Robus R282DEPK-CU User manual

Model No: R282DEPK-CU
Operating mode Maintained or non-maintained
Supply Voltage: 220-240V~50/60Hz
Power Consumption: 28W
Cap type: GR10q
Power Factor: 0.8
Ballast lumen factor: 0.15 Emergency Mode
Battery: 4 x 4Ah Ni-Cd cells
Battery Life: Min 3 years normal use
Discharge Duration: >3 hours after minimum 36Hr charge
Operating temp Range: -5°C < ta < +25°C
IP Rating: 20
Safety Classification: Class I
Length: 240mm
Width: 165mm
Depth: 36mm
Weight: 1.24kg
Warranty: 2 Years
Suitable for mounting on a normally flammable surface
!Not suitable for continuous operation.
Attention: Do no install this pack in an IP66 or higher fitting
indoors. Excessive high temperature may damage electronic
components. Green LED indicator indicates battery charging
mode. Safety and performance in accordance with EN60598-1,
EN60598-2-22, EN50082-1, EN61000-3-2, EN61000-3-3
! Warning. Isolate mains supply before installing or servicing
1. Mark appropriate drilling points on fitting. Where fitting must be
weatherproof apply silicon sealant to fixings.
2. Fit cable gland (if weatherproofing necessary) and introduce
supply cable. (Normally, the emergency fitting must be powered
from the lighting circuit feed)
3. Write installation date on battery
4. Connect wires from unswitched supply, brown to L, Blue to N
and green/yellow to earth marked terminals on gear tray. For
lamp always on, link L to terminal “mains”for lamp switched,
connect switched live wire to terminal “mains”. Note: if mains
terminal not connected, fitting works as non-maintained
emergency luminaire
5. Refit cover.
6. Switch on supply: In the non-maintained unit the green led
should come on indicating correct battery charge has started.
The lamp only lights if the mains supply fails. In the maintained
unit, the green led will come on indicating correct battery
charge has started and the lamp will light (if switched live on).
When supply to the unswitched live is lost, battery will operate
lamp in emergency mode (at reduced light output)
When connected to supply the green led will come on indicating
correct battery charge has started and the lamp will light (if
switched live on). When supply to the unswitched live is lost,
battery will operate lamp in emergency mode (at reduced light
output)
Note Lamp Replacement:
Power to fitting must be disconnected for a minimum of 30
seconds before lamp will come back on. When in operating the
lamp become very hot. Allow to cool before undertaking any
maintenance work.
ROBUS lighting products are suitable for use with standard switch, pull cord, retractive switch and PIRs, however certain guidelines
should be adhered to in order maximise lamp and fitting life.
Estimated average lamp life claims are based on switching cycles of 2 ¾ hours on, ¼ hour off. Switching cycles of shorter duration
may affect lamp and ballast life significantly.
To reduce the detrimental effect of short switching cycles, fittings should be left on or controls set to a minimum of 15 minutes,
preferably 30 minutes, but even these time delay periods may reduce average lamp/ballast life.
Damaged lamps should be replaced promptly. A damaged lamp left unchanged for a long period can lead to control gear damage.
These fittings are not suitable for installation where ambient air temperature is above 25°C
2D Universal Emergency Gear Tray.
C/W LED
R282DEPK-CU Maintained Emergency Gear Tray.
Issue 7 120815
The Installation must be carried out by an electrician
LED Group
Western Retail Park Tel: [phone]
Nangor Road Fax: [phone]
Dublin 12 Email: [email protected]
Ireland Website: www.led.ie
ISO 9001:2008
Q UAL IT Y ASSU RE DCO MPAN Y
SWITCHING AND OPERATION INFORMATION FOR ROBUS LIGHTING PRODUCTS
1
INSTRUCTION MANUAL
PLEASE READ INSTRUCTION BEFORE COMMENCING INSTALLATION AND RETAIN FOR FUTURE REFERENCES.
! Electrical products can cause death or injury, or damage to property. If in any doubt about the installation or
use of this product, consult a competent electrician
Note:
Product technical information and specification may change over time without prior notification
For the latest technical information please visit our web site WWW. ledgrouprobus. com or robusdirect. com
Specifications Installation

Installation and Maintenance Record:
The emergency lighting must be inspected and tested regularly in accordance with local codes of practice: note: for
safety reasons tests should be carried out during daylight hours.
The minimum recommended test schedule is as follows: After installation, allow 36 hours to ensure full battery
charge and then interrupt the supply; check after 3 hours that tube is still lighting.
1. Daily check that charge indicator led is working
2. Monthly, interrupt mains for a short period and check tubes light
3. Six-monthly, check 1 hour duration
4.At the end of year 3 and subsequently every year, check 3 hour duration: batteries must be replaced when they
can no longer support 3 hour operation.
5. Complete record sheet on installation and retain in maintainance file.
6. Update file with ongoing test records for inspection by fire officer or other duly authorised person
Installer
Installation Type
Installation test duration & Date
5st Year
Signed Date
Signed Date
Signed Date
Signed Date
Signed
Month Test
Short
1
2
3
4
5
6
7
8
9
10
11
12
Short
Short
Short
Short
Short
Short
Short
Short
Short
Short
Short
3Hr.
Date
4st Year
3st Year
2st Year
1st Year
LED Group
Western Retail Park Tel: [phone]
Nangor Road Fax: [phone]
Dublin 12 Email: [email protected]
Ireland Website: www.led.ie
ISO 9001:2008
Q UAL IT Y ASSU RE DCO MPAN Y
2
Testing
Information for the Product user
1. Please note the requirement to dispose of Waste Electrical & Electronic Equipment separately from household waste
(WEEE marked with crossed out wheelie bin symbol).
2. Please consider your role in contributing to re-use and recycling by returning this product at end of life to a collection
centrefor waste electrical equipment or a Civic Amenity site, or to a retail outlet from which you are purchasing a replacement.
3. This equipment may contain substances that are hazardous to health and the environment if disposed of carelessly. It
is important that it is separated from normal household waste and recycled in the WEEE chain
4. The “crossed out wheelie bin symbol” on a product indicates this equipment must not be disposed of in normal
household waste, but should be disposed of according to local WEEE regulations

118mm
Ø330mm
1 2
3 4
5 6
SL PL N
SL PL N
The Installation must be carried out by an electrician
LED Group
Western Retail Park Tel: [phone]
Nangor Road Fax: [phone]
Dublin 12 Email: [email protected]
Ireland Website: www.led.ie
ISO 9001:2008
Q UAL IT Y ASSU RE DCO MPAN Y
3
Installation diagram