Robustel GoRugged R3000 Lite User manual

Robustel R3000 Hardware Manual
RT064_HM_R3000 1/11
R3000
Hardware Manual
Version: 1.0.0
Date: Aug. 15, 2022

Robustel R3000 Hardware Manual
RT064_HM_R3000 2/11
Regulatory and Type Approval Information
Table 1: Directives
2011/65/EU
The European RoHS2.0 2011/65/EU Directive was issued by the European parliament
and the European Council on 1 July 2011 on the restriction of the use of certain
Hazardous substances in electrical and electronic equipment.
On June 4, 2015, the Official Journal of the European Union published the RoHS2.0 Amendment
Directive (EU)
In 2015/863, four phthalates (DEHP, BBP, DBP, DIBP) were officially included in the list of restricted
substances in Appendix II of RoHS 2.0 (2011/65/EU).
From July 22, 2019, all electronic and electrical products exported to Europe (except medical and
monitoring equipment) must meet this restriction; from July 22, 2021, medical equipment and
monitoring equipment will also be included in the scope of control.
2012/19/EU
The European WEEE 2012/19/EU Directive was issued by the European parliament
and the European Council on 24 July 2012 on waste electrical and electronic equipment.
2013/56/EU
The European 2013/56/EU Directive is a battery Directive which published in the EU official gazette
on 10 December 2013. The button battery used in this product conforms to the standard of
2013/56/EU directive.
Table 2: Toxic or Hazardous Substances or Elements with Defined Concentration Limits
Name of
the Part
Hazardous Substances
(Pb)
(Hg)
(Cd)
(Cr(VI))
(PBB)
(PBDE)
(DEHP)
(BBP)
(DBP)
(DIBP)
Metal
parts
o
o
o
o
-
-
-
-
-
-
Circuit
modules
o
o
o
o
o
o
o
o
o
o
Cables
and cable
assemblie
s
o
o
o
o
o
o
o
o
o
o
Plastic
and
polymeric
parts
o
o
o
o
o
o
o
o
o
o
o:
Indicates that this toxic or hazardous substance contained in all of the homogeneous materials for this part is
below the limit requirement in RoHS2.0.
X:
Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials for this
part might exceed the limit requirement in RoHS2.0.
-:
Indicates that it does not contain the toxic or hazardous substance.

Robustel R3000 Hardware Manual
RT064_HM_R3000 3/11
Radio Specifications
*May vary on difference models.
Simplified EU Declaration of Conformity
We, Guangzhou Robustel Co., Ltd. are located at 501, Building #2, 63 Yongan Road, Huangpu District, Guangzhou,
China, declare that this radio equipment complies with all applicable EU directives. The full text of the EU DoC is
available at the following internet address:
www.robustel.com/certifications/
FCC Declaration of Conformity
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation.
IC Declaration of Conformity
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic
Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
(1)This device may not cause interference.
(2)This device must accept any interference, including interference that may cause undesired operation of the device.
L’ émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d ’Innovation,
Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes :
(1) L' appareil ne doit pas produire de brouillage;
(2) L' appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d' en
compromettre le fonctionnement.
RF technologies
2G, 3G, 4G, Wi-Fi*, GNSS*
Cellular Frequency*
4G: LTE FDD: B1/B2/B3/B4/B5/B7/B8/B28
LTE TDD: B40
3G: WCDMA: B1/B2/B5/B8
2G: GSM: B2/B3/B5/B8
Oceania
South
America
4G: LTE FDD: B1/B3/B5/B7/B8/B20
LTE TDD: B38/B40/B41
3G: WCDMA: B1/B5/B8
2G: GSM: B3/B8
EMEA
4G: LTE FDD: B1/B2/B3/B4/B5/B7/B8/B12/B13/B18/B19/B20/B25/B26/B28
LTE TDD: B38/B39/B40/B41
3G: WCDMA: B1/B2/B4/B5/B6/B8/B19
2G: GSM: B2/B3/B5/B8
North
America
EMEA
4G: LTE FDD: B1/B3/B8/B18/B19/B26
LTE TDD: B41
3G: WCDMA: B1/B6/B8/B19
Japan
Wi-Fi Frequency
2.4 GHz: 2.412 ~ 2.484 GHz
5 GHz: 4.910 ~ 5.825 GHz
Max RF power
35 dBm@GSM, 25 dBm@WCDMA, 25 dBm@LTE, 18dBm@Wi-Fi

