Rockville RWM72U User manual

RWM72U
DUAL UHF WIRELESS HANDHELD MICROPHONE SYSTEM w/DIGITAL DISPLAY
OWNER’S MANUAL

Thank you for purchasing this Rockville RWM72U Dual Wireless UHF Microphone System.
Please read this owner’s manual carefully for proper use of your Rockville Wireless
UHF Microphone System. Should you need technical assistance, please call our
technical help line at 1-646-758-0144, Monday through Friday, 9am to 5pm EST.
Includes:
• Receiver with LED display
• 2 hand-held mics with LED display
• ¼˝ to ¼˝ Audio output cable
• Power adapter
• 2 antennas
• 4 AA batteries
• Owner’s manual
• Warranty card

Receiver (Front)
Receiver (Back)
bcdeg f
a a
a. Antenna
b. Power on/off
c. Volume controls
d. CH A LED indicator
e. Audio signal LED indicator
f. LCD Display: shows frequency and channel
g. CH B LED indicator
a. Antenna B
b. Mic B XLR out
c. ¼˝ TRS Mix out
d. Power input (110/220 volt power supply for worldwide use)
e. Mic A XLR out
f. Antenna A
abcdef

Microphone
c
e
b
a
a. Microphone windscreen
b. LCD Display: shows frequency
c. Power on/off
d. Battery compartment.
Please note: LCD screen will gradually darken, indicating that the battery is low
and needs to be replaced.

Setup and Operation
• The receiver should be placed in an area that is stable and least likely to
shake the unit.
• The receiver should be at least 3 ft off the ground for optimal transmission.
• Connect the antenna and power supply provided.
• The antenna should extend vertically.
• Switch on the receiver.
• Switch on the microphones.
• Adjust volume as necessary.
Tip:
To minimize feed-
back avoid operating
the microphones in
close proximity of or
in front of speakers.
The RWM72U features a ¼˝ mix output if you want to connect to a single mixer
channel so as to control the mic mix. There are also individual volume controls
and XLR outputs so you can plug Mic A into one mixer channel and Mic B into
another mixer channel in case you want to have 2 different sound mixes on each
mic.
Please note: Although you can use either mic or line level inputs, line level inputs
are preferred when available. Be sure to adjust the volume on the mic receiver
according to the input you choose.

Features and Specs
• High performance and long range
• Includes microphone receiver and (2) handheld microphones
• High sensitivity cartridge
• Unidirectional
• Wireless cardioid polar pattern
• Dual lter design to limit feedback and interference
• Durable composite microphone construction with our signature comfortable
rubbery coating
• Color coded microphones
• LCD display
• Low power consumption for longer battery life
• Latest UHF digital technology is controlled by a central microchip to ensure
stable voice quality
• (2) Individual XLR outputs if you want to control each mic mix separately
• Mixed ¼˝ TRS output to control both mics through one channel on your mixer
• Individual microphone volume controls
• 110/220 volt switchable for worldwide use
Operating Range*: 250´ – 350´ (indoor), 200´ – 300´ (outdoor)
Frequency Range: 500MHz – 599MHz
Frequency Stability: ±0.005%
Modulation Mode: UHF
Frequency Response: 50Hz – 16KHz(±3dB)
Dynamic Range: 110dB
S/N: 90dB
T.H.D: <0.1%(1KHz)
Audio Output Impedance: 600Ω
System Distortion: ≤0.5%
Sensitivity: <2μV
Audio Output Jack: (2) XLR balanced, (1) ¼˝ mix out
Power Voltage: AC110V – 240V 50/60Hz
Operating Temperature: 14°F – 122°F
Mic Battery Operating Time: up to 10 hours
Power Supply: 1.5V x 2
*Operating range is subject to environmental conditions. Results may vary.

Troubleshooting
Problem Solution
No sound or faint
sound
•Verify all sound system connections or adjust
channel volume as needed.
•Verify that the receiver is connected to the mix-
er/amplier.
•Turn on microphone. A dark LDC screen indi-
cates that the battery is low. Please replace or
recharge the battery.
•Make sure the batteries are installed correctly.
•Make sure AC adapter is securely plugged into
electrical outlet.
•Make sure receiver is powered on.
Audio artifacts or
dropouts
•Identify nearby sources of interference (cell
phones, Wi-Fi access points, signal processor,
etc...) and shutdown or remove source.
•Charge or change microphone battery.
•System must be set up within recommended
range and receiver kept away from metallic
surfaces.
•Microphone must be used in line of sight from
receiver for optimal sound.
Distortion Reduce microphone channel volume.
Sound level
variations when
switching to dif-
ferent sources
Adjust microphone volume as necessary.
Transmitter
information does
not appear on the
Receiver LCD
Microphone is off.

Visit us at:
RockvilleAudio.com
©2019 ROCKVILLE // The information presented is subject to change
and or improvement without notice.