Robern YC2430D4P1L3 User manual

1
Part no. CB-209-1332 05/05/20
Vitality Cabinet
© 2020 Robern, Inc. 701 N. Wilson Ave. Bristol, PA 19007 U.S.A.
800.877.2376 www.robern.com
Installation instructions
VITALITY CABINET
SINGLE DOOR WITH SAFE SEAL™
Important safety instructions - Save these instructions
Model Numbers- 2
Safety- 3
Parts- 4
Dimensions- 5
Electric Connections - 7
Recess Mounting- 11
Surface Mounting- 13
Final Assembly- 16
Use and Maintenance- 17
Warranty- 18
This instruction sheet contains information on how to install the Vitality series cabinets. This series comes in various sizes. Refer to
specic model numbers for dimensions.
Read the specic instruction for how your cabinet will be mounted. The cabinets can be surface mounted or recess mounted.
Save these instructions for future use and reference. An improper installation voids the warranty. Installed cabinets cannot be returned.
If you experience any problems with your cabinet, contact your dealer or Robern directly.
Limited Warranty — One Year Term
CONTENTS
GENERAL INFORMATION
3000K:
YC2430D4P1L3, YC2440D4P1L3,
YC2430D4P1R3, YC2440D4P1R3

2
Part no. CB-209-1332 05/05/20
Vitality Cabinet
© 2020 Robern, Inc. 701 N. Wilson Ave. Bristol, PA 19007 U.S.A.
800.877.2376 www.robern.com
Installation instructions
MODEL NUMBERS
Use the chart below to build a Vitality Cabinet model number. This chart references the model number for a 24" W x 30" H x 4" D Vitality
cabinet. Consult the Robern Price Book for a complete list of model numbers. The model number is located inside of your cabinet.
Model Numbers
Product Y = Vitality
Category C = Cabinet
Width 24 = 23-1/4” (591 mm)
Height 30 = 30” (762 mm)
40 = 39-3/8" (1000mm)
Depth D4 = 4-5/8” (118 mm)
Door Style P1 = Single Door
Hinge Side L = Left
R = Right
Options 3 = 3000K
Y C 24 30 D4 P1 L3

3
Part no. CB-209-1332 05/05/20
Vitality Cabinet
© 2020 Robern, Inc. 701 N. Wilson Ave. Bristol, PA 19007 U.S.A.
800.877.2376 www.robern.com
Installation instructions
SAFETY
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical furnishing, basic precautions should always be followed, including
the following:
DANGER: Read all instructions before using this cabinet.
WARNING: To reduce the risk of burns, re, electric shock, or injury to persons:
Use this furnishing only for its intended use as described in these instructions.
Do not use attachments not recommended by the manufacturer. Never drop or insert any
object into any opening.
Do not use outdoors.
WARNING: Risk of electric shock. Connect this furnishing to a properly grounded cir-
cuit only. See Grounding instructions.
CAUTION: Maximum shelf load 34lbs/15.4kg
GROUNDING INSTRUCTIONS: This product must be connected to a ground-
ed metal, permanent wiring system, or an equipment-grounding conductor must be run with
the circuit conductors and connected to the equipment-grounding terminal or lead on the
product.
WARNING: Electrical option cabinet must be wired to a Class A 20 Amp GFCI (Ground
Fault Circuit Interrupter) protected circuit when used in bathrooms and all other locations
required by the National Electric Code.
SAVE THESE INSTRUCTIONS

4
Part no. CB-209-1332 05/05/20
Vitality Cabinet
© 2020 Robern, Inc. 701 N. Wilson Ave. Bristol, PA 19007 U.S.A.
800.877.2376 www.robern.com
Installation instructions
TOOLS NEEDED
PARTS
Depending on installation, not all parts will be used.
(1) Single Door Vitality Cabinet
(3) Glass Shelves
(30) MSMK30D4P, (40) MSMK40D4P
Optional for surface mounting
(2) Z Mounting Bars
(2) Glass Side Panel
[SS712]
(3) Top Clip
[SS676]
(12) #10 x 1/2 Screw
[SS672]
(12) Screw Cap
[SS674]
(6) #10 x 2" Screw
[203-1349]
(6) Wall Anchors
[SS131]
(16) Shelf Clip
[SS134]
(50 / 100) Hole Plug
[SS672]
(6) Screw Cap
[216-1096] Hardware Bag
[SS666]
(4) Hinge Clip
[SS674]
(6) #10 x 2" Screw

