Riverside Harbor Hill King Storage Bed User manual

25780 -- 6/0-6/6 Panel Headboard
(NOTE: the 25785 Leather Headboard may be used as an alternate)
25774 -- 5/0-6/6 Storage Bed Rails
or---25782 --6/0 Storage Bed Rails
25783 -- 6/0-6/6 Storage Footboard w/Platform
8 pcs. 8 pcs.
8 pcs.
2 pcs.
8 pcs. 8 pcs.
1 pc.
2 pcs.
Harbor Hill
King Storage Bed
Assembly Instructions
Made in Viet Nam
email: [e-mail]
FURNITURE
Riverside
6 pcs.
4 pcs. 1 pc.
3 pcs. 4 pcs. 4 pcs.
1 pc.
Page 1 of 7
8 pcs.
1 pc.

Page 3 of 7
ASSEMBLY STEPS :
1. Place the Headboard Panel (H-A) face down on a clean and soft surface.
2. Attach the Left and Right Headboard Posts (H-B) to the back of the Headboard Panel,
using the Flat Washers (H-G), Spring Washers (H-F) and 2" Long Bolts (H-E). Do not
fully tighten until after next step. (see Detail A).
3. Attach the Back Stretcher (H-C) to the Headboard Posts using the same Washers and
1-5/8" Long Bolts (H-D) as in previous step.
4. Tighten all Bolts using the Allen Wrench (H-H). (see Detail A & B).
Gently lean the back of the assembled Headboard against the wall where the Bed will be
located in the room.
Harbor Hill
Bedroom
Assembly Instructions
Made in Viet Nam
email: [e-mail]
FURNITURE
Riverside Page 3 of 7
ASSEMBLY STEPS :
1. Place the Headboard Panel (H-A) face down on a clean and soft surface.
2. Attach the Left and Right Headboard Posts (H-B) to the back of the Headboard Panel,
using the Flat Washers (H-G), Spring Washers (H-F) and 2" Long Bolts (H-E). Do not
fully tighten until after next step. (see Detail A).
3. Attach the Back Stretcher (H-C) to the Headboard Posts using the same Washers and
1-5/8" Long Bolts (H-D) as in previous step.
4. Tighten all Bolts using the Allen Wrench (H-H). (see Detail A & B).
Gently lean the back of the assembled Headboard against the wall where the Bed will be
located in the room.
Harbor Hill
Bedroom
Assembly Instructions
Made in Viet Nam
email: [e-mail]
FURNITURE
Riverside

Page 4 of 7
Harbor Hill
Bedroom
Assembly Instructions
Made in Viet Nam
email: [e-mail]
FURNITURE
Riverside
ASSEMBLY STEPS :
1. Remove both drawers from the Storage Footboard. Refer to the steps above.
2. Place the Storage Footboard (F-A) face down on a clean and soft surface.
3. Attach the Drawer Box Support Legs (F-C) using the Flat Washers (F-H), Spring
Washers (F-G) and Bolts (F-F). Tighten with the Allen Wrench (F-I).
To remove the drawer:
A. Pull the drawer fully open so the
black latch is visible in the inside
channel of the guides.
B. Release the latches by
simultaneously pushing one lever up
and the other down.
C. At the same time, pulling the
drawer forward until the slides
release.
Page 4 of 7
Harbor Hill
Bedroom
Assembly Instructions
Made in Viet Nam
email: [e-mail]
FURNITURE
Riverside
ASSEMBLY STEPS :
1. Remove both drawers from the Storage Footboard. Refer to the steps above.
2. Place the Storage Footboard (F-A) face down on a clean and soft surface.
3. Attach the Drawer Box Support Legs (F-C) using the Flat Washers (F-H), Spring
Washers (F-G) and Bolts (F-F). Tighten with the Allen Wrench (F-I).
To remove the drawer:
A. Pull the drawer fully open so the
black latch is visible in the inside
channel of the guides.
B. Release the latches by
simultaneously pushing one lever up
and the other down.
C. At the same time, pulling the
drawer forward until the slides
release.

