLY STEPS :
To prevent possible damage to furniture and personal injury, it is recommended that two people are used
to perform the following steps.
5. Install two All-Thread Bolts (R-B) into the metal threaded inserts installed in the Headboard Posts and
into the metal inserts on the Storage Footboard.
6. Carefully position one end of one Bed Rail (R-A) onto the All-thread Bolts on the Headboard and
connect using the Arc Washers (R-F), Flat Washers (R-E), Spring Washers (R-D), and Hex Nut (R-C).
Only partially tighten the Nuts until the Footboard has been connected. Repeat for other Bed Rail.
7. Position and connect the Storage Footboard (F-A) to the other end of the Bed Rails, attaching as in the
previous Steps.
8. Carefully align the Storage Footboard to be 'square' with the Headboard. Using the Open Wrench (R-G)
tighten all Hex Nuts attaching the Side Rails to the Headboard and Storage Footboard. (See Detail E ).
9. Attach the three Support Legs (F-D) to the bottom side of three Wood Support Panels with Blocks (F-E).
The Panel Support Legs must be installed into the 6" x 6" x 1/2" blocks mounted on the bottom side of the
panels. (See Detail F). The Support Panel (F-K) used above the drawer compartment does not have a
support leg.
10. Position and attach the Support Panels to the Bed Rails using the Wood Screws (F-J) and your Phillips
Screwdriver.
The levelers located at the bottom of the Support Legs can be adjusted if necessary to support the panels.
11. Reinstall the Drawers into the Footboard by aligning the metal channels of the guides and push back
into the Footboard.
3 pcs.
3 pcs.
1 pc.

Page 6 of 7
Windhaven
Bedroom
Assembly Instructions
Made in Viet Nam
email: [e-mail]
FURNITURE
Riverside
ASSEMBLY STEPS :
To prevent possible damage to furniture and personal injury, it is recommended that two people are used
to perform the following steps.
5. Install two All-Thread Bolts (R-B) into the metal threaded inserts installed in the Headboard Posts and
into the metal inserts on the Standard Footboard.
6. Carefully position one end of one Bed Rail (R-A) onto the All-thread Bolts on the Headboard and
connect using the Arc Washers (R-F), Flat Washers (R-E), Spring Washers (R-D), and Hex Nut (R-C).
Only partially tighten the Nuts until the Footboard has been connected. Repeat for other Bed Rail.
7. Position and connect the Footboard (F-A) to the other end of the Bed Rails, attaching as in the previous
Steps.
8. Carefully align the Footboard to be 'square' with the Headboard. Using the Open Wrench (R-G) tighten
all Hex Nuts attaching the Side Rails to the Headboard and Footboard. (See Detail E ).
9. Attach the four Support Legs (F-D) to the bottom side of four Wood Slats (F-E). (See Detail F).
10. Position and attach the Slats to the Bed Rails using the Wood Screws (F-J) and your Phillips
Screwdriver.
The levelers located at the bottom of the Support Legs can be adjusted if necessary to support the panels.
4 pcs.
4 pcs.

Riverside
email: [e-mail]
USE THESE HOLES FOR ATTACHING A QUEEN SIZE (5/0)
METAL BED FRAME
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
CUSTOMER TO PROVIDE 5/16 X 3-1/2" LONG BOLTS, NUTS
& WASHERS TO CONNECT THE METAL BED FRAME
USE THESE HOLES FOR ATTACHING A FULL SIZE (4/6)
METAL BED FRAME
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
CUSTOMER TO PROVIDE 5/16 X 1-1/2" LONG BOLTS, NUTS
& WASHERS TO CONNECT THE METAL BED FRAME
USE THESE HOLES FOR ATTACHING WOOD SIDE RAILS.
ALL HARDWARE IS INCLUDED WITH THE SIDE RAILS
#50770
Queen / Full Size Headboard
The Headboard may be used alone
with a Queen or Full Size
Metal Bed Frame
Page 7 of 7
#50772 EASTERN
QUEEN / KING RAILS
50770 -- 4/6-5/0 Panel Headboard
50772 -- 5/0-6/6 Bed Rails
50773 -- 5/0 Storage Footboard w/Platform
50770 -- 4/6-5/0 Panel Headboard
50772 -- 5/0-6/6 Bed Rails
50771 -- 5/0 Panel Footboard w/Slats