5
Part no. CB-209-1332 05/05/20
Vitality Cabinet
© 2020 Robern, Inc. 701 N. Wilson Ave. Bristol, PA 19007 U.S.A.
800.877.2376 www.robern.com
Installation instructions
DIMENSIONS
A
B
D
A
B
D
Isometric View Front ViewSide View
Wire Access Hole
Rough Opening (RO) for recessed installation in chart below
D1 = minimum 4“ required or 2X4 construction
Determine overall cabinet dimensions. If recessing cabinet, determine rough-in dimensions. See chart for specic model dimensions.
YC2430 YC2440
A23-1/4" (591 mm)
B30" (762 mm) 39-3/8" (1000 mm)
RO (A) 22-1/2" (571 mm)
RO (B) 29-1/4" (743 mm) 38-5/8" (981 mm)
D4-5/8" (118 mm)
D1 3-3/4" (95 mm)
7/8"
(23 mm)
5-3/4"
(146 mm)
9-1/2"
(248 mm)
14-3/8"
(365 mm)
D1

6
Part no. CB-209-1332 05/05/20
Vitality Cabinet
© 2020 Robern, Inc. 701 N. Wilson Ave. Bristol, PA 19007 U.S.A.
800.877.2376 www.robern.com
Installation instructions
REMOVING THE DOOR FOR EASE OF INSTALLATION
SECTION 2 - ELECTRIC CONNECTIONS
1. Unplug the door from the cabinet.
2. While supporting the door, pinch the release clip at the rear of each hinge, as shown. Set the door aside in a safe place.
NOTE: The cardboard sleeve attached to the door protects the edges of the door during installation.
21
CIRCUIT BREAKER
WHITE
GROUND
BLACK
WHITE
GROUND
BLACK
FIELD CONNECTION
120VAC
20A GFI
DIMMER
LINE/BLACK
LINE/RED
NEUTRAL/WHITE
NEUTRAL/WHITE
3
All wiring should be done by a qualied licensed electrician.
WARNING: To reduce the risk of electrical shock, shut off power before wiring the cabinet.
CAUTION: Required 120 VAC Class A 20 Amp GFI protected circuit.
CAUTION: This product must be connected to a grounded, metal permanent wiring system or an equipment-grounding conductor must
be run with the circuit conductors and connected to the equipment grounding terminal or lead on the product.
WARNING: An Electrical option cabinet must be wired to a Class A 20 Amp GFCI (Ground Fault Circuit Interrupter) protected circuit
when used in bathrooms and all other locations required by the National Electric Code.
3. Make eld connections as per wiring diagram for the electrical option being installed.

7
Part no. CB-209-1332 05/05/20
Vitality Cabinet
© 2020 Robern, Inc. 701 N. Wilson Ave. Bristol, PA 19007 U.S.A.
800.877.2376 www.robern.com
Installation instructions
ELECTRIC CONNECTIONS
OR
Option 1 Option 2
TWO options for cabinet wiring are available. Select the best option to make your installation easier.
Option 1: Connecting the FIELD/POWER wires at the rear of the cabinet.
Option 2: Connecting the FIELD/POWER wires inside the cabinet.
Removing the electronic shelf cover inside the cabinet allows the FIELD/POWER wires to be connected inside the cabinet. Removal of
the interior electrical shelf cover is required. The cabinet can be fully wired after mounting in/on the wall.