Page 5 of 7
Harbor Hill
Bedroom
Assembly Instructions
Made in Viet Nam
email: [e-mail]
FURNITURE
Riverside
ASSEMBLY STEPS :
To prevent possible damage to furniture and personal injury, it is recommended that two people are used to
perform the following steps.
5. Install two All-Thread Bolts (R-B) into the metal threaded inserts installed in the Headboard Posts and into
the metal inserts on the Storage Footboard.
6. Carefully position one end of one Bed Rail (R-A) onto the All-thread Bolts on the Headboard and connect
using the Arc Washers (R-F), Flat Washers (R-E), Spring Washers (R-D), and Hex Nut (R-C). Only partially
tighten the Nuts until the Footboard has been connected. Repeat for other Bed Rail.
7. Position and connect the Storage Footboard (F-A) to the other end of the Bed Rails, attaching as in the
previous Steps.
8. Carefully align the Storage Footboard to be 'square' with the Headboard. Using the Open Wrench (R-G)
tighten all Hex Nuts attaching the Side Rails to the Headboard and Storage Footboard. (See Detail E ).
9. Attach the six Support Legs (F-D) to the bottom side of three Wood Support Panels with Blocks (F-E). The
Panel Support Legs must be installed into the 6" x 6" x 1/2" blocks mounted on the bottom side of the
panels. (See Detail F). The Support Panel (F-K) used above the drawer compartment does not have a
support leg.
10. Position and attach the Support Panels to the Bed Rails using the Wood Screws (F-J) and your Phillips
Screwdriver.
The levelers located at the bottom of the Support Legs can be adjusted if necessary to support the panels.
11. Reinstall the Drawers into the Footboard by aligning the metal channels of the guides and push back into
the Footboard.
3 pcs.

Riverside
email: [e-mail]
#25780
King Size Headboard
The Headboard may be used alone with
an Eastern or California King Size
Metal Bed Frame
Page 7 of 7
25780 -- 6/0-6/6 Panel Headboard
25774 -- 5/0-6/6 Storage Bed Rails
or---25782 --6/0 Storage Bed Rails
25783 -- 6/0-6/6 Storage Footboard w/Platform
25780 -- 6/0-6/6 Panel Headboard
25772 -- 5/0-6/6 Panel Bed Rails
or--25784--6/0 Panel Bed Rails
25781 -- 6/0-6/6 Panel Footboard w/Slats
USE THESE HOLES FOR ATTACHING A CALIFORNIA
KING SIZE (6/0) METAL BED FRAME
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
CUSTOMER TO PROVIDE 5/16 X 1-1/2" LONG BOLTS, NUTS
& WASHERS TO CONNECT THE METAL BED FRAME
USE THESE HOLES FOR ATTACHING WOOD SIDE RAILS.
ALL HARDWARE IS INCLUDED WITH THE SIDE RAILS
USE THESE HOLES FOR ATTACHING AN EASTERN KING SIZE (6/6)
METAL BED FRAME
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
CUSTOMER TO PROVIDE 5/16 X 3-1/2" LONG BOLTS, NUTS &
WASHERS TO CONNECT THE METAL BED FRAME
QUEEN / EASTERN
KING RAILS
CALIFORNIA
KING RAILS
Riverside
email: [e-mail]
#25780
King Size Headboard
The Headboard may be used alone with
an Eastern or California King Size
Metal Bed Frame
Page 7 of 7
25780 -- 6/0-6/6 Panel Headboard
25774 -- 5/0-6/6 Storage Bed Rails
or---25782 --6/0 Storage Bed Rails
25783 -- 6/0-6/6 Storage Footboard w/Platform
25780 -- 6/0-6/6 Panel Headboard
25772 -- 5/0-6/6 Panel Bed Rails
or--25784--6/0 Panel Bed Rails
25781 -- 6/0-6/6 Panel Footboard w/Slats
USE THESE HOLES FOR ATTACHING A CALIFORNIA
KING SIZE (6/0) METAL BED FRAME
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
CUSTOMER TO PROVIDE 5/16 X 1-1/2" LONG BOLTS, NUTS
& WASHERS TO CONNECT THE METAL BED FRAME
USE THESE HOLES FOR ATTACHING WOOD SIDE RAILS.
ALL HARDWARE IS INCLUDED WITH THE SIDE RAILS
USE THESE HOLES FOR ATTACHING AN EASTERN KING SIZE (6/6)
METAL BED FRAME
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
CUSTOMER TO PROVIDE 5/16 X 3-1/2" LONG BOLTS, NUTS &
WASHERS TO CONNECT THE METAL BED FRAME
QUEEN / EASTERN
KING RAILS
CALIFORNIA
KING RAILS

