RKC INSTRUMENT CB100L Manual

IMCB10-E1
Limit Controller
CB100L/CB900L
Initial Setting Manual
RKC INSTRUMENT INC.
®

All Rights Reserved, Copyright 1998, RKC INSTRUMENT INC.

CAUTIONS

zThis manual is subject to change without prior notice.
zExamples of figures, diagrams and numeric values used in this manual are for a better understanding
of the text, but not for assuring the resultant operation.
zThis manual may not be reproduced or copied in whole or in part without RKC's prior consent.
zThis instrument and manual are manufactured, prepared, then shipped under strict quality control.
However, if any defect is found, please contact your nearest RKC sales office or agent from which you
bought the system.
zRKC assumes no responsibility for any of the following damage which the user or third party may
suffer.
(1) Damage incurred as a result of using this product.
(2) Damage caused by product failure which cannot be predicted by RKC.
(3) Other indirect damage.

IMCB10-E1 i - 1
INTRODUCTION
Before using this instrument, please carefully read this manual for its correct use. In addition, after
reading the manual keep it available easily anytime.
USERS OF THIS MANUAL
This manual is written mainly for personnel who have a fundamental knowledge of electricity as well
as control. This manual is also written for RKC service engineers or qualified technicians.
WIRING PRECAUTIONS
• If failure or error of this instrument could result in a critical accident of the system,
install an external protection circuit to prevent such an accident.
• In order to prevent instrument damage or failure, protect the power line and the
input/output lines from high currents by using fuses with appropriate ratings.
POWER SUPPLY
• In order to prevent instrument damage or failure, supply power of the specified rating.
• In order to prevent electric shock or instrument failure, do not turn on the power
supply until all of the wiring is completed.
NEVER USE THE INSTRUMENT NEAR FLAMMABLE GASES.
In order to prevent fire, explosion or instrument damage, never use this instrument at a
location where flammable or explosive gases or vapor exist.
NEVER TOUCH THE INSIDE OF THE INSTRUMENT.
In order to prevent electric shock or burns, never touch the inside of the instrument.
Only RKC service engineers can touch the inside of the instrument to check the circuit
or to replace parts. High voltage and high temperature sections inside the instrument
are extremely dangerous.
NEVER MODIFY THE INSTRUMENT.
In order to prevent accident or instrument failure, never modify the instrument.
MAINTENANCE
• In order to prevent electric shock, burns or instrument failure, only RKC service
engineers may replace parts.
• In order to use this instrument continuously and safely, conduct periodic
maintenance. Some parts used in this instrument have a limited service life and may
deteriorate over time.
WARNING
!

IMCB10-E1
i - 2
INSTRUMENT SAFETY CAUTIONS
zThis instrument is designed to be mounted on instrumentation panels. It is therefore manufactured
as part of the final product to facilitate wiring. This means that unauthorized personnel can easily
access the high-voltage sections in this instrument such as power terminals, etc. Therefore, when
this instrument is installed on the final product, the user should take the necessary measures for the
final product to ensure that unauthorized personnel cannot access the high-voltage sections, etc.
zIn order to use this instrument correctly and safely, always observe the cautions described in this
manual when performing operations and maintenance. RKC assumes no responsibility for any
injury or accident resulting from not following these cautions.
NOTES ON INDICATIONS
The following indications are used in this manual to ensure the safe, correct use of the
CB100L/CB900L.
SIGNAL WORDS
SYMBOL MARKS
CAUTIONS PRIOR TO USE
zThis instrument is intended to be used under the following environmental conditions. (IEC1010)
[OVERVOLTAGE CATEGORY II, POLLUTION DEGREE 2]
zTo the instrument with power supply of 24V, please be sure to supply the power from SELV
circuit.
zBefore cleaning the instrument, check that the power is turned off.
zRemove stains on the display unit using a soft cloth or tissue paper.
zAs the display unit is easily scratched, do not scrub or touch it with a hard object.
zThe stains on the housing shall be wiped off by the cloth which is dipped into the neutral cleanser
diluted by water and wrung tightly, and finish it by a dried cloth.
This is a Class A (EN55022) instrument. In a domestic environment this
instrument may cause radio interference, in which case the user is required
to take adequate measures.
WARNING : Where there are possible dangers such as electric shock, fire(burns), etc. Which
could cause loss of life or injury, precautions to avoid such dangers are
: These describe precautions to be taken in case unit damage may result if
operating procedures are not strictly followed.
NOTE :Extra noted or precautions are added to operating procedures and explanations.
CAUTION
: This mark is used when great care is needed especially for safety.
!
∗
∗∗
∗: This mark is used to add extra notes, precautions or supplementary
explanations to table and figures.
CE CONFORMED INSTRUMENT CAUTIONS
zThis instrument is protected from electric shock by reinforced insulation. So please arrange
reinforced insulation to the wire for input signal against the wires for instrument power
supply, source of power and loads as far as possible.
zEN55022, EN50082-2 and EN61010-1 are applicable to this instrument.
WARNING
!

