RKC INSTRUMENT CB103 Manual

IMCB12-E2
CB103/CB403
CB903
Initial Setting Manual
RKC INSTRUMENT INC.
®
Digital Controller

IMCB12-E2 i - 1
Thank you for purchasing the RKC product.
Before operating this instrument, please carefully read this manual and fully understand its contents.
And always keep it around you to make it available easily anytime.
SYMBOL
: This mark is used when careful operation or handling is especially needed.
: This mark is used when a supplemental description of operation or handling is
needed.
: This mark is used when detailed or related information needs to be referred to.
z
If failure or error of this instrument could result in a critical accident of the
system, install an external protection circuit to prevent such an accident.
z
Do not turn on the power supply until all of the wiring is completed.
Otherwise electric shock, fire or malfunction may result.
z
Use this instrument within the scope of its specifications. Otherwise fire or
malfunction may result.
z
Do not use this instrument in the places subject to flammable or explosive
gas.
z
Do not touch high-voltage blocks such as power supply terminals, etc.
Otherwise electric shock may result.
z
Never disassemble, repair or modify the instrument. This may cause electric
shock, fire or malfunction.
CAUTION
: If there are possible dangers such as electric shock, fire (burns), etc. which may
result in operator's loss of life or injury, precautions to avoid such dangers are
described.
: In case instrument damages may be caused if operating procedures are not
strictly followed, precautions to avoid such damages are described.
: This mark is used when great care is needed especially for safety.
WARNING
!
WARNING
!

IMCB12-E2
i - 2
zThis is a Class A instrument. In a domestic environment this instrument may cause radio
interference, in which case the user is required to take adequate measures.
zThis instrument is protected from electric shock by reinforced insulation.
So please arrange reinforced insulation to the wire for input signal against the wires for
instrument power supply, source of power and loads as far as possible.
zThis instrument is manufactured on the assumption that it is used in the condition of being
mounted on the instrumentation panel. Therefore, take the necessary measures on the
equipment side mounted with this instrument so that the operator or other personnel are
not accessible to high-voltage blocks in this instrument such as power supply terminals,
etc.
zAlways observe precautions described in this manual. Otherwise serious injury or
accident may result.
zConduct all of the wiring in accordance with the local codes and regulations.
zInstall a protection device such as a fuse, etc. in the power supply, input or output line, if
necessary.
zDo not allow metal fragments or lead wire scraps to fall inside this instrument. This may
cause electric shock, fire or malfunction.
zFirmly tighten each terminal screw at the specified torque. Otherwise electric shock or fire
may result.
zDo not place any obstacle around this instrument in order not to impede radiation of heat.
And do not close ventilation holes.
zDo not connect wires to unused terminals.
zBefore cleaning the instrument, always turn off the power supply.
zRemove stains from this instrument using a soft, dry cloth. Do not use a volatile solvent
such as thinner in order to avoid deformation or discoloration.
zDo not rub nor strike the display unit of this instrument with a hard object.
NOTICE
zThis manual is written for RKC service engineers or qualified technicians. This manual is also
prepared especially for readers who already have a fundamental knowledge of electricity, control,
computer and communication.
zThis manual is subject to change without prior notice.
zExamples of figures, diagrams and numeric values used in this manual are for a better
understanding of the text, but not for assuring the resultant operation.
zThis manual may not be reproduced or copied in whole or in part without RKC's prior consent.
zRKC assumes no responsibility for any of the following damage which the user or third party may
suffer.
•Damage incurred as a result of using this product.
•Damage caused by product failure which cannot be predicted by RKC.
•Other indirect damage.
zIn order to use this instrument continuously and safely, periodic maintenance is required. Some of
components and parts used in this instrument have a limited service life, or deteriorate over time.
zThis manual is carefully prepared. However, if any mistake or omission is found, please contact
RKC.
CAUTION

IMCB12-E2 i - 3
CONTENTS
Page
1. TRANSFER TO MODE.........................................................1
1.1 Transfer to Initialization Mode.........................................................................1
1.2 End of Initialization Mode................................................................................3
2. SETTING...............................................................................4
2.1 Display Flowcharts Initialization Mode............................................................4
2.2 Procedure for Setting Each Parameter...........................................................5
2.3 List of Parameter in Initialization Code (Cod=0) .............................................7
2.4 List of Parameter in Initialization Code (Cod=1) ...........................................15
2.5 List of Parameter in Initialization Code (Cod=2) ...........................................23

IMCB12-E2 1
1. TRANSFER TO MODE
Initialization is to set parameters relating to instrument specifications (input type, input range, alarm
type, etc.) and those relating to instrument characteristics (setting limiter, alarm differential gap, etc.).
1.1 Transfer to Initialization Mode
The section in each picture is dimly lit.
1. Turn on the power to this instrument. Thus, the input type, input range and PV/SV display
mode change in this order.
2. Press the SET key for two seconds with the instrument set to PV/SV display mode to change the
instrument to parameter setting mode.
For details on parameter setting mode, see the instruction manual for CB103/CB403/
CB903 (IMCB11-E

).
3. Press the SET key to change to the set data lock function display (LCK).
4. Press the <R/S key to light brightly the thousands digit on the set value (SV) display unit.
5. Press the UP key to change 0to 1in the thousands digit.
Continued on the next page.
R/S
SET
PV
SV
OUT1 ALM1 ALM2DOAT
STEP
Set data lock function display
Set value
0 : Initialization mode locked
1 : Initialization mode
unlocked
R/S
SET
PV
SV
OUT1 ALM1 ALM2DOAT
STEP
Set data lock function display