Riverside
email: [e-mail]
#25785 Leather
King Size Headboard
The Headboard may be used alone with
an Eastern or California King Size
Metal Bed Frame
Page 7 of 7
25785 -- 6/0-6/6 Leather Panel Headboard
25774 -- 5/0-6/6 Storage Bed Rails
or---25782 --6/0 Storage Bed Rails
25783 -- 6/0-6/6 Storage Footboard w/Platform
25785 -- 6/0-6/6 Leather Panel Headboard
25772 -- 5/0-6/6 Panel Bed Rails
or--25784--6/0 Panel Bed Rails
25781 -- 6/0-6/6 Panel Footboard w/Slats
USE THESE HOLES FOR ATTACHING A CALIFORNIA
KING SIZE (6/0) METAL BED FRAME
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
CUSTOMER TO PROVIDE 5/16 X 1-1/2" LONG BOLTS, NUTS
& WASHERS TO CONNECT THE METAL BED FRAME
USE THESE HOLES FOR ATTACHING WOOD SIDE RAILS.
ALL HARDWARE IS INCLUDED WITH THE SIDE RAILS
USE THESE HOLES FOR ATTACHING AN EASTERN KING SIZE (6/6)
METAL BED FRAME
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
CUSTOMER TO PROVIDE 5/16 X 3-1/2" LONG BOLTS, NUTS &
WASHERS TO CONNECT THE METAL BED FRAME
QUEEN / EASTERN
KING RAILS
CALIFORNIA
KING RAILS
Riverside
email: [e-mail]
#25785 Leather
King Size Headboard
The Headboard may be used alone with
an Eastern or California King Size
Metal Bed Frame
Page 7 of 7
25785 -- 6/0-6/6 Leather Panel Headboard
25774 -- 5/0-6/6 Storage Bed Rails
or---25782 --6/0 Storage Bed Rails
25783 -- 6/0-6/6 Storage Footboard w/Platform
25785 -- 6/0-6/6 Leather Panel Headboard
25772 -- 5/0-6/6 Panel Bed Rails
or--25784--6/0 Panel Bed Rails
25781 -- 6/0-6/6 Panel Footboard w/Slats
USE THESE HOLES FOR ATTACHING A CALIFORNIA
KING SIZE (6/0) METAL BED FRAME
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
CUSTOMER TO PROVIDE 5/16 X 1-1/2" LONG BOLTS, NUTS
& WASHERS TO CONNECT THE METAL BED FRAME
USE THESE HOLES FOR ATTACHING WOOD SIDE RAILS.
ALL HARDWARE IS INCLUDED WITH THE SIDE RAILS
USE THESE HOLES FOR ATTACHING AN EASTERN KING SIZE (6/6)
METAL BED FRAME
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
CUSTOMER TO PROVIDE 5/16 X 3-1/2" LONG BOLTS, NUTS &
WASHERS TO CONNECT THE METAL BED FRAME
QUEEN / EASTERN
KING RAILS
CALIFORNIA
KING RAILS