Robustel R3000 Hardware Manual
RT064_HM_R3000 4/11
Radio Frequency Exposure Statement for IC
This device complies with IC exposure limits set forth for an uncontrolled environment. This device shall be installed
and operated with minimum distance 20cm between the radiator & body.
Cet équipement est conforme aux limites d'exposition IC définies pour un environnement non contrôlé. Cet
équipement doit être installé et utilisé avec une distance minimale de 20 cm entre le radiateur et la carrosserie.
Related download link
Find more product documents or tools at:
www.robustel.com/en/documentations/
Technical Support
Tel: [phone]
Email: [e-mail]
Web: www.robustel.com
Document History
Updates between document versions are cumulative. Therefore, the latest document version contains all updates
made to previous versions.
Date
Firmware Version
Document Version
Change Description
Aug. 15, 2022
5.0.0
1.0.0
Initial release.

Robustel R3000 Hardware Manual
RT064_HM_R3000 5/11
Overview
The Robustel Industrial Dual SIM Cellular VPN Router (R3000) is a rugged cellular router offering state-of-the-art
mobile connectivity for machine to machine (M2M) applications.
Package Checklist
Before commencing installation ensure your package has the following components:
Device
3PIN Terminal
Block
7PIN Terminal
Block
RCMS Card
Quick Start Guide
Card
Cellular Antenna
(Optional)
Wi-Fi Antenna
(Optional)
Mounting Kit
(Optional)
Power Supply
(Optional)
Ethernet Cable
(Optional)
Note: The accessories could be different on specific order.
Panel Layout(May Vary on Different Models)
Front View
Top View

Robustel R3000 Hardware Manual
RT064_HM_R3000 6/11
Interface Descriptions
1. PIN Assignment
Note: RS-232/RS-485 depends on the equipment hardware selection, please set according to the actual situation of
the equipment.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
11
12
13
14
15
16
17
PIN
Debug
RS-232
Direction
1
CR
--
R3000 Device
2
CT
--
R3000 Device
3
GND
GND
--
4
--
TXD
R3000 Device
5
--
RXD
R3000 Device
6
--
RTS
R3000 Device
7
--
CTS
R3000 Device
Note: When the device is configured as 2*RS-485, the pin is
defined as follows:
PIN
Debug
RS-485
Direction
4
--
Data+(A)
R3000 Device
5
--
Data- (B)
R3000 Device
PIN
Power
8
Positive
9
Negative
10
GND
PIN
DI/DO
RS-485
Direction
11
Input 1
--
R3000 Device
12
Input 2
--
R3000 Device
13
Output 1
--
R3000 Device
14
Output 2
--
R3000 Device
15
GND
--
--
16
--
Data+(A)
R3000 Device
17
--
Data- (B)
R3000 Device
PIN
DI/DO
RS-232
Direction
11
Input 1
--
R3000 Device
12
Input 2
--
R3000 Device
13
Output 1
--
R3000 Device
14
Output 2
--
R3000 Device
15
IO_GND
--
--
16
--
TXD
R3000 Device
17
--
RXD
R3000 Device
3
--
GND
--
Note: When PIN16/PIN17 is configured as RS-232, the GND of
RS-232 should be connected to PIN3.

Robustel R3000 Hardware Manual
RT064_HM_R3000 7/11
Typical Application:
DI Connection (IN1 for example) DO connect to PNP transistor(OUT1 for example) DO connect to NPN transistor(OUT1 for example)
2. LED Indicators
Name
Color
Status
Description
RUN
Green
On, fast blinking
(250ms blink time)
Router is powered on
(System is initializing)
On, blinking
(500ms blink time)
Router starts operating
Off
Router is powered off
PPP
Green
On, solid
Link connection is working
Off
Link connection is not working
USR-OpenVPN
Green
On, solid
OpenVPN connection is established
Off
OpenVPN connection is not established
USR-IPsec
Green
On, solid
IPsec connection is established
Off
IPsec connection is not established
USR-Wi-Fi
Green
On, solid
Wi-Fi is enabled and working properly
Off
Wi-Fi is disabled or not working properly
Green
On, solid
High Signal strength (21-31) is available
Yellow
On, solid
Medium Signal strength (11-20) is available
Red
On, solid
Low Signal strength (1-10) is available
--
Off
No signal
NET
Green
On, solid
Connection to 4G network is established
Yellow
On, solid
Connection to 3G network is established
Red
On, solid
Connection to 2G network is established
--
Off
Connection to network is not established or establishing
SIM
Green
On, solid
Main card is being used
On, blinking
Backup card is being used
Off
NO SIM card
Note: You can choose the display type of USR LED. For more details, please refer to
RT123_SM_RobustOS Software Manual Service > Advanced > System >System Settings > User LED Type.