1. TRANSFER TO MODE
IMCB12-E2
2
6. Press the SET key to change to the next parameter. Thus, the data in initialization mode is
unlocked.
The parameter to be displayed varies depending on the specification.
7. Press the <R/S key while pressing the SET key for two seconds to change the instrument to
initialization mode. Thus, the symbol (Cod) for selecting the initialize code is displayed first.
R/S
SET
PV
SV
OUT1 ALM1 ALM2DO
z
AT
STEP
CT1 input value display
R/S
SET
PV
SV
OUT1 ALM1 ALM2DOAT
STEP
Initialize code selection
display of initialization mode
R/S
SET
PV
SV
OUT1 ALM1 ALM2DO
z
AT
STEP
CT1 input value display

1. TRANSFER TO MODE
IMCB12-E2 3
1.2 End of Initialization Mode
If the setting is changed, always check all of the set values (SV setting mode, parameter
setting mode).
The section in each picture is dimly lit.
1. Transfer to Initialize code selection after each parameter is set.
2. Press the <R/S key while pressing the SET key for two seconds in the Initialize code selection
state to transfer to PV/SV display mode.
3. Press the SET key for two seconds in the PV/SV display mode state to transfer to parameter
setting mode.
4. Press the SET key to transfer to the set data lock function display (LCK).
5. Press the <R/S key to brightly light the thousands digit on the set value (SV) display unit.
See 4. on P. 1.
6. Press the DOWN key to set the numeric value corresponding to the thousands digit to 0 from 1.
7. Press the SET key to transfer to the next parameter. As a result, the Initialization mode lock
state setting becomes effective.
The parameter to be displayed varies depending on the specification.
R/S
SET
PV
SV
OUT1 ALM1 ALM2DO
z
AT
STEP
CT1 input value display
R/S
SET
PV
SV
OUT1 ALM1 ALM2DOAT
STEP
Set data lock function display
Set value
0 : Initialization mode locked
1 : Initialization mode
unlocked

4
IMCB12-E2
2. SETTING
2.1 Display Flowcharts in Initialization Mode
If the instrument is changed to initialization mode, the symbol (Cod) for selecting the initialize code is
displayed first. Initializing items are classified into 3 initialize code groups in initialization mode.
There are parameters which are not displayed depending on the specification.
Press the <R/S key while pressing the SET
key for two seconds.
Parameter setting modePV/SV display mode
Press the SET key
for two seconds.
Explaining the arrow mark : Press the SET key Initialize code selection (Cod)
(SL1)
(SL2)
(SL3)
(SL4)
Press the <R/S key while pressing the SET key for two
seconds with the set data unlocked.
(SL5)
(SL6)
(SL7)
(SL8)
Initialize code selection
(SL9)
(SL10)SV alarm type selection
(SLH)
(SLL)
Option selection
(STIK)
(STPK)
(STTM)
(dF)
(CTr)
(AH3)
(AH2)
(AH1)
(oH)
(PGdP)
(TCJ)
(SL12)
Special specification
selection 3
Special specification
selection 2
Energized/de-energized,
special specification selection
(WTH)
(WTL)
Engineering unit selection
Contact input selection
Third alarm special
specification selection
Third alarm type selection,
hold action selection
Direct/reverse action, control
output type selection
Second alarm type selection,
hold action selection
First alarm type selection,
hold action selection
(SL11)
HBA selection,
LBA selection, etc.
Factor to calculate
integral time
Factor to calculate
proportional band
Time factor assumed to
be safe
Digital filter setting
CT ratio setting
Third alarm
differential gap setting
Second alarm
differential gap setting
First alarm
differential gap setting
ON/OFF action
differential gap setting
Decimal point position
setting
Input type selection
Parameters in this initialize code are
only displayed.
Operating time display
[lower digits]
Operating time display
[upper digits]
Holding peak ambient
temperature
Setting limiter [low limit]
Setting limiter [high limit]
Set Cod to 2.Set Cod to 1.Set Cod to 0.
Auxiliar
y
out
p
ut selection
(SL13)
(SL15)
(SL14)

2. SETTING
IMCB12-E2 5
2.2 Procedure for Setting Each Parameter
[Example of changing the setting]
When the display unit shows SL1 (Input type selection) in initialize code 0, the following procedure is
for changing the input type from K to J.
The section in each picture is dimly lit.
1. Change the instrument to the initialize code selection display.
See 1.1 Transfer to Initialization Mode on page 1.
2. As SL1 belongs to the group of initialize code 0, do not change the initialize code (the units
digit) but press the SET key to change to SL1.
Continued on the next page.
R/S
SET
PV
SV
OUT1 ALM1 ALM2DOAT
STEP
Initialize code selection display
Input type selection
R/S
SET
PV
SV
OUT1 ALM1 ALM2DOAT
STEP
Initialize code selection display
R/S
SET
PV
SV
OUT1 ALM1 ALM2DOAT
STEP

2. SETTING
IMCB12-E2
6
3. Press the UP key to enter 1in the units digit of the set value (SV) display unit.
4. Press the SET key to change to the next parameter. Thus, the set value is registered.
If the initialize code is set to 1or 2, enter 1or 2in the units digits of the set value (SV)
display unit by pressing UP or DOWN key.
If the set value corresponds to any digit other than the units digit, press the shift key to move
the brightly lit digit. The brightly lit digit moves as follows every time the shift key is
pressed.




0 0 0 0
000
0
00
1
1
K
J
L
Input type Set value
Input type selection
R/S
SET
PV
SV
OUT1 ALM1 ALM2DOAT
STEP
Engineering unit setting
R/S
SET
PV
SV
OUT1 ALM1 ALM2DOAT
STEP