8
Part no. CB-209-1332 05/05/20
Vitality Cabinet
© 2020 Robern, Inc. 701 N. Wilson Ave. Bristol, PA 19007 U.S.A.
800.877.2376 www.robern.com
Installation instructions
1. Remove the access screws from each plate located on the back of the cabinet. Remove rear plates to access internal wiring.
NOTE: Wiring access opening closest to hinge side of cabinet contains dimmer/switch connections.
2. Carefully cut plastic tie before making the connections.
3. Feed the electric wire through the access hole in the plate as shown.
4. Make all electrical connections as referenced in the electrical diagram on page 6.
5. Reinstall rear access plate.
31 2
5
4" MAX
102 mm MAX
OPTION 1 - ELECTRIC CONNECTIONS

9
Part no. CB-209-1332 05/05/20
Vitality Cabinet
© 2020 Robern, Inc. 701 N. Wilson Ave. Bristol, PA 19007 U.S.A.
800.877.2376 www.robern.com
Installation instructions
OPTION 2 - ELECTRIC CONNECTIONS
1. Remove the access screws in bottom of the electrical shelf (all instances). Lift up and remove for access to electrical connections.
NOTE: Wiring access opening closest to hinge side of cabinet contains dimmer/switch connections.
2. Carefully cut plastic ties before making the connections.
3. Feed the eld wiring through the access holes in the back of the cabinet.
4. Make all electrical connections as referenced in the electrical diagram on page 6.
5. Engage top of electrical shelf into back raceway and rotate down to close, making sure not to crimp or pinch wires and connections.
6. Reinstall two access screws into electrical shelf.
31 2
5 6
4" MAX
102 mm MAX

10
Part no. CB-209-1332 05/05/20
Vitality Cabinet
© 2020 Robern, Inc. 701 N. Wilson Ave. Bristol, PA 19007 U.S.A.
800.877.2376 www.robern.com
Installation instructions
RECESS MOUNTING
These instructions are for recess mounting your cabinet. Refer to page 6 for door removal instructions.
1. Make rough opening and frame on all sides. Find the specic model dimensions to make rough opening (page 5).
NOTE: Make sure cabinet door has at least 1” (25mm) clearance above the top of the faucet (including drain stop) and at least 1” below
the ceiling.
2. Electrical eld wiring: Electrical feed through location is indicated below. See page 5 for wire access locations. See page 6 for electric
connection diagram.
1 2
Field Wiring
1" (25.4 mm)
Minimum door to faucet
Rough Opening
Rough Opening
1" (25.4 mm)
Minimum from nished ceiling
A
C
B
ABC
YC24
Cabinet
9-1/2"
(248 mm)
5-3/4"
(146 mm)
14-3/8"
(365 mm)
WARNING: An Electrical option cabinet must be wired to a Class A 20 Amp GFCI (Ground Fault Circuit Interrupter) protected circuit
when used in bathrooms and all other locations required by the National Electric Code.

11
Part no. CB-209-1332 05/05/20
Vitality Cabinet
© 2020 Robern, Inc. 701 N. Wilson Ave. Bristol, PA 19007 U.S.A.
800.877.2376 www.robern.com
Installation instructions
RECESS MOUNTING
3
4
5
3. Place cabinet in rough-in and make sure cabinet is plumb and level.
4. Install a #10 X 2” screw [SS674] through top mounting hole in cabinet side and screw into wall stud as shown. Do not over tighten
screw.
5. Once cabinet is plumb and level, install #10 X 2” screws into wall studs through the three remaining mounting holes. Do not over
tighten screws.
Proceed to page 15 for Final Assembly steps.
[SS674]
#10 x 2" Screw

12
Part no. CB-209-1332 05/05/20
Vitality Cabinet
© 2020 Robern, Inc. 701 N. Wilson Ave. Bristol, PA 19007 U.S.A.
800.877.2376 www.robern.com
Installation instructions
SURFACE MOUNTING
All parts required for surface mounting are included in the optional Surface Mount Kit (see page 4). These instructions are for surface
mounting. Refer to page 6 for door removal instructions.
1. It is strongly recommended that the wall be framed behind the drywall or tile.
2. Electrical eld wiring: Electrical feed through location is indicated below. See page 5 for wire access locations.
NOTE: Make sure cabinet door has at least 1” (25mm) clearance above the top of the faucet (including drain stop) and at least 1” below
the ceiling.
21
Field Wiring
1" (25.4 mm)
Minimum door to faucet
1" (25.4 mm)
Minimum from nished ceiling
B
C
A
ABC
YC24
Cabinet
9-1/2"
(248 mm)
5-3/4"
(146 mm)
14-3/8"
(365 mm)
WARNING: An Electrical option cabinet must be wired to a Class A 20 Amp GFCI (Ground Fault Circuit Interrupter) protected circuit
when used in bathrooms and all other locations required by the National Electric Code.