IMCB10-E1 i - 3
Name and number of this instruction manual :
Name : Limit Controller CB100L/CB900L Initial Setting Manual
Manual number : IMCB10-E1


Revisions
Date of revision Manual number Reason for revision
October 5, 1998 IMCB10-E1 The first edition issue

IMCB10-E1
i - 4
CONTENTS
1. TRANSFER TO MODE ...................................................................... 1
1.1 Transfer to initialization mode..........................................................................1
1.2 End of initialization mode.................................................................................3
2. PROCEDURE FOR SETTING............................................................ 4
2.1 Display flowcharts in initialization mode...........................................................4
2.2 Procedure for setting each parameter .............................................................5
2.3 Details of parameters in initialize code 0(Cod=0) ............................................7
2.4 Details of parameters in initialize code 1 (Cod=1) .........................................12
2.5 Details of parameters in initialize code 2 (Cod=2) .........................................18
3. COMMUNICATION INITIALIZE IDENTIFIER................................... 19
List of communication initialize identifiers .........................................................19

1.TRANSFER TO MODE
IMCB10-E1 1
1. TRANSFER TO MODE
Initialization is to set parameters relating to instrument specifications (input type, input range, alarm
type, etc.) and those relating to instrument characteristics (setting limiter, alarm differential gap, etc.).
1.1 Transfer to initialization mode
cTurn on the power to this instrument. Thus, the input type, input range and PV/SV display mode
(PV/SV display) change in this order.
dPress the SET key for 2 sec with the instrument set to PV/SV display mode to change the
instrument to parameter setting mode.
*For details on parameter setting mode, see the CB100L/CB900L Instruction Manual.
[IMCB08-E]
ePress the SET key to change to the set data lock function display screen.
fPress the <RST key to light brightly the thousands digit on the set value (SV) display unit.
gPress the UP key to change "0" to "1" in the thousands digit.
RST
RSTRST
RST
SET
SETSET
SET
SV
SVSV
SV
PV
PVPV
PV
ALM2
ALM1
OUT
EXCD
RST
RSTRST
RST
SET
SETSET
SET
SV
SVSV
SV
PV
PVPV
PV
ALM2
ALM1
OUT
EXCD
Set data lock function
Bright lighting :
Dim lighting :
As the units digit light brightly first,
press the <RST key to light brightly
the thousands digit.
Set data lock function
Set value
0 : Initialization mode locked
1 : Initialization mode unlocked
Bright lighting :
Dim lighting :