Robustel R3000 Hardware Manual
RT064_HM_R3000 8/11
3. Reset Button
Function
Operation
Reboot
Press and hold the RST button for 2~ 5 seconds under the operating status.
Restore to default
configuration
Press and hold the RST button for 5~10 seconds, the RUN LED starts blinking quickly, the router will restore to default
configuration.
Restore to factory
default settings
Once the operation of restoring default configuration is performed twice within one minute, the router will restore to factory
default settings.
Note: The more details please refer to RT123_SM_RobustOS Software Manual, 2.3 Factory Reset.
4. Ethernet Ports. There are 2 Ethernet ports on R3000 Router, including ETH0 and ETH1. Each Ethernet port has
2 LED indicators. The yellow one is a link indicator, while the green one is a speed indicator. For details about
status, see the table below.
Indicator
Status
Description
Link indicator
On, solid
Connection is established
On, blinking
Data is being transferred
Off
Connection is not established
Speed indicator
On, solid
100 Mbps mode
Off
10 Mbps mode
5. USB Interface
Function
Operation
Firmware upgrade
USB interface is used for batch firmware upgrading, but cannot be used for sending or receiving data from slave devices which
connected to it. You can insert a USB storage device into the router’s USB interface, such as a U disk or a hard disk. If there have a
supported configuration file or a router firmware in this USB storage device, the router will automatically update the
configuration file or the firmware. For more details, see RT123_SM_RobustOS Software Manual.

Robustel R3000 Hardware Manual
RT064_HM_R3000 9/11
Hardware Installation
1. SIM Card Installation. Loosen the screws associated with the cover by using a screwdriver and then find the
SIM card slot/Micro SD card slot. Press the card with finger until you hear a click and then tighten the screws
associated with the cover by using a screwdriver. Put back the cover and tighten the screws associated with
the cover by using a screwdriver.
2. Antenna Installation. Rotate the antenna into the antenna connector accordingly.
3. Terminal Block Installation. Insert the terminal blocks into the interfaces connector, then can connect the
devices or sensors to the gateway via corresponding interfaces e.g. RS232/RS485, DIDO...
4. Mounting Kit installation. (Optional)
Wall mounting DIN rail mounting

Robustel R3000 Hardware Manual
RT064_HM_R3000 10/11
5. Grounding the Device. Grounding will help to prevent the noise effect due to electromagnetic interference
(EMI). Connect the device to the site ground wire by the grounding screw before powering on.
6. Power Supply installation. Following to the color of the head, connect the cable marked red to the positive
pole through a terminal block, and connect the yellow one to the negative in the same way. The last step is to
plug the power adapter into your socket.
Note: The range of power voltage is 9 to 60V DC.

Robustel R3000 Hardware Manual
RT064_HM_R3000 11/11
Support: [e-mail]
Website: www.robustel.com
©2022 Guangzhou Robustel Co., Ltd.
All rights reserved. Subject to change without notice.
Login to the Device
1. Connect the router’s Ethernet port to a PC with a
standard Ethernet cable.
2. Before logging in, manually configure the PC with
a static IP address on the same subnet as the
gateway address, click and configure "Use the
following IP address".
3. To enter the gateway's web interface, type
http://192.168.0.1 into the URL field of your
Internet browser.
4. Use login information shown in the product label
when prompted for authentication.
5. After logging in, the home page of the web
interface is displayed, then you can view system
information and perform configuration on the
device.
6. The automatic APN selection is ON by default, if
need to specify your own APN, please go to the
menu Interface->Link Manager->Link
Setting->WWAN Settings to finish the specific
setting.
7. The more configuration details please refer to
RT123_SM_RobustOS Software Manual.
(END)