Robustel GoRugged R2000 User manual

Hardware Installation Quick Guide
R2000 Dual--
Industrial Dual Module Cellular VPN Router with
Power over Ethernet
Package Contents
Before installing the R2000 Dual Router, verify the kit contents as following:

1 x Robustel R2000 Dual Industrial Dual Module Cellular VPN Router with Power over Ethernet
1 x Terminal block for power
1 x Quick Start Guide with download link of other documents or tools
Optional Accessories (sold separately)
AC/DC power adapter
POE power adapter
SMA cellular antenna for 3G/4G LTE
Stubby/magnet RP-SMA Wi-Fi antenna
Wall mounting kit
35 mm DIN rail mounting kit
*If any of the above items is missing or damaged, please contact your Robustel sales
representative*
Environmental Requirements
Power input: 9 to 48V DC
Power consumption: 100 mA@12 V in idle state;
800 mA (peak)@12 V in communication state
Operating temperature: -40 to 70°C
Relative humidity: 5 to 95% RH
Reset Button
Reboot: Press and hold the Reset button for at least 2~7 seconds under the operating status.
Restore to factory default settings: Wait for 5 seconds after powering up the router, press and hold
the Reset button by a small non-conductive stick with a blunt end until all twelve LEDs blinking one by
one, and release the button within 5 second to return the router to factory defaults.
Ethernet Ports
R2000 Dual Router has five Ethernet ports. Eth0 is a WAN port and Eth1~Eth4 are LAN ports
supporting POE feature.
Every Ethernet port has two LED indicators, while each indicator has three states. The yellow one is
Link Indicator and the green one doesn’t mean anything. For details see the table below:
Indicator
State
Description
Link Indicator
On
Connection is working
On, blinking
Data is being transmitted
Off
Connection is not working

Device should be in accordance with the
reliable grounding to avoid lighting
strike.
Use the rated power adapter for the
device, and note the power polarity
when wiring.
Pay attention to waterproof in storage,
transporting and operating environment.
Place the device on the horizontal
surface.
Damaging the product’s warranty
labeling cannot enjoy the free
maintenance in warranty period.
CAUTION！
Hardware Introduction
Overview

Hardware Installation
Step 1: After opening the package, refer to the following figure to insert the SIM into the router.
Note: Recommended torque for inserting is 0.5 N.m, and the maximum allowed is 0.7N.m.
Step 2: Attach the SMA external antenna to the router’s antenna interface and twist tightly.
Make sure the antenna is within the correct frequency range
Note: Recommended torque for mounting is 0.35 N.m.
Step 3: Connect the router to the site ground wire by the ground screw before powering on (Optional) .
Step 4: Connect the router’s Ethernet port (Eth0/Eth1/Eth2/Eth3) to a PC via a standard cross-over cable.
Step 5: The router supports flat surface placement, wall mounting and DIN rail mounting.
Wall mounting:
Use 4 pcs of M2.5*4 flat head Phillips screws to fix the wall mounting kits to the router, and then
use 2 pcs of M3 drywall screws to mount the router associated with the wall mounting kit on the
wall.
Note: Recommended torque for mounting is 0.5 N.m and the maximum allowed is 0.7 N.m.
Din rail mounting:
Use 3 pcs of M3*6 flat head Phillips screws to fix the DIN rail to the router, and then hang the DIN
rail on the bracket. It is necessary to choose the standard bracket.
Note: Recommended torque for mounting is 1.0 N.m, and the maximum allowed is 1.2 N.m.
Step 6: R2000 Dual Router supports reverse polarity protection, but always refers to the figure below to
connect the power adapter correctly. There are two cables associated with the power adapter.
Following to the color of the head, connect the cable marked red to the positive pole through a
terminal block, and connect the yellow one to the negative in the same way.
LEDs
Name
Color
State
Description
RUN
Green
On, 1/2 sec blink
Router is ready
On, 1 sec blink
Router is booting
Off
Router is powered off
PPP
Green
LED 1 is on
SIM1 PPP connection is working
LED 2 is on
SIM2 PPP connection is working
USR
Green
On
OpenVPN: OpenVPN is connected
IPsec: IPsec is connected
Wi-Fi: Wi-Fi is connected
Off
OpenVPN: OpenVPN is disconnected
IPsec: IPsec is disconnected
Wi-Fi: Wi-Fi is disconnected
NET
(LED 1 stands for
SIM 1, LED 2
stands for SIM 2)
Green
On, blinking green
Unable to connect to the best network.
E.g. When R2000 Dual uses the 4G SIM card but
cannot connect to the 4G network, the NET LED
will always blink. The condition of 3G and 2G
network will, too.
On, solid green
Connect to the best network.
E.g. When R2000 Dual uses the 4G SIM card
and connects to the 4G network, the NET LED
will turn to solid green. The condition of 3G and
2G network will, too.
Off
Unable to access any network.
Signal Strength
(Light 1 stands
for SIM 1, light 2
stands for SIM 2)
Green
All LEDs are on
Signal level: 21-31 (Optimum signal level)
Green
Two LEDs are on
Signal level: 11-20 (Average signal level)
Green
Only one LED is on
Signal level: 1-10 (Abnormal signal level)
When the network disconnected, those three signal LEDs are designed as a
binary combination code to indicate a series of error report
On: 1 Off: 0
001 AT command failed
010 no SIM card detected
011 it need to enter the PIN code
100 it need to enter the PUK code
101 registration failed
110 something wrong happened in the module
Insert SIM card
Wall mounting
DIN rail mounting

E-mail: [email protected]
© 2016 Guangzhou Robustel Technologies Co., Limited. All rights reserved. Subject to change without notice. Web: www.robustel.com
Note: The range of power voltage is 9 to 48V DC.
Step 7: R2000 Dual Router also supports POE feature. Please refer to the figure below to
connect the power adapter correctly.
Note: The range of power voltage is 48 to 57V DC.
POE Connection
(OPTIONAL)
R2000 Dual’s four fast Ethernet LAN ports support POE feature (Voltage range: 48 to 57V DC), which
can electrify the network terminal devices such as IP camera and other WLAN AP etc. See figure below
for more details.