1. TRANSFER TO MODE
2IMCB10-E1
hPress the SET key to change to the next parameter. Thus, the data in initialization mode is
unlocked.
*In the above figure, the alarm 1 (ALM1) setting value is displayed. However, the parameter to be
displayed varies depending on the specification.
iKeep pressing both the SET and <RST keys for 2 sec to change the instrument to initialization
mode. Thus, the symbol (Cod) for initialize code selection is displayed first.
zThe initialization mode can be selected anytime when PV/SV, SV setting, peak hold value, or
over time is displayed.
zIf the controller is change to initialization mode, both limit and alarm outputs contact are set to
the open state, and the analog output, to -5 %.
RST
RSTRST
RST
SET
SETSET
SET
SV
SVSV
SV
PV
PVPV
PV
ALM2
ALM1
OUT
EXCD
RST
RSTRST
RST
SET
SETSET
SET
SV
SVSV
SV
PV
PVPV
PV
ALM2
ALM1
OUT
EXCD
RST
RSTRST
RST
SET
SETSET
SET
SV
SVSV
SV
PV
PVPV
PV
ALM2
ALM1
OUT
EXCD
Alarm 1 setting value
Alarm 1 setting value
Initialize code selection in
initialization mode
Bright lighting :
Dim lighting :
NOTES

1. TRANSFER TO MODE
IMCB10-E1 3
1.2 End of initialization mode
cTransfer to "initialize code selection" after each parameter is set.
dSimultaneously keep pressing both the SET and <RST keys for 2 sec in the "Initialize code
selection" state to transfer to "PV/SV display mode."
ePress the SET key for 2 sec in the "PV/SV display mode" state to transfer to parameter setting
mode.
fPress the SET key to transfer to the set data lock function display.
gPress the <RST key to brightly light the thousands digit on the set value (SV) display unit.
(See fon P.1)
hPress the DOWN key to set the numeric value corresponding to the thousands digit to "0" from "1."
iPress the SET key to transfer to the next parameter. As a result, the "Initialization mode lock state"
setting becomes effective.
After the controller terminates the initialization mode, the limit action output is set to
the ON state in the same way as at the time of power ON.
RST
RSTRST
RST
SET
SETSET
SET
SV
SVSV
SV
PV
PVPV
PV
ALM2
ALM1
OUT
EXCD
RST
RSTRST
RST
SET
SETSET
SET
SV
SVSV
SV
PV
PVPV
PV
ALM2
ALM1
OUT
EXCD
Set data lock function
Set value
0 : Initialization mode locked
1 : Initialization mode unlocked
Bright lighting :
Dim lighting :
Alarm 1 setting value
*In the left figure, the alarm 1 setting value is displayed.
However, the parameter to be displayed varies
depending on the specification.
NOTE

2.PROCEDURE FOR SETTING
4IMCB10-E1
2. PROCEDURE FOR SETTING
If the instrument is changed to initialization mode, the symbol (Cod) for selecting the initialize code is
displayed first. (Initializing items are classified into 3 initialize code groups in initialization mode.)
Enter the initialize code corresponding to the parameter to be chanted, and then select the parameter
to be changed by pressing the SET key. The measured value (PV) display unit shows the characters
corresponding to the parameter, and the set value (SV) display unit shows the value corresponding to
that parameter. Display flowcharts in initialization mode are shown in the following.
2.1 Display flowcharts in initialization mode
There are parameters which are not displayed depending on the
specification.
PV/SV display mode
(SL1)
Parameter setting mode Communication setting mode
Keep pressing the SET and <RST keys simultaneously
for 2 sec with the set data unlocked.
Explaining the arrow mark :
Press the SET and <RST keys
simultaneously for 2 sec.
Press the SET key.
Set to0.
Input type selection
Engineering unit
selection
A
ction selection at the
time of reset key
operation
Alarm 1 type selection
Alarm 2 type selection
Limit action type
selection
Special specification
selection 1
Special specification
selection 2
Unused
Option selection
For manufacturer's
[RKC's] own use
Setting limiter
[high limit]
Setting limiter
[low limit]
Setting the position of
decimal point
Differential gap setting
of alarm 1 (ALM1)
Differential gap setting
of alarm 2 (ALM2)
Holding peak ambient
temperature
Operating time display
unit (Upper digits)
Operating time display
unit (Lower digits)
Parameters in this initialize code
are only displayed.
(SL2)
(SL3)
(SL4)
(SL5)
(SL6)
(SL7)
(SL8)
(SL9)
(SL10)
(SL11)
(SLH)
(SLL)
(PGdP)
(AH2)
(AH1)
(TCJ)
(WTH)
(WTL)
Initialize code selection
Initialize code selection
Set to1. Set to2.
Press the SET key
for 2 sec.
Press the SET and <RST keys simultaneously.
CAUTION