13
Part no. CB-209-1332 05/05/20
Vitality Cabinet
© 2020 Robern, Inc. 701 N. Wilson Ave. Bristol, PA 19007 U.S.A.
800.877.2376 www.robern.com
Installation instructions
3. Center Z Mounting Bar at cabinet location. Make sure Z Mounting Bar is at least 1” (25mm) above xtures.
4. Locate and drill three 7/32” (5.5mm) holes through the indent line on the mounting bar. Be sure the mounting bar is level. Make sure
Z mounting bar is centered.
5a. Use #10 X 2” screws [SS674] provided to attach the Z Mounting Bar mounting strip to the wall.
5b. If no furring strip or stud is available, use the provided wall anchors [203-1349], making sure that each cabinet is supported by at
least 3 anchors. Drill a 5/16” (8 mm) hole for wall anchors and insert the wall anchor into hole until the anchor ange is ush with the
wall.
5c. Use #10 X 2" screws [SS674] and tighten until there is a strong resistance. DO NOT OVER TIGHTEN.
5b
3
4 5a 5/16"
(8 mm)
203-1349
SS674
1" (25.4 mm)
Minimum
Z Mounting Bar 1" x 3"
7/32"
(5.5 mm)
1" (25.4 mm)
Minimum
Drill Here
SURFACE MOUNTING
[SS674]
#10 x 2" Screw

14
Part no. CB-209-1332 05/05/20
Vitality Cabinet
© 2020 Robern, Inc. 701 N. Wilson Ave. Bristol, PA 19007 U.S.A.
800.877.2376 www.robern.com
Installation instructions
SURFACE MOUNTING
6. Slide three Top Clips [SS712] into the screw channel at the top of the cabinet.
NOTE! Top Clips MUST be inserted into the channel.
7. Lift the cabinet and place the cabinet onto the Z mounting bar.
8. Using the provided #10 X 2" screws [SS674], attach the top of the cabinet to the wall through the top clips as shown.
NOTE! If no stud is available, use wall anchors as described in step 5b.
9. Electrical eld wiring: See page 6 for electric connection diagram. See Page 7 for electrical connection options.
10. Attach Side Kits (included with optional Surface Mount Kit) to cabinet, using provided SS676 screws, from cabinet box interior into
Side Kit mounting brackets.
Proceed to page 15 for Final Assembly steps.
7
9 10
3x
6 8
OR
[SS674]
#10 x 2" Screw
8-[SS672]
8-[SS676]

15
Part no. CB-209-1332 05/05/20
Vitality Cabinet
© 2020 Robern, Inc. 701 N. Wilson Ave. Bristol, PA 19007 U.S.A.
800.877.2376 www.robern.com
Installation instructions
FINAL ASSEMBLY
1B
1A1A
2A
2B
NOTE: The door hinges have a three-way adjustment feature. These adjustments can be made using a #2 Phillips Head screwdriver.
2A. With the hinge slightly closed, you can access the middle screw. This screw will move your door front up and down, adjusting the
height.
2B. With the hinge fully extended, you can access the front and back screws. The front screw will adjust the door front from side to side.
The rear screw will adjust the door in and out.
1A. Mount the doors by pinching the end of the hinge as shown.
1B. If the installation requires, attach the provided hinge clips [SS666] over the elbow of the hinges to stop door swing radius at 110°.

16
Part no. CB-209-1332 05/05/20
Vitality Cabinet
© 2020 Robern, Inc. 701 N. Wilson Ave. Bristol, PA 19007 U.S.A.
800.877.2376 www.robern.com
Installation instructions
FINAL ASSEMBLY
USE AND MAINTENANCE
[SS672]
[SS134]
3 4 5
3. Insert clear snap-in Shelf Clips [SS131] into the holes on the sides of the cabinet.
4. Push one side of the shelf into the left or right clip. Snap the shelf down into the opposite side. If the shelf is too tight, repeat the
process starting from the opposite side.
5. Press the hole plugs [SS134] into the unused holes inside the cabinet. Place the Screw Caps [SS672] over any exposed screw
heads.
NOTE: Do not store items in the cabinet area directly behind the hinge, as damage may occur to cabinet or items.
(12)
[SS131]
[SS131]
CAUTION: Maximum shelf load 34 LBS
The cabinet door and interior are constructed of mirrored glass and aluminum. Use only a damp cloth to clean. Ammonia or vinegar-
based cleaners can damage mirrors.
A 50/50 solution of water and isopropyl alcohol is recommended for cleaning the mirrors. A mild detergent may be used on the surfaces.
When cleaning, spray the cloth, not the cabinet, mirror, or surround surfaces. Do not use abrasive cleansers on any part of the light
xture.
No Ammonia
Sans Ammoniac
Sin Amoniaco
No Vinegar
Sans Vinaigre
Sin Vinagre
No Ammonia
No Vinegar

