Robus R10MIP-RGB User manual

! Electrical products can cause death or injury, or damage to property. This product must be
installed only by a competent electrician.
1 Ensure mains supply is switched off before commencing work.
2 If necessary cut LED strip to the required length at the locations marked on the strip (Every
5 LED’s),
3 Using the supplied end-cap & glue, glue the end-cap onto the end of the strip. Ensure the
end-cap is secure and sealed.
4 Mounting the strip,
a.Self adhesive strip, remove the protective cover to reveal adhesive strip. Place the strip
onto the desired location and press down firmly. Ensure the strip is secure.
b.Clips: use a minimum of 4 clips per metre. Place the strip along the desired position.
Mark the locations of where the clips are required, keeping them equally spaced. Fix
clips to surface using self adhesive strip or screws. Pull cable tie tightly on to strip, ensure
the strip is secure, cut-off excess cable tie.
5. Mark the appropriate mounting positions on the surface; check that fixings will not impinge
on concealed cables or pipes before drilling.
Attention: The provided accessories “cable pin end” has stated that “Top 1” and “Top 2”,
which should match the same mark on strips. please ensure the correct pin insert the strips.
DMX Control system:
1, Connect the strips to Decoder(RK3EXT) use the live end RKPC2 which is included with the
Strips and connect to decoder. Decoder will operate with RKPS240. IP box (RKIPB2)
available for the decoder if IP rating required.
2, The DMX is supplied with CAT5 signal cable, connect the CAT5 cable between DMX and
decoder (5m max length); DMX is powered by 12V DC supply –RKBSP1; Pin EU plug available:
RKEUPI; the DMX is supplied with a remote control). To connect to additional decoder, 2m of
CAT5 cable supplied (max length between decoder and DMX is10m)
3, Each 20 meter strips can be controlled by 1pcs 240w power supply (RKPS240).
4, The provided accessory Repeater (RKRPT1), will extended to another 20 meter strips
(repeater will operate with RKPS240 ). solve the problem which caused by power limitation and
long transmitting distance.When connecting to end of LED strip please reverse connections,
This will ensure the correct pin connections
RK2RGB Control system:
1, Connect the strips to 200W RGB control (RK2RGB) use the “cable pin end” which included with
the strips, the accessory IP box (RK1PB1) used for connection fitting with
RGB control; the remote control included with RK2RGB.
2, Connect the RGB Control to 240W Power supply (RKPS240), use with accessory IP box
(RKIPB1)
3, Each 20 meter strips can be controlled by 1pcs 240w power supply (RKPS240).
4, Repeater (RKRPT1) is required for more than 20m lengths, used in conjunction with the
RKPS240 another 20m can be controlled.
R10MIP-RGB, R5MIP-RGB
TO fit with DMX Control system or
RK2RGB control system
LED RGB FLEXISTRIP – 24V DC
Please read instructions before commencing installation and retain for
future reference.
Protection against electric shock: Class III (Safety extra low voltage)
Dimensions:
Strip length 10m ; 5m strips
Depth 5.5mm
Width 15mm
Temperature range: -20°C < ta < 40°C
Ingress protection: IP65
Supply: 24V DC
Suitable for mounting on normally flammable surface
Warning! To prevent overheating, the fitting or driver must not be covered by thermal
insulation.
Complies with EN60598 (BS4533)
Specification:
Installation:
Information for the Product user
1. Please note the requirement to dispose of Waste Electrical & Electronic Equipment separately from household waste (WEEE marked with
crossed out wheelie bin symbol).
2. Please consider your role in contributing to re-use and recycling by returning this product at end of life to a collection centre for waste
electrical equipment or a Civic Amenity site, or to a retail outlet from which you are purchasing a replacement.
3. This equipment may contain substances that are hazardous to health and the environment if disposed of carelessly. It is important that it is
separated from normal household waste and recycled in the WEEE chain
4. The “crossed out wheelie bin symbol” on a product indicates this equipment must not be disposed of in normal household waste, but should
be disposed of according to local WEEE regulations
24 VDC
1
Issue 1 280410
The Installation must be carried out by an electrician
LED Group
Western Retail Park Tel: [phone]
Nangor Road Fax: [phone]
Dublin 12 Email: [email protected]
Ireland Website: www.led.ie
Page 1
ISO 9001:2008
Q UAL IT Y ASS U RED C O MPANY

POWER SUPPLY
(RKPS240)
POWER SUPPLY
(RKPS240)
RK2RGB Control system
DMX Control system
Remote
Control
RGB LED RECEIVER
RK2RGB
REPEATER
(RKRPT1)
CUT RGB AT POINT INDICATED
AND JOIN WITH CHOICE OF CONNECTORS
USE HEAT SHRINK AND GLUE FOR IP65
Included with 5m and 10m roll
Also sold separately
JOINER KIT
RKPCI
RKPCL
RKPCT
RKPCX
RKPC2
Includes
End cap and HS
X1
X1
X1
X1
X2
20m max
to go beyond 20m use repeater
plus appropriate power supply
for increments of 20m
(No overall Max length)
CUT AND JOIN
EASY TO
Drivers 1m~5m 5m~20m
RKPS100 yes
RKPS240 yes
set decoder address
1 2 3 4 5 6 7 8 9 10
on
I P B O X O P T I O N A L F O R D E C O D E R A N D R E P E A T E R .
REFERENCE CODE Pr o d u ct Pr o d u ct
RK2RGB Remote + Controller/Receiver
RKPS240
RKPS100
R10M IP-RGB
RKRPT1
RKIPB2
100w power supply
240w power supply
10m Cuttable RGB Joiner Kit
R5M IP-RGB 5m Cuttable RGB Joiner Kit
IP65 box for Decoder or repeater(large)
RKIPB1 IP65 box for Cable connection(small)
Repeater
RK1RGB
RK3EXT
DMX + Remote + BS plug
Decoder
DECODER
(RK3EXT)
To next decoder
max 100pcs.
Remote
Control
BS Plug:RKBSP1
EU Plug:RKEUP1
DMX CONTROL
(RK1RGB)
POWER SUPPLY
(RKPS240)
IP B O X O PT IO N A L F OR D E C OD ER A N D R E PEA T ER .
product code 1m~20m 21m~40m 41m~60m 61~80m
RK2RGB 1 1 1 1
1 2 3 4
0 1 2 3
2X10m 4X10m 6X10m 8X10m
RKPS240
R10MIP-RGB
RKRPT1
RK1RGB 1 1 1 1
IP BOX(small)
(RKIPB1)
2m cat cable
IP BOX (RKIPB2)
Installation diagram:
The Installation must be carried out by an electrician
LED Group
Western Retail Park Tel: [phone]
Nangor Road Fax: [phone]
Dublin 12 Email: [email protected]
Ireland Website: www.led.ie
Page 2
ISO 9001:2008
Q UAL IT Y ASS U RED C O MPANY