2.PROCEDURE FOR SETTING
IMCB10-E1 5
2.2 Procedure for setting each parameter
[Example of changing the setting]
When the display unit shows "Limit action type selection (SL6)" in initialize code "0", the following
procedure is for changing the limit action type from "high limit action" to "low limit action."
cChange the instrument to the initialize code selection display.
(See "1.1 Transfer to initialization mode" on P. 1.)
dAs "Limit action type selection (SL6)" belongs to the group of initialize code "0", do not change
the initialize code (the units digit) but press the SET key to change to "SL6."
When the initialize code is set to "1" or "2", enter "1" or "2" in the units digit of the set value (SV)
display unit by pressing the UP or DOWN key.
RST
RSTRST
RST
SET
SETSET
SET
SV
SVSV
SV
PV
PVPV
PV
ALM2
ALM1
OUT
EXCD
RST
RSTRST
RST
SET
SETSET
SET
SV
SVSV
SV
PV
PVPV
PV
ALM2
ALM1
OUT
EXCD
RST
RSTRST
RST
SET
SETSET
SET
SV
SVSV
SV
PV
PVPV
PV
ALM2
ALM1
OUT
EXCD
Bright lighting :
Bright lighting :
Dim lighting :
Dim lighting :
Initialize code selection
NOTE Please read this NOTE without fail.
Limit action type selection
Initialize code selection

2.PROCEDURE FOR SETTING
IMCB10-E1
6
ePress the <RST key to move the brightly lit digit of the set value (SV) display unit to the hundreds
digit. The brightly lit digit moves as follows every time the <RST key is pressed.
fPress the UP key to enter "1" in the hundreds digit of the set value (SV) display unit.
gPress the SET key to change to the next parameter. Thus, the set value is registered.
RST
RSTRST
RST
SET
SETSET
SET
SV
SVSV
SV
PV
PVPV
PV
ALM2
ALM1
OUT
EXCD
RST
RSTRST
RST
SET
SETSET
SET
SV
SVSV
SV
PV
PVPV
PV
ALM2
ALM1
OUT
EXCD
Bright lighting :
Dim lighting :
Limit action type selection
Special specification selection 1
Set value
0 : Limit action (high limit)
1 : Limit action (low limit)

2.PROCEDURE FOR SETTING
IMCB10-E1 7
The details of parameters in each initialize code group are described in the following.
2.3 Details of parameters in initialize code 0 (Cod=0)
(1) SL1 (Input type selection)
Conduct the setting so that it matches the instrument specification (input type). If the
setting is changed, always re-set the setting limits (SLH and SLL). (See P.12, 13)
Factory set value varies depending on the input type.
Set value Input type
0000 K
0001 J
0010 L
0011 E
0100 N
0111 R
1000 S
1001 B
1010 W5Re/W26Re
1011 PLII
0101 T
0110 U
Thermocouple input
(TC)
1100 Pt100 Ω(JIS/IEC)
1101 JPt100 Ω(JIS)
RTD input
1110 0to5VDC
1110 0to10VDC *1 Voltageinput
1111 1to5VDC
1110 0to20mADC
1111 4to20mADC
Current input *2
*1 To be fixed to "1110" for the 0 to 10 V DC (Z-1010 specification). No input type cannot be
changed as the hardware differs.
*2 For the current input specification, a resistor of 250 Ωmust be connected between the input
terminals.
Parameter display position
CAUTION
Measured value (PV) display unit shows parameter No. (character).
Input the numerical value in the set value (SV) display unit.
*Note that the relevant digit used
differs depending on the parameter.
The figure at the above is for selects the "Limit action (low limit)" in "SL6 (Limit action type selection)."
Set value
0
1