17
Part no. CB-209-1332 05/05/20
Vitality Cabinet
© 2020 Robern, Inc. 701 N. Wilson Ave. Bristol, PA 19007 U.S.A.
800.877.2376 www.robern.com
Installation instructions
Limited Warranty One Year Term
ROBERN warrants to the original purchaser that, it will, at its election repair, replace, or make appropriate adjustment to products
made by this company shown to have signicant defects in material or workmanship which are reported to ROBERN in writing
within one (1) year from the date of delivery. ROBERN is not responsible for installation costs. The warranty is void in the event the
product is damaged in transit, or if damage or failure is caused by abuse, misuse, abnormal usage, faulty installation, damage in an
accident, improper maintenance, or any repairs other than those authorized by ROBERN. At the expiration of the one year warranty
period, ROBERN shall be under no further obligation under any warranty, expressed or implied, including the implied warranty of
merchantability. ROBERN shall not be liable for any consequential damages arising out of or in connection with the use or performance
of its products. Some states do not allow limitations on how long an implied warranty lasts or do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation or exclusion may not apply to you. Any liability against ROBERN under
any implied warranty, including the warranty of merchantability, is expressly limited to the terms of this warranty. Permission to return
any merchandise under this warranty must be authorized by ROBERN and returned prepaid by the purchaser. Claims under this
warranty should be sent directly to your dealer.
©2020 ROBERN, INC.
ALL RIGHTS RESERVED
WARRANTY

18
No. de pièce / Pieza n.°CB-209-1332 05/05/20
Vitality Cabinet / Vitality Gabinete
© 2020 Robern, Inc. 701 N. Wilson Ave. Bristol, PA 19007 U.S.A.
800.877.2376 www.robern.com
Instructions d'installation / Instrucciones de instalación
Numéros de modèle - 19
Pièce - 20
Dimensions- 21
Retrait de la porte pour faciliter l’installation - 22
Raccordements électriques- 23
Montage Encastré - 27
Montage En Surface - 29
Assemblage Final- 32
Utilisation et Entretien- 33
Garantie- 34
Números de modelo- 19
Partes - 20
Dimensiones - 21
Extracción de la puerta para facilitar la instalación- 22
Conexiones eléctricas- 23
Montaje Empotrado- 27
Montaje En Supericie- 29
Ensamblado Final - 32
Uso y Mantenimiento - 33
Garantía - 34
Ce feuillet d’instructions contient des informations sur la façon
d’installer les armoires de la série Vitality. Cette série est disponible en
différentes tailles. Reportez-vous aux numéros de modèles spéciques
pour les dimensions.
Lisez les instructions spéciques pour faire votre armoire sera monté.
Les armoires peuvent être montés en surface, évidement monté ou.
Conservez ces instructions pour l’utilisation et la référence future. Un
inappropriées annule la garantie de l’installation. Cabinets installés ne
peuvent être retournés.
Si vous rencontrez des problèmes avec votre cabinet, contactez votre
revendeur ou directement Robern.
Garantie limitée - UN AN
Esta hoja de instrucciones contiene información sobre cómo instalar
los gabinetes de la serie Vitality. Esta serie viene en varios tamaños.
Consulte el número de modelo especíco para las dimensiones.
Lea las instrucciones especícas de cómo se va a montar el gabinete.
Los armarios se puede montar la supercie, el recreo montado o
montado.
Guarde estas instrucciones para su uso y referencia futura. Un
incorrectas anula la garantía de instalación. Gabinetes instalados no
se pueden devolver.
Si experimenta algún problema con su gabinete, póngase en contacto
con su distribuidor o Robern directamente.
Garantía limitada - un término del año
VITALITY CABINET / GABINETE
PORTE SIMPLE AVEC SAFE SEAL
Instructions de sécurité importantes - Conservez ces instructions
PUERTA INDIVIDUAL CON SAFE SEAL
Instrucciones importantes de seguridad - Guarde estas instrucciones
TABLE DES MATIÈRES
INFORMATION GÉNÉRALE
CONTENIDO
INFORMACIÓN GENERAL
3000K:
YC2430D4P1L3, YC2440D4P1L3,
YC2430D4P1R3, YC2440D4P1R3