2.PROCEDURE FOR SETTING
IMCB10-E1
8
SL2 (Engineering unit selection)
z
For the input type of "Voltage/current input," even if the unit is set, it is ineffective.
z
Any digits other than the units digit are not used. As malfunction may result, do not
change any of these digits.
Factory set value : "0000"
Set value Description
0°C Engineering unit selection
1°F
000 Fixed
(3) SL3 (Action selection at the time of reset key operation)
z
When the reset action is taken by communication or contact input, all data items (peak
hold value and over time) are cleared.
z
Key operation is effective only when PV, peak hold value or over time is displayed.
z
Any digits other than the units and tens digits are not used. As malfunction may result, do
not change any of these digits.
Factory set value : "0000"
Set value Description
0 0 Reset action taken and all data items cleared *1 Selects the action on
0 1 Reset action taken and each data items cleared *2 each screen at the
1 0 Reset action taken and each data items cleared *3 of reset key
1 1 Reset action taken and each data items cleared *4
0 0 Fixed
All data items : Peak hold value and over time
*1 : Possible in any case where PV, peak hold value, or over time is displayed.
*2 : The reset action can be taken only when PV or over time is displayed. The peak hold value can be
cleared only when it is displayed.
*3 : The reset actin can be taken only when PV or peak hold value is displayed. Over time can be
cleared only when it is displayed.
*4 : The reset action can be taken only when PV is displayed. The peak hold value can be cleared only
when it is displayed. Over time can be cleared only when it is displayed.
CAUTIONS
CAUTIONS

2.PROCEDURE FOR SETTING
IMCB10-E1 9
(4) SL4 (Alarm 1 type selection)
Instrument without the alarm 1 (ALM1) is set to "0000."
Factory set value varies depending on the instrument specification.
Set value Description
0 0 0 Alarm 1 (ALM1) not provided Alarm 1 (ALM1) type selection
0 0 1 Deviation high alarm
0 1 0 Deviation high/low alarm
0 1 1 Process high alarm
1 0 1 Deviation low alarm
1 1 0 Band alarm
1 1 1 Process low alarm
0 Without alarm hold action Alarm 1 (ALM1) with hold action
1 With alarm hold action selection
(5) SL5 (Alarm 2 type selection)
Instrument without the alarm 2 (ALM2) is set to "0000."
Factory set value varies depending on the instrument specification.
Set value Description
0 0 0 Alarm 2 (ALM2) not provided Alarm 2 (ALM2) type selection
0 0 1 Deviation high alarm
0 1 0 Deviation high/low alarm
0 1 1 Process high alarm
1 0 1 Deviation low alarm
1 1 0 Band alarm
1 1 1 Process low alarm
0 Without alarm hold action Alarm 2 (ALM2) with hold action
1 With alarm hold action selection
CAUTION
CAUTION

2.PROCEDURE FOR SETTING
IMCB10-E1
10
(6) SL6 (Limit action type selection)
The units digit is not used. As malfunction may result, do not change this digit.
Factory set value : "0000"
Set value Description
0Fixed
0 Limit action output turned ON at the time of power Selects the limit
1 Limit actin output turned OFF at the time of power ON action type and
0 Limit action (high limit) hold action
1 Limit action (low limit)
0 Without alarm hold action
1 With alarm hold action
(7) SL7 (Special specification selection 1)
Instrument without the alarm 1 (ALM1) and alarm 2 (ALM2) is set to "0000".
yInstrument without the alarm 1 (ALM1). [SL4 setting details : For "0000"]
yInstrument without the alarm 2 (ALM2). [SL5 setting details : For "0000"]
Factory set value : "1100"
Set value Description
0 Energize alarm Energize alarm/de-energize
1 De-energize alarm selection (Alarm 1 side)
0 Energize alarm Energize alarm/de-energize
1 De-energize alarm selection (Alarm 2 side)
0 Z-124 specification not provided *1 Special specification selection
1 Z-124 specification provided *2 (Alarm 1 side)
0 Z-124 specification not provided *1 Special specification selection
1 Z-124 specification provided *2 (Alarm 2 side)
*1 : The alarm output is forcibly turned ON when the burnout function is activated.
*2 : No alarm action is taken by the burnout function. (Same as the normal alarm action)
CAUTION
CAUTION

2.PROCEDURE FOR SETTING
IMCB10-E1 11
(8) SL8 (Special specification selection 2)
The thousands and hundreds digits are not used. As malfunction may result, do not
change these digits.
Factory set value : "0011"
Set value Description
0 Limit action output (Energized output) Selects limit action output
1 Limit action output (De-energized output) energized/de-energized.
0 See *1
1 See *2
0 0 Fixed
*1 : The limit action output is forcibly turned ON when the burnout function is activated.
*2 : The limit action output is normally energized even when the burnout function is activated.
(9) SL9 (Unused)
SL9 is not used. (Only displayed)
Displayed value : "0000" fixed
(10) SL10 (Option selection)
The thousands digit is not used. As malfunction may result, do not change this digit.
Factory set value varies depending on the instrument specification.
Set value Description
0 Analog output not provided Selection of analog output
1 Analog output provided function
0 Contact input not provided Selection of contact input
1 Contact input provided function
0 Communication function not provided Selection of communication
1 Communication function provided function
0Fixed
*When "Communication function provided" and "Contact input provided" are simultaneously selected,
this is judged to be "Contact input not provided."
CAUTION
CAUTION

2.PROCEDURE FOR SETTING
IMCB10-E1
12
(11) SL11 (For manufacturer's [RKC's] own use)
Do not change it, as it is used to adjust the instrument.
2.4 Details of parameters in initialize code 1 (Cod=1)
(1) SLH (Setting limiter [high limit] )
z
Set the limiter by referring to "Input range table" (P.15)
z
Limiter setting becomes SLH SLL.
Setting method
Press the <RST key to move the digit, then enter the high limit value of input range by pressing the
UP or DOWN key. The set value (SV) display unit shows the numeric value.
Factory set value varies depending on the instrument specification.
Input type Setting range
K 0 to 1372 °C (0 to 2502 °F)
J 0 to 1200 °C (0 to 2192 °F)
R 0 to 1769 °C (0 to 3216 °F)
S 0 to 1769 °C (0 to 3216 °F)
B 0 to 1820 °C (0 to 3308 °F)
E 0 to 1000 °C (0 to 1832 °F)
N 0 to 1300 °C (0 to 2372 °F)
T -199.9 to +400.0 °C (-199.9 to +752.0 °F)
W5Re/W26Re 0 to 2320 °C (0 to 4208 °F)
PL II 0 to 1390 °C (0 to 2534 °F)
U -199.9 to +600.0 °C (-199.9 to +999.9 °F)
Thermocouple
input (TC)
L 0 to 900 °C (0 to 1652 °F)
Pt100 Ω(JIS/IEC) *1 -199.9 to +649.0 °C (-199.9 to +999.9 °F)RTD input
JPt100 Ω(JIS) -199.9 to +649.0 °C (-199.9 to +999.9 °F)
0 to 5 V DC -1999 to +9999
Voltage input 0 to 10 V DC *2 (programmable scale)
1 to 5V DC
0 to 20 mA DC *3Current input
4 to 20 mA DC *3
-1999 to +9999
(programmable scale)
*1 : IEC (International Electrotechnical Commission) is equivalent to JIS, DIN and ANSI.
*2 : For the 0 to 10 V DC (Z-1010 specification), no input type cannot be changed as the hardware
differs.
*3 : For the current input specification, a resistor of 250 Ωmust be connected between the input
terminals.
CAUTION
CAUTIONS