19
No. de pièce / Pieza n.°CB-209-1332 05/05/20
Vitality Cabinet / Vitality Gabinete
© 2020 Robern, Inc. 701 N. Wilson Ave. Bristol, PA 19007 U.S.A.
800.877.2376 www.robern.com
Instructions d'installation / Instrucciones de instalación
NUMÉROS DE MODÈLE NÚMEROS DE MODELO
Utiliser le tableau ci-dessous pour apprendre à construire un
numéro de modèle d'armoire de Vitality. Ce tableau se rapporte
au numéro de modèle pour une armoire Vitality de 24" L x 30"
H x 4" P. Consulter le catalogue des prix Robern pour obtenir
une liste complète des numéros de modèles. Le numéro de
modèle est situé à l’intérieur de votre armoire.
Use la tabla a continuación para aprender cómo construir un
número de modelo de gabinete de vitalidad. Este cuadro hace
referencia al número de modelo para un gabinete de vitalidad
de 24" An. X 30" Alt. X 4" P. Consulte el Libro de precios de
Robern para obtener una lista completa de los números de
modelo. El número de modelo se encuentra dentro de su
gabinete.
Numéros de modèle / Números de modelo
Produit / Producto Y = Vitality
Catégorie / Categoría C = Cabinet / Gabinete
Largeur / Ancho 24 = 23-1/4” (591 mm)
Hauteur / Altura 30 = 30” (762 mm)
40 = 39-3/8" (1000mm)
Profondeur / Profundidad D4 = 4-5/8” (118 mm)
Style de Porte / Estilo de la Puerta P1 = Porte Simple / Puerta Sencilla
Côté Charnière / Lado de la Bisagra L = Gaucher / Zurda
R = Droiter / Diestra
Options / Opciones 3 = 3000K
Y C 24 30 D4 P1 L3

20
No. de pièce / Pieza n.°CB-209-1332 05/05/20
Vitality Cabinet / Vitality Gabinete
© 2020 Robern, Inc. 701 N. Wilson Ave. Bristol, PA 19007 U.S.A.
800.877.2376 www.robern.com
Instructions d'installation / Instrucciones de instalación
(1) Porte simple Vitality Cabinet /
Una sola puerta de Vitality Gabinete
(3) Tablette en verre / Estante de vidrio
(30) MSMK30D4P, (40) MSMK40D4P
Optionnel pour un montage en surface /
Opcional para montaje en supercie
(2) barre de montage en Z /
barra de montaje en “Z”
(2) Panneau latéral de verre /
Panel lateral de vidrio
[SS712]
(3) Support Supérieur /
Montaje Superior
[SS676]
(12) #10 x 1/2 hélice /
#10 x 1/2 tornillo
[SS672]
(12) Bouchon de vis /
Tapa a rosca
[SS674]
(6) 51mm hélice /
51mm tornillo
[203-1349]
(6) ancrages muraux /
ancla de pared
[SS131]
(16) plateau clip /
estante clip
[SS134]
(50 / 100) Bouchon pour trou /
Tapón para los agujeros
[SS672]
(6) Bouchon de vis /
Tapa a rosca
[216-1096]
Sac de matériel / Bolsa de hardware
[SS666]
(4) Pinces pour charnières /
Sujetadores de Bisagra
[SS674]
(6) 51mm hélice /
51mm tornillo
OUTILS NÉCESSAIRES / HERRAMIENTAS NECESARIAS
PIÈCES / PIEZAS