2.PROCEDURE FOR SETTING
IMCB10-E1 13
(2) SLL (Setting limiter [low limit] )
z
Set the limiter by referring to "Input range table." (P.15)
z
Limiter setting becomes SLH SLL.
Setting method
Press the <RST key to move the digit, then enter the low limit value of input range by pressing the
UP or DOWN key.
The set value (SV) display unit shows the numeric value.
Factory set value varies depending on the instrument specification.
Input type Setting range
K 0 to 1372 °C (0 to 2502 °F)
J 0 to 1200 °C (0 to 2192 °F)
R 0 to 1769 °C (0 to 3216 °F)
S 0 to 1769 °C (0 to 3216 °F)
B 0 to 1820 °C (0 to 3308 °F)
E 0 to 1000 °C (0 to 1832 °F)
N 0 to 1300 °C (0 to 2372 °F)
T -199.9 to +400.0 °C (-199.9 to +752.0 °F)
W5Re/W26Re 0 to 2320 °C (0 to 4208 °F)
PL II 0 to 1390 °C (0 to 2534 °F)
U -199.9 to +600.0 °C (-199.9 to +999.9 °F)
Thermocouple
input (TC)
L 0 to 900 °C (0 to 1652 °F)
Pt100 Ω(JIS/IEC) *1 -199.9 to +649.0 °C (-199.9 to +999.9 °F)RTD input
JPt100 Ω(JIS) -199.9 to +649.0 °C (-199.9 to +999.9 °F)
0 to 5 V DC -1999 to +9999
Voltage input 0 to 10 V DC *2 (programmable scale)
1 to 5 V DC
0 to 20 mA DC *3Current input
4 to 20 mA DC *3
-1999 to +9999
(programmable scale)
*1 : IEC (International Electrotechnical Commission) is equivalent to JIS, DIN and ANSI.
*2 : For the 0 to 10 V DC (Z-1010 specification), no input type cannot be changed as the hardware
differs.
*3 : For the current input specification, a resistor of 250 Ωmust be connected between the input
terminals.
CAUTIONS

2.PROCEDURE FOR SETTING
IMCB10-E1
14


Input range table
c
cc
cThermocouple input
Type Input range Type Input range
K 0 to 200 °C B 400 to 1800 °C
K 0 to 400 °C B *1 0 to 1820 °C
K 0 to 600 °C B 800 to 3200 °F
K 0 to 800 °C B *1 0 to 3308 °F
K 0 to 1000 °C E 0 to 800 °C
K 0 to 1200 °C E 0 to 1000 °C
K 0 to 1372 °C E 0 to 1600 °F
K 0 to 100 °C E 0 to 1832 °F
K 0 to 300 °C N 0 to 1200 °C
K 0 to 450 °C N 0 to 1300 °C
K 0 to 500 °C N 0 to 2300 °F
K 0 to 800 °F N 0 to 2372 °F
K 0 to 1600 °F T *2 -199.9 to +400.0 °C
K 0 to 2502 °F T *2 -199.9 to +100.0 °C
K 20 to 70 °F T -100.0 to +200.0 °C
J 0 to 200 °C T 0.0 to 350.0 °C
J 0 to 400 °C T *2 -199.9 to +752.0 °F
J 0 to 600 °C T -100.0 to +200.0 °F
J 0 to 800 °C T -100.0 to +400.0 °F
J 0 to 1000 °C T 0.0 to 450.0 °F
J 0 to 1200 °C T 0.0 to 752.0 °F
J 0 to 450 °C W5Re/W26Re 0 to 2000 °C
J 0 to 800 °F W5Re/W26Re 0 to 2320 °C
J 0 to 1600 °F W5Re/W26Re 0 to 4000 °F
J 0 to 2192 °F PL II 0 to 1300 °C
J 0 to 400 °F PL II 0 to 1390 °C
J 0 to 300 °F PL II 0 to 1200 °C
R *1 0 to 1600 °C PL II 0 to 2400 °F
R *1 0 to 1769 °C PL II 0 to 2534 °F
R *1 0 to 1350 °C U *2 -199.9 to +600.0 °C
R *1 0 to 3200 °F U *2 -199.9 to +100.0 °C
R *1 0 to 3216 °F U *2 0.0 to 400.0 °C
S *1 0 to 1600 °C U *2 -199.9 to +999.9 °F
S *1 0 to 1769 °C U *2 -100.0 to +200.0°F
S *1 0 to 3200 °F U 0.0 to 999.9 °F
S *1 0 to 3216 °F Continued on the following page.